Separators, solid electrolytes

A completely separate family of conducting polymers is based on ionic conduction polymers of this kind (Section 11.3.1.2) are used to make solid electrolyte membranes for advanced batteries and some kinds of fuel cell. 

Conventional batteries consist of a liquid electrolyte separating two solid electrodes. In the Na/S battery this is inverted a solid electrolyte separates two liquid electrodes a ceramic tube made from the solid electrolyte sodium /5-alumina (p. 249) separates an inner pool of molten. sodium (mp 98°) from an outer bath of molten sulfur (mp 119°) and allows Na" " ions to pass through. The whole system is sealed and is encased in a stainless steel canister which also serves as the sulfur-electrode current collector. Within the battery, the current is passed by Na+ ions which pass through the solid electrolyte and react with the sulfur. The cell reaction can be written formally as... 

The tape-casting method makes possible the fabrication of films in the region of several hundred micrometers thick. The mechanical strength allows the use of such a solid electrolyte as the structural element for devices such as the high-temperature solid oxide fuel cell in which zirconia-based solid electrolytes are employed both as electrolyte and as mechanical separator of the electrodes. 

In the Na/S system the sulfur can react with sodium yielding various reaction products, i.e. sodium polysulfides with a composition ranging from Na2S to Na2S5. Because of the violent chemical reaction between sodium and sulfur, the two reactants have to be separated by a solid electrolyte which must be a sodium-ion conductor. / " -Alumina is used at present as the electrolyte material because of its high sodium-ion conductivity. 

Jahn-Teller distortions 309 ff Japanese separators 264, 267 Joule effect, heat losses 13 jump frequency, solid electrolytes 532 Jungner nickel cadmium batteries 22... 

PP/PE/PP trilayer separators 556 practical batteries 19-61 precipitation, solid electrolytes 540 precursors... 

Fuel cells such as the one shown on Fig. 3.4a convert H2 to H20 and produce electrical power with no intermediate combustion cycle. Thus their thermodynamic efficiency compares favorably with thermal power generation which is limited by Carnot-type constraints. One important advantage of solid electrolyte fuel cells is that, due to their high operating temperature (typically 700° to 1100°C), they offer the possibility of "internal reforming" which permits the use of fuels such as methane without a separate external reformer.33 36... 

We start by considering a schematic representation of a porous metal film deposited on a solid electrolyte, e.g., on Y203-stabilized-Zr02 (Fig. 5.17). The catalyst surface is divided in two distinct parts One part, with a surface area AE is in contact with the electrolyte. The other with a surface area Aq is not in contact with the electrolyte. It constitutes the gas-exposed, i.e., catalytically active film surface area. Catalytic reactions take place on this surface only. In the subsequent discussion we will use the subscripts E (for electrolyte) and G (for gas), respectively, to denote these two distinct parts of the catalyst film surface. Regions E and G are separated by the three-phase-boundaries (tpb) where electrocatalytic reactions take place. Since, as previously discussed, electrocatalytic reactions can also take place to, usually,a minor extent on region E, one may consider the tpb to be part of region E as well. It will become apparent below that the essence of NEMCA is the following One uses electrochemistry (i.e. a slow electrocatalytic reaction) to alter the electronic properties of the metal-solid electrolyte interface E. 

The speed of p- and n-type doping and that of p-n junction formation depend on the ionic conductivity of the solid electrolyte. Because of the generally nonpolar characteristics of luminescent polymers like PPV, and the polar characteristics of solid electrolytes, the two components within the electroactive layer will phase separate. Thus, the speed of the electrochemical doping and the local densities of electrochemically generated p- and n-type carriers will depend on the diffusion of the counterions from the electrolyte into the luminescent semiconducting polymer. As a result, the response time and the characteristic performance of the LEC device will highly depend on the ionic conductivity of the solid electrolyte and the morphology and microstructure of the composite. 

A solid electrolyte is an ionic conductor and an electronic insulator. Ideally, it conducts only one ionic species. Aside from a few specialty applications in the electronics industry, solid electrolytes are used almost exclusively in electrochemical cells. They are particularly useful where the reactants of the electrochemical cell are either gaseous or liquid however, they may be used as separators where one or both of the reactants are solids. Used as a separator, a solid electrolyte permits selection of two liquid or elastomer electrolytes each of which is matched to only the solid reactant with which it makes contact. 

Electrochemical cells are of two types power cells and sensors. In an ideal power cell, the ionic current through the electrolyte inside the cell matches an electronic current through an external load. The solid electrolyte is in the form of a membrane of thickness L and area A that separates electronically the two electrodes of the cell. Any internal electronic current across the electrolyte reduces the power output. The internal resistance to the ionic current is... 

At this time the only commercially available all-solid-state cell is the lithium battery containing Lil as the electrolyte. Many types of solid lithium ion conductors including inorganic crystalline and glassy materials as well as polymer electrolytes have been proposed as separators in lithium batteries. These are described in the previous chapters. A suitable solid electrolyte for lithium batteries should have the properties... 

Polymer electrolytes (e.g., poly (ethylene oxide), poly(propylene oxide)) have attracted considerable attention for batteries in recent years. These polymers form complexes with a variety of alkali metal salts to produce ionic conductors that serve as solid electrolytes. Their use in batteries is still limited due to poor electrode/electrolyte interface and poor room temperature ionic conductivity. Because of the rigid structure, they can also serve as the separator. Polymer electrolytes are discussed briefly in section 6.2. 

Lithium secondary batteries can be classified into three types, a liquid type battery using liquid electrolytes, a gel type battery using gel electrolytes mixed with polymer and liquid, and a solid type battery using polymer electrolytes. The types of separators used in different types of secondary lithium batteries are shown in Table 1. The liquid lithium-ion cell uses microporous polyolefin separators while the gel polymer lithium-ion cells either use a PVdF separator (e.g. PLION cells) or PVdF coated microporous polyolefin separators. The PLION cells use PVdF loaded with silica and plasticizer as separator. The microporous structure is formed by removing the plasticizer and then filling with liquid electrolyte. They are also characterized as plasticized electrolyte. In solid polymer lithium-ion cells, the solid electrolyte acts as both electrolyte and separator. 

---