Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Axial Splitting

The theory of bent beams shows that variable curvature is accommodated by shear stresses, which are a maximum on the central plane. In fibres undergoing flex fatigue the.se shear stresses can cause failure by axial splitting. Fig. lOf.g. [Pg.68]

b) Polye.sler fibres after a single bend, (c-e) Flex fatigue in polyester kink-band fracture, (f) Flex fatigue shear splitting in nylon, (g) Flex fatigue shear splitting in polyester. For further explanation. [Pg.68]

Fig. 8. Single-stage between-bearings double-suction pumps (a) axially split design and (b) radially split design. Fig. 8. Single-stage between-bearings double-suction pumps (a) axially split design and (b) radially split design.
Whole Vessel Driven by an Inert Ideal Gas Escaping through Axial Split... [Pg.2281]

Centrifugal compressor cases are classified as horizontally split or vertically split (Figures 12-40A-C). The 5th Edition, April, 1988, API Standard 617 refers to the horizontally split style as Axial Split and vertically split units as Radial Split The first terminology is more standard than that of the API-617. Figure 12-40D illustrates one flow arrangement for back-to-back internal flow, with the following advantages ... [Pg.456]

Centrifugal pumps can be further classified by physical design or axially split, radially split and whether the axis of rotation of the impeller(s) is vertical or horizontal. [Pg.473]

Axial flow impellers, 16 672-673, 684 Axial-flow propeller-type pumps, 22 67, 68 Axially split pumps, 22 67, 68 Axial Peclet number, 10 763 Axial undulations, in hemodialysis, 26 830-831... [Pg.81]

Dimensions to tolerance grade H7/h6 for axially split pumps, an additional tolerance to allow for gasket thickness + 75 pm / 0.003 in. [Pg.29]

Seal glands shall be provided with bolt holes rather than slots, except where the ease of dismantling pumps with axially split casings makes slotted construction desirable. [Pg.30]

Axially split casings may have a composition sheet gasket or a metal-to-metal joint the vendor s bid shall state which is being offered. [Pg.58]

The liners, pads, or shells shall be in axially split housings and shall be replaeeable without having to dismantle any portion of the easing or remove the eoupling hub. [Pg.60]

Axially split bearing housings shall have a metal-to-metal split joint whose halves are located by means of cylindrical dowels. [Pg.60]

If pumps with axially split casings are furnished, a sheet gasket suitable for the service is acceptable. Spiral wound gaskets should contain a filler matrial suitable for the service. [Pg.131]

BB1 axially split/1 or 2 stages BB2 radially split/1 or 2 stage BB3 axially split/multistage BB4 single case/radially split/multistage BB5 double case/radlally split/multistage VERTICAL SUSPENDED TYPE ... [Pg.183]

The EPR powder spectra of the low-spin complexes [0s(NH3)5L][CF3S03]3 (L = H20 or (5)) have been analyzed the negative sign obtained for the axial splitting when L = (5) has been rationalized in terms of Os L backbonding. Crystal field parameters have also been derived. The spectral and electrochemical properties of [Ru(NH3)5L]" (Ru or Ru L =RC02 R = 4-py-A-Me+ or L = RCONH R = Ph, 4-py-A-Me", 4-py-A-H+) have been studied in detail as a function of pH the carboxamido Ru complexes are weak bases and are deprotonated only in strongly acidic solution. ... [Pg.557]

Maximum casing working pressure for axially split compressors (psig) is... [Pg.69]

Axially-split one-and two-stage between-bearings pumps shall be designated pump type BB1. [Pg.23]

The axial splitting parameter Aax (which is positive when the A-term is the ground state),... [Pg.55]

The axial splitting parameter is Aax < 0 when the ground Eg term arises from the splitting of the octahedral T-term then Aax > 0 applies when the ground state is either A- or fi-type. [Pg.262]

Types 1 and 4 tensile failures, which are of less interest to conservationists at this time, are caused by brittle crack propagation and by long axial splits, respectively. Such fractures can occur in ceramic and elastomeric fibers (both Type 1) and highly oriented aramids (Type 4). [Pg.86]

See other pages where Axial Splitting is mentioned: [Pg.2264]    [Pg.371]    [Pg.183]    [Pg.206]    [Pg.11]    [Pg.12]    [Pg.14]    [Pg.14]    [Pg.21]    [Pg.41]    [Pg.58]    [Pg.128]    [Pg.11]    [Pg.11]    [Pg.14]    [Pg.34]    [Pg.35]    [Pg.68]    [Pg.87]    [Pg.140]    [Pg.144]    [Pg.9]    [Pg.219]    [Pg.88]    [Pg.103]    [Pg.104]   


SEARCH



© 2024 chempedia.info