Separator residence time

In FCC there are therefore four separate residence times, and the riser and regenerator are each described by two coupled mass-balance equations. The mass flow rates of catalyst between the reactors are the same since catalyst is recycled. 

The separation residence time determines the relationship between separator size and separator throughput. Extensive property determinations were made during prior development and testing of candidate CSSX solvent formulations [49],... 

To satisfy physical limitations, modifications to the diameters are made depending upon the magnitude of the compressible flow effects in each of the reactor sections. Lengths are geometrically scaled in the reactor throat. However, the diffuser angle is forced below a maximum angle of 6° to avoid flow separation. Residence times are controlled by appropriate variation of the length of the reactor s cylindrical section. 

Entrained liquid in overhead gas sensor error/[entrainment GL]. Incomplete separation of oil from water faulty design of separator/residence time of liquid phases too short/liquid velocity in the decant phases too fast/Marangoni instabil-ities/liquid feed velocity too fast/poor distribution of liquid feeds/faulty location of exit nozzles for liquid phases/overflow baffle corroded and failure/interface level at the wrong location/faulty control of interface/no vortex breaker at water and heavy oil exit nozzles/liquid exit velocities too high/ emulsification]. ... 

One cannot easily quantify the critical fluid level since it is highly dependent on liquid properties, but a simple guideline can be used. If the gas separator residence time is longer than the minimum separation time (time required for the average... 

In the higher pressure sub-region, which may be extended to relative pressure up to 01 to 0-2, the enhancement of the interaction energy and of the enthalpy of adsorption is relatively small, and the increased adsorption is now the result of a cooperative effect. The nature of this secondary process may be appreciated from the simplified model of a slit in Fig. 4.33. Once a monolayer has been formed on the walls, then if molecules (1) and (2) happen to condense opposite one another, the probability that (3) will condense is increased. The increased residence time of (1), (2) and (3) will promote the condensation of (4) and of still further molecules. Because of the cooperative nature of the mechanism, the separate stages occur in such rapid succession that in effect they constitute a single process. The model is necessarily very crude and the details for any particular pore will depend on the pore geometry. 

Cyclohexane, produced from the partial hydrogenation of benzene [71-43-2] also can be used as the feedstock for A manufacture. Such a process involves selective hydrogenation of benzene to cyclohexene, separation of the cyclohexene from unreacted benzene and cyclohexane (produced from over-hydrogenation of the benzene), and hydration of the cyclohexane to A. Asahi has obtained numerous patents on such a process and is in the process of commercialization (85,86). Indicated reaction conditions for the partial hydrogenation are 100—200°C and 1—10 kPa (0.1—1.5 psi) with a Ru or zinc-promoted Ru catalyst (87—90). The hydration reaction uses zeotites as catalyst in a two-phase system. Cyclohexene diffuses into an aqueous phase containing the zeotites and there is hydrated to A. The A then is extracted back into the organic phase. Reaction temperature is 90—150°C and reactor residence time is 30 min (91—94). 

Fresh butane mixed with recycled gas encounters freshly oxidized catalyst at the bottom of the transport-bed reactor and is oxidized to maleic anhydride and CO during its passage up the reactor. Catalyst densities (80 160 kg/m ) in the transport-bed reactor are substantially lower than the catalyst density in a typical fluidized-bed reactor (480 640 kg/m ) (109). The gas flow pattern in the riser is nearly plug flow which avoids the negative effect of backmixing on reaction selectivity. Reduced catalyst is separated from the reaction products by cyclones and is further stripped of products and reactants in a separate stripping vessel. The reduced catalyst is reoxidized in a separate fluidized-bed oxidizer where the exothermic heat of reaction is removed by steam cods. The rate of reoxidation of the VPO catalyst is slower than the rate of oxidation of butane, and consequently residence times are longer in the oxidizer than in the transport-bed reactor. 

The hydrocyclone, commonly referred to simply as cyclone, is a nonmechanical sedimentation-type classifier (2,6,10,27) (Fig. 7). It has no moving parts or power attachments directly connected to it. The hydrocyclone has become the workhorse of most mineral processing operations because of its simplicity, short residence time, compactness, and low cost of operation. It is, however, characterized by lack of sharpness of separation. Equipment... 

Some slurry processes use continuous stirred tank reactors and relatively heavy solvents (57) these ate employed by such companies as Hoechst, Montedison, Mitsubishi, Dow, and Nissan. In the Hoechst process (Eig. 4), hexane is used as the diluent. Reactors usually operate at 80—90°C and a total pressure of 1—3 MPa (10—30 psi). The solvent, ethylene, catalyst components, and hydrogen are all continuously fed into the reactor. The residence time of catalyst particles in the reactor is two to three hours. The polymer slurry may be transferred into a smaller reactor for post-polymerization. In most cases, molecular weight of polymer is controlled by the addition of hydrogen to both reactors. After the slurry exits the second reactor, the total charge is separated by a centrifuge into a Hquid stream and soHd polymer. The solvent is then steam-stripped from wet polymer, purified, and returned to the main reactor the wet polymer is dried and pelletized. Variations of this process are widely used throughout the world. 

Flotation. Flotation (qv) is used alone or in combination with washing and cleaning to deink office paper and mixtures of old newsprint and old magazines (26). An effective flotation process must fulfill four functions. (/) The process must efficiently entrain air. Air bubble diameter is about 1000 p.m. Typically air bubbles occupy 25—60% of the flotation cell volume. Increa sing the airRquid ratio in the flotation cell is said to improve ink removal efficiency (27). (2) Ink must attach to air bubbles. This is primarily a function of surfactant chemistry. Air bubbles must have sufficient residence time in the cell for ink attachment to occur. (3) There must be minimal trapping of cellulose fibers in the froth layer. This depends on both cell design and surfactant chemistry. (4) The froth layer must be separated from the pulp slurry before too many air bubbles coUapse and return ink particles to the pulp slurry. 

Black Liquor Soap Recovery. Black Hquor soap consists of the sodium salts of the resin and fatty acids with small amounts of unsaponifiables. The soap is most easily separated from the black Hquor by skimming at an intermediate stage, when the black Hquor is evaporated to 25% soHds (7). At this soHds level, the soap rises in the skimmer at a rate of 0.76 m/h. At higher soHds concentrations, the tall oil soap is less soluble, but higher viscosity lowers the soap rise rate and increases the necessary residence times in the soap skimmer beyond 3—4 hours. The time required for soap recovery can be reduced by installing baffles, by the use of chemical flocculants (8,9), and by air injection into the suction side of the soap skimmer feed pump. Soap density is controUed by the rate of air injection. Optimum results (70% skimmer efficiency) are obtained at a soap density of 0.84 kg/L (7 lb/gal). This soap has a minimum residual black Hquor content of 15% (10—12). 

A typical reactor operates at 600—900°C with no catalyst and a residence time of 10—12 s. It produces a 92—93% yield of carbon tetrachloride and tetrachloroethylene, based on the chlorine input. The principal steps in the process include (/) chlorination of the hydrocarbon (2) quenching of reactor effluents 3) separation of hydrogen chloride and chlorine (4) recycling of chlorine to the reactor and (i) distillation to separate reaction products from the hydrogen chloride by-product. Advantages of this process include the use of cheap raw materials, flexibiUty of the ratios of carbon tetrachloride and tetrachloroethylene produced, and utilization of waste chlorinated residues that are used as a feedstock to the reactor. The hydrogen chloride by-product can be recycled to an oxychlorination unit (30) or sold as anhydrous or aqueous hydrogen chloride. 

Still another process, called BI-GAS, was developed by Bituminous Coal Research in a 73 t/d pilot plant in Homer City, Peimsylvania. In this entrained-bed process, pulverized coal slurry was dried and blown into the second stage of the gasifier to contact 1205°C gases at ca 6.9 MPa (1000 psi) for a few seconds residence time. Unreacted char is separated and recycled to the first stage to react with oxygen and steam at ca 1650°C to produce hot gas and molten slag that is tapped. 

As an idealization of the classified-fines removal operation, assume that two streams are withdrawn from the crystallizer, one corresponding to the product stream and the other a fines removal stream. Such an arrangement is shown schematically in Figure 14. The flow rate of the clear solution in the product stream is designated and the flow rate of the clear solution in the fines removal stream is set as (R — 1) - Furthermore, assume that the device used to separate fines from larger crystals functions so that only crystals below an arbitrary size are in the fines removal stream and that all crystals below size have an equal probabiHty of being removed in the fines removal stream. Under these conditions, the crystal size distribution is characterized by two mean residence times, one for the fines and the other for crystals larger than These quantities are related by the equations... 

Salting-out crystalli tion operates through the addition of a nonsolvent to the magma ia a crystallizer. The selection of the nonsolvent is based on the effect of the solvent on solubiHty, cost, properties that affect handling, iateraction with product requirements, and ease of recovery. The effect of a dding a nonsolvent can be quite complex as it iacreases the volume required for a given residence time and may produce a highly nonideal mixture of solvent, nonsolvent, and solute from which the solvent is difficult to separate. 

A simple separator used to recover the magnetic particles consists of a series of disks mounted on a shaft. Each disk has a number of permanent magnets mounted flush with the surface at its perimeter. The disks rotate into and out of the Hquid containing the suspended magnetic material and lift the magnetic particles out of the stream. The magnets are then scraped clean (Eig. 10). Very low residence times are needed for removal of the particles compared to settling or flotation (142). 

Operating holdup contributes effectively to mass-transfer rate, since it provides residence time for phase contact and surface regeneration via agglomeration and dispersion. Static holdup is hmited in its contribution to mass-transfer rates, as indicated by Thoenes and Kramers [Chem. Eng. ScL, 8, 271 (1958)]. In laminar regions holdup in general has a negative effecl on the efficiency of separation. 

In design of separating chambers, static vessels or continuous-flow tanks may be used. Care must be taken to protect the flow from turbulence, which coiild cause back mixing of partially separated fluids or which could cany unseparated hquids rapidly to the separated-hquid outlet. Vertical baffles to protect rising biibbles from flow currents are sometimes employed. Unseparated fluids should be distributed to the separating region as uniformly and with as little velocity as possible. When the bubble rise velocity is quite low, shallow tanks or flow channels should be used to minimize the residence time required. 

---