Saturated sodium chloride

In a 500 ml. three-necked flask, equipped with a thermometer, a sealed Hershberg stirrer and a reflux condenser, place 32-5 g. of phosphoric oxide and add 115-5 g. (67-5 ml.) of 85 per cent, orthophosphoric acid (1). When the stirred mixture has cooled to room temperature, introduce 166 g. of potassium iodide and 22-5 g. of redistilled 1 4-butanediol (b.p. 228-230° or 133-135°/18 mm.). Heat the mixture with stirring at 100-120° for 4 hours. Cool the stirred mixture to room temperature and add 75 ml. of water and 125 ml. of ether. Separate the ethereal layer, decolourise it by shaking with 25 ml. of 10 per cent, sodium thiosulphate solution, wash with 100 ml. of cold, saturated sodium chloride solution, and dry with anhydrous magnesium sulphate. Remove the ether by flash distillation (Section 11,13 compare Fig. II, 13, 4) on a steam bath and distil the residue from a Claisen flask with fractionating side arm under diminished pressure. Collect the 1 4-diiodobutane at 110°/6 mm. the yield is 65 g. 

Into a 250 or 500 ml. round-bottomed flask provided with a reflux condenser place 46 g. (38 ml.) of A.R. formic acid (98/100 per cent.) and 37 g. (46 ml.) of n-butyl alcohol. Reflux for 24 hours. Wash the cold mixture with small volumes of saturated sodium chloride solution, then with saturated sodium bicarbonate solution in the presence of a httle... 

This product is sufficiently pure for the preparation of phenylacetic acid and its ethyl ester, but it contains some benzyl tso-cyanide and usually develops an appreciable colour on standing. The following procedure removes the iso-cyanide and gives a stable water-white compound. Shake the once-distilled benzyl cyanide vigorously for 5 minutes with an equal volume of warm (60°) 60 per cent, sulphuric acid (prepared by adding 55 ml. of concentrated sulphuric acid to 100 ml. of water). Separate the benzyl cyanide, wash it with an equal volume of sa+urated sodium bicarbonate solution and then with an equal volume of half-saturated sodium chloride solution- Dry with anhydrous magnesium sulphate and distil under reduced pressure. The loss in washing is very small (compare n-Butyl Cyanide, Section 111,113, in which concentrated hydrochloric acid is employed). 

A sodium stannite solution was prepared by addition of aqueous sodium hydroxide (2.5 mol, lOOg) to aqueous stannous chloride (0.25 mol, 56g). The initially formed precipitate redissolved to form a clear solution. This solution was gradually added to a solution of 16.3g (0.1 mol) phenyl-2-nitropropene in THF at room temperature. A slightly exothermic reaction ensued, and the reaction mixture was stirred for 30 min, a saturated sodium chloride solution was added, and the solution was extracted with ether and the pooled extracts were evaporated under vacuum to give essentially pure P2P oxime in 80% yield. 

The acetonitrile and mercuric nitrate amounts remain the same except they are to be accompanied by 12.6g of fuming nitric acid (see chemicals section) in the reaction flask. Then, with cooling, the safrole or allylbenzene is added just like before. The reaction is immediate and takes no more than 20 minutes of stirring after which lOOmL ice cold dH20 is slowly added. Next, with vigorous stirring, saturated sodium chloride solution is slowly added until a pronounced precipitate forms. This yellowish mass is the chloride. 

The combined organic solutions were washed five times with saturated sodium chloride solution and subsequently dried Over magnesium sulfate. After concentration of the extract in a water-pump vacuum the residue was distilled through... 

Sodium chloride has long been used as a shale stabilizer because of low cost, wide availabiUty, and its presence in many subsurface formations. The inhibitive nature of salt muds increases as the salt content increases from seawater to saturated sodium chloride. In addition to the sodium chloride consumed aimuaHy for drilling fluid, considerable quantities are incorporated while drilling salt zones. This material has been used more for minimizing washouts in salt zones than for stabilizing shales. High salt levels have found appHcation in deep water drilling (7). 

The dependence of solubility on temperature affects the mode of crystallization. For example, Figure 4 shows that the solubiUty of potassium nitrate is strongly influenced by the system temperature but that temperature has Httle influence on the solubiUty of sodium chloride. As a consequence, a reasonable yield of KNO crystals can be obtained by cooling a saturated feed solution on the other hand, cooling a saturated sodium chloride solution accomplishes Httle crystallization, and evaporation is required to increase the yield of sodium chloride crystals. 

A total of 3 g (0.13 moles) of sodium hydride is added to a solution consisting of 10 g of 17 -hydroxy-5a-androstan-3-one (36 mmoles) in 200 ml of benzene and 10 ml of ethyl formate. The reaction mixture is allowed to stand under nitrogen for 3 days followed by dropwise addition of 10 ml of methanol to decompose the excess of sodium hydride. The solution is then diluted with 300 ml water and the layers are separated. The basic aqueous solution is extracted with ether to remove neutral material. The aqueous layer is acidified with 80 ml of 3 A hydrochloric acid and the hydroxymethylene steroid is extracted with benzene and ether. The combined organic extracts are washed with water and saturated sodium chloride solution and then dried over magnesium sulfate and concentrated. The residue, a reddish-yellow oil, crystallized from 10 ml of ether to yield 9.12 g (83%) of 17 -hydroxy-2-hydroxymethylene-5a-androstan-3-one mp 162-162.5°. Recrystallization from chloroform-ether gives an analytical sample mp 165-165.5° [a]o 53° (ethanol) 2 ° 252 mjj. (g 11,500), 307 m u (e 5,800). 

A mixture consisting of 0.69 g (10.5 mmoles) of zinc-copper couple, 12 ml of dry ether, and a small crystal of iodine, is stirred with a magnetic stirrer and 2.34 g (0.7 ml, 8.75 mmoles) of methylene iodide is added. The mixture is warmed with an infrared lamp to initiate the reaction which is allowed to proceed for 30 min in a water bath at 35°. A solution of 0.97 g (2.5 mmoles) of cholest-4-en-3/ -ol in 7 ml of dry ether is added over a period of 20 min, and the mixture is stirred for an additional hr at 40°. The reaction mixture is cooled with an ice bath and diluted with a saturated solution of magnesium chloride. The supernatant is decanted from the precipitate, and the precipitate is washed twice with ether. The combined ether extracts are washed with saturated sodium chloride solution and dried over anhydrous sodium sulfate. The solvent is removed under reduced pressure and the residue is chromatographed immediately on 50 g of alumina (activity III). Elution with benzene gives 0.62 g (62%) of crystalline 4/5,5/5-methylene-5 -cholestan-3/5-ol. Recrystallization from acetone gives material of mp 94-95° Hd -10°. 

The residue (12 g) which contains the 18-iodo-18,20-ether is dissolved in 200 ml of acetone, 5 g of silver chromate is added Note 3) and after cooling to 0°, 11.8 ml of a solution of 13.3 g of chromium trioxide and 11.5 ml of concentrated sulfuric acid, diluted to 50 ml with water is added during a period of 5 min. After an additional 60 min, a solution of 112 g of sodium acetate in 200 ml of water is added and the mixture diluted with benzene (400 ml), filtered and the benzene layer separated. The aqueous phase is reextracted with benzene, washed with half-saturated sodium chloride solution, dried and evaporated to yield 11.2 g of a crystalline residue. Recrystallization from ether gives 7.2 g (72%) of pure 3/5, 1 la, 20/5-trihydroxy-5a-pregnan-18-oic acid 18,20 lactone 3,11-diacetate mp 216-218°. 

P-Hydroxy-A-norpregn-3(5)-en-2-one (7) A solution of the hydroxy-methylene steroid (5) (24.8 g) dissolved in 240 ml of acetic acid and 240 ml of ethyl acetate is ozonized at — 10° with one molar equivalent of ozone. The resulting solution is diluted with 240 ml. of water and 60 ml of 30 % hydrogen peroxide and allowed to stand overnight. The solution is diluted with 1.5 liters of water and extracted with 3 x 700 ml portions of ethyl acetate. The combined extracts are washed with water, saturated sodium chloride solution, dried over sodium sulfate and concentrated to dryness under vacuum, leaving 23.4 g of a colorless amorphous residue of crude diacid. This material shows a maximum in the ultraviolet spectrum at 224 mp (s 6,400) indicating a 53 % yield of unsaturated acid (6). It is used without further purification. 

The mixture is decanted into an Erlenmeyer flask, the residual green salts are washed with two 15-ml portions of acetone, and the washings are added to the main acetone solution. Cautiously, sodium bicarbonate (approx. 13 g) is added to the solution with swirling until the pH of the reaction mixture is neutral. The suspension is filtered, and the residue is washed with 10-15 ml of acetone. The filtrate is transferred to a round-bottom flask and concentrated on a rotary evaporator under an aspirator while the flask temperature is maintained at about 50°. The flask is cooled and the residue transferred to a separatory funnel, (If solidification occurs, the residue may be dissolved in ether to effect the transfer.) To the funnel is added 100 ml of saturated sodium chloride solution, and the mixture is extracted with two 50-ml portions of ether. The ether extracts are combined, washed with several 5-ml portions of water, dried over anhydrous magnesium sulfate, and filtered into a round-bottom flask. The ether may be distilled away at atmospheric pressure (steam bath) or evaporated on a rotary evaporator. On cooling, the residue should crystallize. If it does not, it may be treated with 5 ml of 30-60° petroleum ether, and crystallization may be induced by cooling and scratching. The crystalline product is collected by filtration and recrystallized from aqueous methanol. 4-r-Butylcyclohexanone has mp 48-49° (yield 60-90 %). 

A solution of 12.5 g (0.088 mole) of l,4-dioxaspiro[4.5]decane (Chapter 7, Section IX) in 200 ml of anhydrous ether is added to the stirred mixture at a rate so as to maintain a gentle reflux. (Cooling in an ice bath is advisable.) The reaction mixture is then refluxed for 3 hours on a steam bath. Excess hydride is carefully destroyed by the dropwise addition of water (1-2 ml) to the ice-cooled vessel until hydrogen is no longer evolved. Sulfuric acid (100 ml of 10% solution) is now added followed by 40 ml of water, resulting in the formation of two clear layers. The ether layer is separated and the aqueous layer extracted with three 20-ml portions of ether. The combined ethereal extracts are washed with saturated sodium bicarbonate solution followed by saturated sodium chloride solution. The ethereal solution is dried over anhydrous potassium carbonate (20-24 hours), filtered, and concentrated by distillation at atmospheric pressure. The residue is distilled under reduced pressure affording 2-cyclohexyloxy-ethanol as a colorless liquid, bp 96-98°/ 3 mm, 1.4600-1.4610, in about 85% yield. 

---