Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Propellant types

Cup anemometers have shaped cups mounted on the spokes of a wheel. The cups, under the action of the fluid forces, spin in a horizontal plane about a vertical shaft mounted in bearings. Vane or propeller types use a multibladed rotor, the axis of which is parallel to the flow direction as the rotating member. Both designs are commonly used for wind speed measurement or similar appHcations such as the velocity in ventilation ducts. Because of inertia, anemometers are most accurate under steady conditions. Velocity fluctuations cause readings that are too high. [Pg.63]

Axial-Plow Propeller-Type. The axial-flow propeUer-type pumps are used to handle large volumes of pumped Hquid at low head. Flow rates of >12 m /s (>200,000 gal/min) can be accommodated. [Pg.293]

Axial-Plow Propeller-Type. For high capacity, single-stage propeller-type vertical pumps are used. One appHcation of this design is as an intake of cooling water from a river or a hoi ding basin via a pipeline. [Pg.295]

Recent developments in cooling-tower fan energy management also include automatic variable-pitch propeller-type fans and inverter-type devices to permit variable fan speeds. These schemes involve tracking the loaa at a constant leaving-water temperature. [Pg.1166]

FIG. 14-103 Propeller-type surface aerator. (Ashhi ook-Simon-Haiiley Coip.)... [Pg.1424]

Side entering mixers are used for blending pui-poses. The side entering propeller type mixer is economical and establishes an effective flow pattern in almost any size tank. Because the shaft seal is below the liquid level, its use in fluids without corrosive and erosive properties is usually ideal. [Pg.207]

The flask should have creased sides and a conical indentation in the bottom and should be equipped with a high-speed, propeller-type stirrer rotated to force the liquid downwards. The stirrer should be constructed of glass because metals may interfere with the generation and utilization of the hydroxyl free radicals. [Pg.91]

Pitot ube or Pitot Venturi Tube Turbine or Propeller Type Element Rotameter... [Pg.21]

Figure 3-10. Vertical propeller type pump. (Courtesy Peerless Pump Div., FMC Corp.)... Figure 3-10. Vertical propeller type pump. (Courtesy Peerless Pump Div., FMC Corp.)...
For general service, the fans are axial flow, propeller type with 2-20 blades per fan which force or induce the air across the bundle. Four blades are considered minimum, and an even number of blades (2-20) are preferable to an odd... [Pg.254]

Fans, propeller type—starting with discharge valve open 30 100 150 5-60... [Pg.632]

Figure 38.2 Side-entering propeller-type mixer... Figure 38.2 Side-entering propeller-type mixer...
Installation of propeller-type mixers varies greatly, depending on the specific application. Top-entering mixers utilize either a clamp- or flange-type mounting. It is important that the mixer be installed so the propeller or paddle placement is at a point within the tank, vessel, or piping that assures proper mixing. Vendor recommendations found in O M manuals should be followed to ensure proper operation of the mixer. [Pg.570]

NMR spectra show the ethene molecules to undergo a propeller type rotation about the metal-alkene axis the fluxionality is removed on cooling such rotation is not observed with coordinated C2F4, indicating a higher barrier to rotation, in keeping with the stronger Rh—C bonds [66]. [Pg.104]

Use well-designed, specialized polymer dissolution systems wherever possible (such as those from the U.S. Filter, Inc. subsidiary, Strandco ), especially for emulsion polymers, rather than simple dissolving tanks and mixers with propeller-type impellers. This prevents undissolved lumps of polymer (fish-eyes) and the breakdown of polymer chains. Always install a strainer to prevent possible pump clogging. [Pg.319]

One extremely important point to realize is that different propellant types may have different rate-controlling processes. For example, the true double-base propellants are mixed on a molecular scale, since both fuel and oxidizing species occur on the same molecule. The mixing of ingredients and their decomposition products has already occurred and can therefore be neglected in any analysis. On the other hand, composite and composite modified-double-base propellants are not mixed to this degree, and hence mixing processes may be important in the analysis of their combustion behavior. [Pg.31]

Ag-309 to Ag-312 4 Agitators for hold tank, propeller type, 50 hp. Stainless steel. [Pg.118]

One way to estimate prices of items when they cannot be found is to compare them with other items that might be similar or to items that might be expected to cost about the same. To be conservative for the cutter, it was assumed that a blender would cost at least as much and probably more. Its price was equated to that of a similar size blender ( 5,000). In place of an anchor-type agitator, the costs for a propeller-type agitator was used. Similarly, it was assumed that an epoxy-lined tank would cost the same as a rubber-lined tank. [Pg.265]

The turbine turns a generator to produce electricity [22], A variety of turbines may be used, including a Pelton wheel for high head, low-flow water supply, or a propeller-type turbine for low-head installations [24, 25]. [Pg.49]

A wide-mouth 1-1. Erlenmeyer flask is supported inside a water bath of at least 2-1. capacity so that the bottom of the flask is not in contact with the bottom of the bath. The bath is filled with water at about 15° to cover at least half the height of the flask. The flask is fitted with a moderate-speed stainless-steel propeller-type stirrer, and 350 ml. of nitric acid (sp. gr. 1.4) at 20° is poured into it. Veratraldehyde,2 70 g. (0.42 mole) (Note 2), is crushed at least as fine as rice grains and is slowly added in small portions to the acid. The rate of addition should be such that it requires about 1 hour to add all the aldehyde. It is helpful, although not usually necessary, to add two or three ice cubes to the bath at the start of the nitration. The internal temperature is chocked from time to time and should be held between 18°... [Pg.93]

Chain propagation is started from a methylene group and terminated by desorption of 1-alkenes or alkanes. Propeller-type mobility of the olefin ligand renders possible CH3 branching of the growing chain, as demonstrated by the scheme. The growth probability is determined by the ratio of rates of formation of the alkyl intermediate and of the desorption of 1-alkenes, and to a minor extent of alkanes. [Pg.209]

Axial flow impellers, 16 672-673, 684 Axial-flow propeller-type pumps, 22 67, 68 Axially split pumps, 22 67, 68 Axial Peclet number, 10 763 Axial undulations, in hemodialysis, 26 830-831... [Pg.81]

According to these simulations, the dendrimers based on core 10 adopt a false-propeller structure, while the dendrimers based on the hexaphenyl-benzene core 11 adopt a true-propeller type structure. The difference lies in... [Pg.17]

Zinc dust (Zn) is not a compound but a gray powder that is used as a pigment and acts as an excellent reducing agent and catalyst. It is dangerous because it can explode when exposed to moist air and may heat up and ignite spontaneously. When mixed with dry, powdered sulfur, it makes an excellent dry propellant-type rocket fuel, but is dangerous to handle. [Pg.116]

Carbanions of the type [HjCR ], [HCR R ] and [CR R R ] (R = NO and R R = CN, NO, NO2) can be considered to be resonance-stabilized, nonlinear pseudohalides. All experimentally known resonance-stabilized methanides are reported to be planar or nearly planar (Table 1). While the parent ion, the methanide anion HsC, adopts a pyramidal structure [Afipianar-pyramidai = 9.8 kJmol rf(CH) = 1.099 A, <(HCH) = 109.7° cf. rf(CH) = 1.093 A, <(HCH) = 109.6°] due to the lack of delocalization (no resonance for the p-AO-type lone pair possible) , substitution of one H atom by NO results in a planar anion since the empty jr -orbitals of the NO group are perfectly suitable to delocalize the carbon lone pair. Further substitution of the second H atom again results in planar anions, and the same holds for the third substitution in case of R = CN. In case of R = NO and NO2, the third substitution leads either to a propeller-type structure with only a small distortion from planarity or one NO2 group is twisted by 90°, nevertheless leaving the central carbon in an almost trigonal planar environment . ... [Pg.696]

The so-called propeller-type fans with blades that are aerodynami-cally designed (as seen in Fig. 10-83) can consist of two or more stages. The air in these fans enters in an axial direction and leaves in an axial direction. The fans usually have inlet guide vanes followed by a rotating blade, followed by a stationary (stator) blade. [Pg.49]


See other pages where Propellant types is mentioned: [Pg.49]    [Pg.230]    [Pg.1195]    [Pg.1422]    [Pg.65]    [Pg.2]    [Pg.79]    [Pg.463]    [Pg.559]    [Pg.1269]    [Pg.292]    [Pg.541]    [Pg.551]    [Pg.569]    [Pg.292]    [Pg.884]    [Pg.32]    [Pg.81]    [Pg.62]    [Pg.772]    [Pg.772]    [Pg.44]    [Pg.495]   
See also in sourсe #XX -- [ Pg.169 ]




SEARCH



Agitators propeller-type

Double base propellant solvent type

Mixers propeller type

Propeller-type impellers

Propeller-type structures

© 2024 chempedia.info