Methyl hydrogenation

Dimethyl Sulphate Method for hydroxy compounds and for primary and secondary amines, acid amides, etc. The substance is dissolved or suspended in water, a small excess (above the theoretical) of sodium hydroxide added and then the theoretical quantity of dimethyl sulphate, the mixture being finally shaken without external warming. Methylation is usually rapid, the dimethyl sulphate being converted to methyl hydrogen sulphate... 

Dimethyl sulphate is of particular value for the methylation of phenols and sugars. The phenol is dissolved in a slight excess of sodium hydroxide solution, the theoretical quantity of dimethyl sulphate is added, and the mixture is heated on a water bath and shaken or stirred mechanically (compare Section IV, 104). Under these conditions only one of the methyl groups is utilised the methyl hydrogen sulphate formed in the reaction reacts with the alkali present. -... 

By increasing the molar proportion of the monocarboxylic acid, the yield of (II) is improved. Thus electrolysis of a mixture of decanoic acid (n-decoic acid capric acid) (V) (2 mols) and methyl hydrogen adipate (VI) (1 mol) in anhydrous methanol in the presence of a little sodium methoxide gives, after hydrolysis of the esters formed, n-octadecane (VII), tetradecanoic or myristic acid (VIH) and sebacic acid (IX) ... 

An excellent synthesis of myristic acid is thus achieved from readily accessible starting materials. An alternative synthesis of myristic acid utilises hexanoic acid (M-caproic acid n-hexoic acid) (X) (2 mols) and methyl hydrogen sebacate (XI) (1 mol) the products, after hydrolysis, are Ji-decane (XII), myristic acid (XIII) and hexadecane-1 16-dlcarboxylic acid (XIV) ... 

Sebacic acid. Dissolve 40 g. of methyl hydrogen adipate in 100 ml. of absolute methanol to which 01 g. of sodium has been added. Pass a current of about 2 0 amps, until the pH of the solution is about 8 (ca. 5 hours) test with B.D.H. narrow-range indicator paper. Transfer the contents of the electrolysis cell to a 500 ml. round-bottomed flask, render neutral with a little acetic acid, and distil off the methanol on a water... 

Myristic acid from hexanoic acid and methyl hydrogen sebacate). Dissolve 23 -2 g. of redistilled hexanoic acid (re caproic acid), b.p. 204-6-205-5°/760 mm., and 21-6 g. of methyl hydrogen sebacate in 200 ml. of absolute methanol to which 0 13 g. of sodium has been added. Electrolyse at 2 0 amps., whilst maintaining the temperature between 30° and 40°, until the pH is about 8 0 (ca. 6 hours). Neutralise the contents of the electrolysis cell with a little acetic acid and distil off the methyl alcohol on a water bath. Dissolve the residue in 200 ml. of ether, wash with three 50 ml. portions of saturated sodium bicarbonate solution, once with water, dry with anhydrous magnesium sulphate, and distil with the aid of a fractionating column (see under Methyl hydrogen adipate). Collect the re-decane at 60°/10 mm. (3 0 g.), the methyl myristate at 158-160°/ 10 mm. (12 5g.) and dimethyl hexadecane-1 16-dicarboxylate at 215-230°/ 7 mm. (1 -5 g.)... 

R methyl hydrogen sulfate Organo hydrogen sulfates (RO)3 O JT ... 

The only commercially important dialkyl sulfates are dimethyl sulfate and diethyl sulfate. Estimated worldwide production in 1996 for dimethyl sulfate was 90,000 metric tons per year. Dimethyl sulfate was initially made by vacuum pyrolysis of methyl hydrogen sulfate ... 

Later it was synthesized in a batch process from dimethyl ether and sulfur thoxide (93) and this combination was adapted for continuous operation. Gaseous dimethyl ether was bubbled at 15.4 kg/h into the bottom of a tower 20 cm in diameter and 365 cm high and filled with the reaction product dimethyl sulfate. Liquid sulfur thoxide was introduced at 26.5 kg/h at the top of the tower. The mildly exothermic reaction was controlled at 45—47°C, and the reaction product (96—97 wt % dimethyl sulfate, sulfuhc acid, and methyl hydrogen sulfate) was continuously withdrawn and purified by vacuum distillation over sodium sulfate. The yield was almost quantitative, and the product was a clear, colorless, mobile Hquid. A modified process is deschbed in Reference 94. Properties are Hsted in Table 3. 

The most widely used sUicones are polymers of methyl(hydrogen)sUoxane and of dimethylsiloxane. Polydimethylsiloxane is the basic polymer used in sUicone repeUents. If the polymer is terminated with methyl groups it is inert however, if it is terminated with hydroxyl groups, it can be cross-linked. Continuous, durable coatings result from the use of curable blends of polydimethyl siloxane and polymethyl(hydrogen)sUoxane. The sUicone finish encapsulates individual fibers. 

Pyridinium methiodide, 3-cyano-hydrogen-deuterium exchange, 2, 287 Pyridinium methiodide, 3-methyl-hydrogen-deuterium exchange, 2, 287 Pyridinium methosulfate, l-methoxy-3-methyl-reactions... 

Pyridin-4-one, 1 -hydroxy-2,6-dimethyl-hydrogen-deuterium exchange reactions, 2, 196 Pyridin-4-one, 1-methyl-hydrogen-deuterium exchange, 2, 287 pK 2, 150 Pyridin-2-one imine tautomerism, 2, 158 Pyridin-2-one imine, 1-methyl-quaternization, 4, 503 Pyridin-4-one imine tautomerism, 2, 158 Pyridinone methides, 2, 331 tautomerism, 2, 158 Pyridinones acylation, 2, 352 alkylation, 2, 349 aromaticity, 2, 148 association... 

Pyrrolo[2,3-6]pyridine, 2-methyl-Reimer-Tiemann reaction, 4, 508 Pyrrolo[2,3-6]pyridine, 4-methyl-hydrogen exchange, 4, 502 reaction with aldehydes, 4, 503 reaction with benzaldehyde, 4, 511... 

Triazine, 5-methyl-hydrogen-deuterium exchange, 3, 401 reactions... 

To a solution of 33 g. (O.S mole) of potassium hydroxide (Note 1) in 1.5 1. of distilled water in a 5-1. flask or other appropriate container fitted with a mechanical stirrer is added 80 g. (0.5 mole) of methyl hydrogen adipate (Note 2). With continuous stirring a solution of 85 g. (0.5 mole) of silver nitrate in 1 1. of distilled water is added rapidly (about IS minutes). The precipitated methyl silver adipate is collected on a Buchner funnel, washed with methanol, and dried in an oven at 50-60°. For the next step the dried silver salt is finely powdered and sieved through a 40-mesh screen. The combined yield from two such runs is, 213 g. (80%). 

The methyl hydrogen adipate was Eastman Kodak grade. 

This method with some slight modihcations is applied in the synthesis of to-bromo esters from Cs to Cn. Methyl 5-bromovalerate has been prepared by treating the silver salt of methyl hydrogen adipate with bromine. The ethyl ester has been prepared from the acid by esterification or through the acid chloride. ... 

Entries 11 and 13 in Table 3.4 present data relating the efiect of methyl substitution on methanol and methylamine. The data show an increased response to methyl substitution. While the propane barrier is 3.4 kcal/mol (compared to 2.88 in ethane), the dimethylamine barrier is 3.6kcal/mol (compared to 1.98 in methylamine) and in dimethyl ether it is 2.7 kcal/mol (compared to 1.07 in methanol). Thus, while methyl-hydrogen eclipsing raised the propane barrier by 0.5 kcal/mol, the increase for both dimethylamine and dimethyl ether is 1.6 kcal/mol. This increase in the barrier is attributed to greater van der Waals repulsions resulting from the shorter C—N and C—O bonds, relative to the C—C bond. 

The radical is generated by photolytic decomposition of di-/-butyl peroxide in methylcy-clopropane, a process that leads to selective abstraction of a methyl hydrogen from methylcyclopropane ... 

---