Pressure developed

The criterion retained up to now in the specifications is not the true vapor pressure, but an associated value called the Reid vapor pressure, RVP. The procedure is to measure the relative pressure developed by the vapors from a sample of motor fuel put in a metallic cylinder at a temperature of 37.8°C. The variations characteristic of the standard method are around 15 millibar in repeatability and 25 millibar in reproducibility. 

Except for gases, it is very difficult to detennine Cy. For a solid or liquid the pressure developed in keeping the volume constant when the temperature is changed by a significant amount would require a vessel so massive that most of the total heat capacity would be that of the container. It is much easier to measure the difference... 

Method 2. Place a 3 0 g. sample of the mixture of amines in a flask, add 6g. (4-5 ml.) of benzenesulphonyl chloride (or 6 g. of p-toluenesulphonyl chloride) and 100 ml. of a 5 per cent, solution of sodium hydroxide. Stopper the flask and shake vigorously until the odour of the acid chloride has disappeared open the flask occasionally to release the pressure developed by the heat of the reaction. AUow the mixture to cool, and dissolve any insoluble material in 60-75 ml. of ether. If a solid insoluble in both the aqueous and ether layer appears at this point (it is probably the sparingly soluble salt of a primary amine, e.g., a long chain compound of the type CjH5(CH2) NHj), add 25 ml. of water and shake if it does not dissolve, filter it off. Separate the ether and aqueous layers. The ether layer will contain the unchanged tertiary amine and the sulphonamide of the secondary amine. Acidify the alkaline aqueous layer with dilute hydrochloric acid, filter off the sulphonamide of the primary amine, and recrystaUise it from dilute alcohol. Extract the ether layer with sufficient 5 per cent, hydrochloric acid to remove all the tertiary amine present. Evaporate the ether to obtain the sulphonamide of the secondary amine recrystaUise it from alcohol or dilute alcohol. FinaUy, render the hydrochloric acid extract alkaline by the addition of dilute sodium hydroxide solution, and isolate the tertiary amine. 

The pressure developed by decomposition of acetylene in a closed container depends not only on the initial pressure (or more precisely, density), but also on whether the flame propagates as a deflagration or a detonation, and on the length of the container. For acetylene at room temperature and pressure, the calculated explosion pressure ratio, / initial > deflagration and ca 20 for detonation (at the Chapman-Jouguet plane). At 800 kPa (7.93... 

Booster Pump. Use of a centrifugal booster pump avoids a low intake pressure, particularly for large, high volume units. A low pressure (>26.6 kPa (200 mm Hg)) on the iatake of a timing pump can cause vaporization of the product. The booster pump is ia the circuit ahead of the timing pump and operates only when the FDV is ia forward flow, the metering pump is ia operation, and the pasteurized product is at least 7 kPa (1 psi) above the maximum pressure developed by the booster pump (Fig. 8). 

Osmotic Pressure Controlled Oral Tablets. Alza Corp. has developed a system that is dependent on osmotic pressure developed within a tablet. The core of the tablet is the water-soluble dmg encapsulated in a hydrophobic, semipermeable membrane. Water enters the tablet through the membrane and dissolves the dmg creating a greater osmotic pressure within the tablet. The dmg solution exits at a zero-order rate through a laser drilled hole in the membrane. Should the dmg itself be unable to provide sufficient osmotic pressure to create the necessary pressure gradient, other water-soluble salts or a layer of polymer can be added to the dmg layer. The polymer swells and pushes the dmg solution through the orifice in what is known as a push-pull system (Fig. 3). The exhausted dmg unit then passes out of the body in fecal matter. 

Within the bowl, the pressure,, developed also exerts axial separation forces. The internal pressure in a bowl is shown in equation 35 ... 

The energy required to initiate an explosion and the maximum explosive pressure developed by a number of polyester—epoxy powder coatings has been studied in some detail (89). The variables studied included composition, level and type of pigmentation, particle size, and concentration in air. The lowest MEG for unfilled and unpigmented powders was 33—35 g/m. ... 

Motor running backward or impeller of double suction design is mounted backward. Discharge pressure developed in both cases is about one-half design value. 

For dilute concentrations of manv gases and over a fairly wide range for some gases, the equihbrium relationship is given by Henry s law, which relates the partial pressure developed by a dissolved solute A in a liquid solvent B by one of the following equations ... 

Understanding how sudden pressure releases can occur is important. They can happen, for example, from ruptured high-pressure tanks, runaway reactions, flammable vapor clouds, or pressure developed from external fire. The proper design of pressure rehef systems can reduce the possibility of losses from unintended overpressure. 

Pressure Development Overpressure in a UVCE results from turbulence that promotes a sudden release of energy. Tests in the open without obstacles or confining structures do not produce damaging overpressure. Nevertheless, combustion in a vapor cloud within a partially confined space or around turbulence-producing obstacles may generate damaging overpressure. Also, turbulence in a jet release, such as may occur with compressed natural gas discharged from a ruptured pipehne, may result in blast pressure. 

Example The combustion process in large vapor clouds is not known completely and studies are in progress to improve understanding of this important subject. Special study is usually needed to assess the hazard of a large vapor release or to investigate a UVCE. The TNT equivalent method is used in this example other methods have been proposed. Whatever the method used for dispersion and pressure development, a check should be made to determine if any govern-mentaf unit requires a specific type of analysis. 

This is the pressure at the pump discharge nozzle as measured by a gauge. It is equal to the suction pressure plus the total pressure developed by the pump. 

Maximum Pressure and Rate of Pressure Rise and KJ These explosibility parameters are used in assessing whether equipment will contain the maximum pressure developed during deflagration, or to design deflagration relief vents and other explosion prevention systems (see NEPA 68 and 69). The test method is given in ASTM E 1226. 

The degree of reaction, R, in the axial compressor is defined as the ratio of the static differential pressure in the rotor to the static differential pressure developed across the stage. 

Chemical Reactivity - Reactivity with Water No reaction Reactivity with Common Materials Attacks copper and copper alloys these metals should not be used. Penetrates leather, so contaminated leather shoes and gloves should be destroyed. Attacks aluminum in high concentrations Stability During Transport Stable Neutralizing Agents for Acids and Caustics Not pertinent Polymerization May occur spontaneously in absence of oxygen or on exposure to visible light or excessive heat, violently in the presence of alkali. Pure ACN is subject to polymerization with rapid pressure development. The commercial product is inhibited and not subject to this reaction Inhibitor of Polymerization Methylhydroquinone (35 - 45 ppm). 

Calculate individually the orifice area required to pass the unflashed hquid component, using Equation (8). The pressure drop term Pj should be made equal to the set pressure minus the total back pressure developed by the vapor portion at critical flow pressure, except when the critical flow pressure is less than the calculated total back pressure (superimposed plus built-up), considering the combined liquid and vapor flow. In the latter case, P should be made equal to set pressure minus the calculated total back pressure. 

The back pressure developed at the downstream section of any pressure-relief valve connected to the same headers should not exceed the allowable limit, i.e., 10 percent of the set pressure in psig for the conventional type and 40 to 50 percent of the set pressure in psia for the balanced type valve. 

The orifice, the venturi, and the nozzle are instruments for the measurement of duct or pipe flow rate. A constriction, throttling the flow, is placed in the duct, and the resulting differential pressure developed across the constriction is measured. It is the difference in the geometric shape that characterizes the three devices see Fig. 12.22. 

This incident illustrates the dangers of dead-ends and the pressures developed when water is suddenly vaporized. It also shows how easily knowledge can be lost when people leave. Even if the new foreman was told to run the pump all the time or if this was written in the instructions, the reason for doing so might be forgotten, and the circulation might be stopped because it seemed unnecessary or to save electricity. 

Corrosion usually results in a leak or failure of a support because a vessel or support gets too thin. It is then not strong enough to withstand the pressure or load. However, rust can cause failure in another way. It occupies about seven times the volume of the steel from which it was formed. V/hen rust occurs between two plates that have been bolted or riveted together, a high pressure develops. This can force the plates apart or even break the bolts or rivets (see Section 9.1.2 g). Corrosion of the reinforcement bars in concrete can cause the concrete to crack and break away. 

Pressure Piling In a compartmented system in which there are separate but interconnected volumes, the pressure developed by the deflagration in one compartment causes a pressure rise in the unburned gas in the interconnected compartment, so that the elevated pressure in the latter compartment becomes the starting pressure for a further deflagration. This effect is known as pressure piling, or cascading. 

---