Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Sample preparation liquid extraction from solid

Generally, preconcentration of pollutants from water samples and sample preparation steps are accomplished by extraction techniques based on enrichment of liquid phase (liquid/liquid extraction) or solid phase (solid/liquid extraction) ". Historically, liq-uid/liquid extraction (LEE) was used exclusively to enrich phenols from water samples. LEE is still used as a preconcentration step . However, there is an increasing tendency to replace LEE by solid phase extraction (SPE) and solid phase microextraction (SPME). Among the reasons for replacing LEE are foam formation, the large volume of organic solvents needed, the length of the analysis time and difficulties in the automation of LEE procedures. On the other hand, SPE requires incomparable smaller amounts of solvents (SPME requires no solvent at all) and can be easily automated . Finally, SPE and SPME are cheaper in comparison with LEE. [Pg.1353]

Eiquid- or solid-phase extraction methods have been adopted for the isolation of catecholamines and their metabolites from urine samples. The liquid extraction system is ordinarily based on the formation of a complex, in alkaline medium, between diphenylborate and the diol group in the catecholamines. However, the liquid extraction methods reported in the literature are relatively tedious and often involved multiple extraction steps.For the more widely used solid-phase extraction methods, catecholamines may be selectively isolated from the urine sample by adsorption with activated alumina," " phenylboronic acid or cation-exchange resins. All the specimen preparative procedures are specific for the free catecholamines, i.e. the extracted catecholamines do not include the conjugated fraction. [Pg.107]

Ultrasonic LSE is most applicable to the isolation of semivolatile and nonvolatile organic compounds from solid matrices such as soil, sediment, clays, sand, coal tar, and other related solid wastes. U-LSE is also very useful for the disruption of biological material such as serum or tissue. U-LSE can be coupled with solid-phase extraction (SPE) to give a very robust sample preparation method at relatively low cost in comparison to MAE and ASE approaches. The author has utilized U-LSE/SPE to isolate and recover 9,10-dimethyl-l,2-benzanthracene from animal bedding. A 89% recovery was obtained for bedding that was spiked with this polycyclic aromatic hydrocarbon (PAH) of interest to toxicologists (20). An ultrasonic horn and tip are immersed into a mixture of liquid extractant and solid sample and sonicated at some percent of full power for a finite length of time, either continuously or pulsed. [Pg.104]

Proper sampling procedures have to be applied to obtain representative samples from analyzed biological material since mycotoxins are not homogenously distributed in contaminated grain stocks. Sample preparation usually involves a few cleanup steps to eliminate compounds present in the matrix that might coelute with the mycotoxins. The cleanup methods may involve either liquid-liquid extraction (LLE), solid-phase extraction (SPE) on columns that contain various types of solid phases, or immunoaffinity columns [39,42,43]. The recovery achieved with a cleanup method is critical for the final results. [Pg.537]

Theoretical and applied aspects of microwave heating, as well as the advantages of its application are discussed for the individual analytical processes and also for the sample preparation procedures. Special attention is paid to the various preconcentration techniques, in part, sorption and extraction. Improvement of microwave-assisted solution preconcentration is shown on the example of separation of noble metals from matrix components by complexing sorbents. Advantages of microwave-assisted extraction and principles of choice of appropriate solvent are considered for the extraction of organic contaminants from solutions and solid samples by alcohols and room-temperature ionic liquids (RTILs). [Pg.245]

Solubilizing all or part of a sample matrix by contacting with liquids is one of the most widely used sample preparation techniques for gases, vapors, liquids or solids. Additional selectivity is possible by distributing the sample between pairs of immiscible liquids in which the analyte and its matrix have different solubilities. Equipment requirements are generally very simple for solvent extraction techniques. Table 8.2 [4,10], and solutions are easy to manipulate, convenient to inject into chromatographic instruments, and even small volumes of liquids can be measured accurately. Solids can be recovered from volatile solvents by evaporation. Since relatively large solvent volumes are used in most extraction procedures, solvent impurities, contaminants, etc., are always a common cause for concern [65,66]. [Pg.891]

Principles and Characteristics Solid-phase extraction (SPE) is a very popular sample preparation and clean-up technique. In SPE solutes are extracted from a liquid (or gaseous) phase into a solid phase. Substances that have been extracted by the solid particles can be removed by washing with an appropriate liquid eluent. Usually, the volume of solvent needed for complete elution of the analytes is much smaller (typically < 1 mL) than the original sample volume. A concentration of the analytes is thus achieved. [Pg.124]

Miniaturisation of scientific instruments, following on from size reduction of electronic devices, has recently been hyped up in analytical chemistry (Tables 10.19 and 10.20). Typical examples of miniaturisation in sample preparation techniques are micro liquid-liquid extraction (in-vial extraction), ambient static headspace and disc cartridge SPE, solid-phase microextraction (SPME) and stir bar sorptive extraction (SBSE). A main driving force for miniaturisation is the possibility to use MS detection. Also, standard laboratory instrumentation such as GC, HPLC [88] and MS is being miniaturised. Miniaturisation of the LC system is compulsory, because the pressure to decrease solvent usage continues. Quite obviously, compact detectors, such as ECD, LIF, UV (and preferably also MS), are welcome. [Pg.726]

Sample preparation for analysis by hyphenated methods requires some additional planning when compared to nonhyphenated methods. All steps, extraction, concentration, and final solvent selection must take into consideration and be compatible with all the components of the hyphenated instrumentation. For gas chromatographic methods, all the components in the mixture must be in the gaseous state. For liquid chromatography (LC) or high-performance liquid chromatography (HPLC), the samples of the analytes of interest can be solids or liquids, neutral or charged molecules, or ions, but they must be in solution. If the follow-on analysis is by MS, then each of the analytes may require a different method of introduction into the MS. Metals and metal ions may be introduced by HPLC if they are in solution but commonly are introduced via AAS or inductively coupled plasma (ICP). Other analytes may be directly introduced from HPLC to MS [2],... [Pg.324]


See other pages where Sample preparation liquid extraction from solid is mentioned: [Pg.113]    [Pg.1245]    [Pg.104]    [Pg.275]    [Pg.888]    [Pg.499]    [Pg.230]    [Pg.150]    [Pg.8]    [Pg.125]    [Pg.103]    [Pg.2926]    [Pg.1319]    [Pg.1920]    [Pg.145]    [Pg.512]    [Pg.816]    [Pg.492]    [Pg.29]    [Pg.53]    [Pg.372]    [Pg.586]    [Pg.2004]    [Pg.378]    [Pg.522]    [Pg.149]    [Pg.194]    [Pg.351]    [Pg.17]    [Pg.307]    [Pg.902]    [Pg.904]    [Pg.24]    [Pg.52]    [Pg.438]    [Pg.204]    [Pg.35]    [Pg.280]    [Pg.301]    [Pg.320]    [Pg.323]    [Pg.312]   


SEARCH



Extraction from solid

Extraction, sample preparation

Extraction, sampling

Liquid extraction from solid

Liquid preparations

Liquid samples

Liquid-solid extraction

Sample extract

Sample extraction

Sample preparation liquid-solid

Sample preparation liquids

Sample preparation solid samples

Sample solid samples

Sampling extractive

Sampling solids

Solid-liquid samples

© 2024 chempedia.info