Requirements precipitation

Mundell JA, Hill KR, Weaver JW II. 1989. In situ case history Leachable lead required precipitation immobilization. Hazardous Waste Management 23-27. 

The composition of the polysulfide varies. It is generally applied in excess with the result that the final dye is wholly or partly in solution in leuco form. At this stage, it can be converted to a liquid form by suitable dilution and the addition of sodium hydrosulfide or diluted, if necessary filtered, and then precipitated by blowing air through the liquor or adding dilute acid. When stronger dyes are required, precipitation may be carried out by adding... 

The crystalline a-FeOOH-nuclei are very small and can be used as transparent pigments. Pigments with covering properties are obtained by crystal growth on the a-FeOOH nuclei, by adding iron sulfate solution, sodium hydroxide and air, to obtain the particle size corresponding to the hue required (precipitation process). 

Precipitated sihca is an eflective rubber reinforcing filler and can be used to replace carbon black when non-black rubber compounds are required. Precipitated silica is used as a reinforcing aid in butyl caulks and tapes... 

SNG Substitute natural gas. soaps Sodium and potassium salts of fatty acids, particularly stearic, palmitic and oleic acids. Animal and vegetable oils and fats, from which soaps are prepared, consist essentially of the glyceryl esters of these acids. In soap manufacture the oil or fat is heated with dilute NaOH (less frequently KOH) solution in large vats. When hydrolysis is complete the soap is salted out , or precipitated from solution by addition of NaCl. The soap is then treated, as required, with perfumes, etc. and made into tablets. 

Why is potassium aluminium sulphate not soluble in benzene A compound M has the composition C = 50.0% H=12.5%o A1 = 37.5%. 0.360 g of M reacts with an excess of water to evolve 0.336 1 of gas N and leave a white gelatinous precipitate R. R dissolves in aqueous sodium hydroxide and in hydrochloric acid. 20 cm of N require 40 cm of oxygen for complete combustion, carbon dioxide and water being the only products. Identify compounds N and R, suggest a structural formula for M, and write an equation for the reaction of M with water. (All gas volumes were measured at s.t.p.)... 

For temporary hardness due to magnesium carbonate, more lime is required, since the magnesium precipitates as the hydroxide (less soluble than the carbonate) ... 

A compound of cobalt has the formula Co(NH3)jtCl. 0.500 g of it was dissolved in 50.00 cm M hydrochloric acid the excess acid required 40.00 cm M sodium hydroxide solution to neutralise it. Another 0.500 g portion of the compound was dissolved in water and allowed to react with excess silver nitrate solution. 0.575 g of silver chloride was precipitated. 

Remove 25 ml. by means of a pipette, add a few drops of phenolphthalein the colour is pink. Now add very cautiously, drop by drop, dilute acetic acid (say Mjioo) until the pink colour has just not disappeared. It is important not to add too much acid, otherwise the casein will be precipitated. Now add 5 ml. of neutralised formalin (see p. 464) and then titrate with Mj 10 NaOH solution. Note the amount required. 

Ammoniacal Silver Nitr. te. Add 1 drop of 10% aqueous NaOH solution to about 5 ml. of silver nitrate solution in a test-tube then add dilute NHg drop by drop with shaking until only a trace of undissolved Ag O remains. A number of reductions require the presence of Ag " ions. It is often advisable, therefore, after adding the ammonia to add silver nitrate solution until a faint but permanent precipitate is obtained. The solution should always be prepared in small quantities immediately before use, and any unexpended solution thrown away afterwards. If the solution is kept for some time, it may form explosive by-products. 

Prepare a saturated solution of sodium bisulphite at the laboratory temperature from 40 g. of finely powdered sodium bisulphite about 70 ml. of water are required. Measure the volume of the resulting solution and treat it with 70 per cent, of its volume of rectified spirit (or methylated spirit) add sufficient water (about 45 ml.) to just dissolve the precipitate which separates. Introduce 20 g. of commercial cycZohexanone into the aqueous-alcoholic bisulphite solution with stirring and allow the mixture to stand for 30 minutes stir or shake occasionally. FUter off the crystalline bisulphite compound at the pump, and wash it with a little methylated spirit. 

Dissolve (or suspend) 0-25 g. of the acid in 5 ml. of warm water, add a drop or two of phenolphthalein indicator and neutralise carefully with ca. N sodium hydroxide solution. Then add 2-3 drops of ca. O lN hydrochloric acid to ensure that the solution is almost neutral (pale pink colour). (Under alkaline conditions the reagent tends to decompose to produce the evil-smelling benzyl mercaptan.) If the sodium salt is available, dissolve 0-25 g. in 5 ml. of water, and add 2 drops of ca. 0 -hydrochloric acid. Introduce a solution of 1 g. of S-benzyl-iso-thiuro-nium chloride in 5 ml. of water, and cool in ice until precipitation is Dibasic and tribasic acids will require 0-01 and 0-015 mol respectively. 

To 5 ml. of water add 1-2 drops of the amine if the amine does not dissolve, add a drop or two of concentrated hydrochloric acid. Add 0-5-1 ml. of this amine solution to 2-3 ml. of the reagent an almost immediate precipitate indicates the presence of a primary amine. A slight turbidity indicates the presence of a primary amine as an impurity. (Primary aromatic amines generally require 2-3 minutes for the test. Urea and other amides, as well as amino acids, do not react.)... 

Method 1. From ammonium chloroplatinate. Place 3 0 g. of ammonium chloroplatinate and 30 g. of A.R. sodium nitrate (1) in Pyrex beaker or porcelain casserole and heat gently at first until the rapid evolution of gas slackens, and then more strongly until a temperature of about 300° is reached. This operation occupies about 15 minutes, and there is no spattering. Maintain the fluid mass at 500-530° for 30 minutes, and allow the mixture to cool. Treat the sohd mass with 50 ml. of water. The brown precipitate of platinum oxide (PtOj.HjO) settles to the bottom. Wash it once or twice by decantation, filter througha hardened filter paper on a Gooch crucible, and wash on the filter until practically free from nitrates. Stop the washing process immediately the precipitate tends to become colloidal (2) traces of sodium nitrate do not affect the efficiency of the catalyst. Dry the oxide in a desiccator, and weigh out portions of the dried material as required. 

---