Matrix resin thermosetting resins

Prepreg Fibrous reinforcement held in position with polymeric matrix. May be sheet, tape or, tow. If the matrix is thermoset resin, may be partly cured to induce right level of tack, a condition known as B-stage. 

Based on these excellent performances, aluminum borate whiskers are used not only for thermal insulation material, heat-resistant material, and corrosion-resistant material but also for reinforcing agents in thermoplastic resin, thermosetting resin, ceramics, cement, and metal, and are used mainly to reinforce light metal alloy, ceramic material, resin matrix composite, coatings, and so on. 

The thermoplastic or thermoset nature of the resin in the colorant—resin matrix is also important. For thermoplastics, the polymerisation reaction is completed, the materials are processed at or close to their melting points, and scrap may be reground and remolded, eg, polyethylene, propjiene, poly(vinyl chloride), acetal resins (qv), acryhcs, ABS, nylons, ceUulosics, and polystyrene (see Olefin polymers Vinyl polymers Acrylic ester polymers Polyamides Cellulose ESTERS Styrene polymers). In the case of thermoset resins, the chemical reaction is only partially complete when the colorants are added and is concluded when the resin is molded. The result is a nonmeltable cross-linked resin that caimot be reworked, eg, epoxy resins (qv), urea—formaldehyde, melamine—formaldehyde, phenoHcs, and thermoset polyesters (qv) (see Amino resins and plastics Phenolic resins). 

Currendy, epoxy resins (qv) constitute over 90% of the matrix resin material used in advanced composites. The total usage of advanced composites is expected to grow to around 45,500 t by the year 2000, with the total resin usage around 18,000 t in 2000. Epoxy resins are expected to stiH constitute about 80% of the total matrix-resin-systems market in 2000. The largest share of the remaining market will be divided between bismaleimides and polyimide systems (12 to 15%) and what are classified as other polymers, including thermoplastics and thermoset resins other than epoxies, bismaleimides, cyanate esters, and polyimide systems (see Composites,polymer-matrix-thermoplastics). 

In the narrow sense, bis-maleimide resin means the thermosetting resin eom-posed of the bis-maleimide of methylene dianiline (BMI, bis(4-maleimidophenyl)-methane) and methylene dianiline (MDA, bis(4-aminophenyl)methane) (Fig. 1). Beeause of the addition meehanism, the resin is eured without elimination, whieh is a eharacteristic of this resin. Bis-maleimide resin is used as a thermally stable matrix up to 204°C (400 F) whieh typical epoxy resins may not normally be used. However, in spite of having an imide structure, bis-maleimides are classified as being moderately thermally stable resins. The aliphatic structure of the resin is not stable for long periods above 232°C (450°F.) If a highly aromatic thermally stable thermosetting resin is necessary, acetylene end-capped aromatic imide-based oligomers should be used. 

A substantial effort in our laboratory has been directed toward the synthesis and characterization of acetylene-terminated (AT) matrix resins. The most significant feature and driving force for the effort is that the thermal induced addition reaction provides a moisture Insensitive cured product. This technology offers a wide variety of thermoset resins for various high temperature applications. Backbone structural design for use temperature capabilities, processing characteristics and mechanical performance has demonstrated the versatility of the AT type systems. 

StructurPly I and II by Multi-Axial are thermoplastic matrix resin prepregs used in the construction of primary-load-carrying composite structures. Unlike the few hours typically required by the thermoset resin materials to cure, StructurPly needs a few minutes at 196°C. 

Figure 17 provides an overview of the function of the diazoquinone/novolac materials. The matrix resin is a copolymer of a phenol and formaldehyde. The generic term for this class of polymers is novolac (18) meaning "new lacquer" and describes the purpose for which they were first developed. The chemical industry produces millions of tons of novolac each year where its end use is that of a thermoset resin and adhesive. Novolac is commonly used, for example, as the principle adhesive in the manufacture of plywood. 

Fiber-Matrix Composites. As shown in Figure 1.75, there are two main classifications of FMCs those with continuous fiber reinforcement and those with discontinuous fiber reinforcement. Continuous-flber-reinforced composites are made from fiber rovings (bundles of twisted filaments) that have been woven into two-dimensional sheets resembling a cloth fabric. These sheets can be cut and formed to a desired shape, or preform, that is then incorporated into a composite matrix, typically a thermosetting resin such as epoxy. Metallic, ceramic, and polymeric fibers of specific compositions can all be produced in continuous fashions, and the properties of the... 

The primary resin of interest is epoxy. Carbon-fiber-epoxy composites represent about 90% of CFRP production. The attractions of epoxy resins are that they polymerize without the generation of condensation products that can cause porosity, they exhibit little volumetric shrinkage during cure which reduces internal stresses, and they are resistant to most chemical environments. Other matrix resins of interest for carbon fibers include the thermosetting phenolics, polyimides, and polybismaleimides, as well as high-temperature thermoplastics such as polyether ether ketone (PEEK), polyethersulfone (PES), and polyphenylene sulfide. 

In most applications, polyester and vinyl ester resins are used as the matrix materials. Epoxies are also used, although they require longer cure times and do not release easily from the pultrusion dies. Hence, thermosetting resins are most commonly used with pultrusion, although some high-performance thermoplastics such as PEEK and polysulfone can also be accommodated. In addition to the resin, the resin bath may contain a curing agent (initiator, cf. Section 3.3.1.2), colorants, ultraviolet stabilizer, and fire retardant. 

Epoxy resins are thermosetting matrix resins, characterized by the epoxide group [48,193], as shown in Figure 2.9. 

The use of advanced composites has increased significantly in the last decade. The properties of high-specific strength and stiffness make composites ideal for many aerospace, automotive, and infrastructure applications. Fiber-reinforced composites, which commonly use thermosetting resins such as epoxies as the matrix material, have some inherent deficiencies. These include the need for multistep processing, limited shelf-life, low toughness, sensitivity to moisture, and the inability to reprocess or reform the material [1]. 

The function of the resin matrix material in filament-wound structures is to help distribute the load, maintain proper fiber position, control composite mechanical and chemical properties, and provide interlaminar shear strength. Either a thermosetting or a thermoplastic resin material may be selected. Thermosetting resins may be selected for application in a wetwinding process or as part of a prepreg resin system. 

Two matrix flow submodels have been proposed the sequential compaction model [15] and the squeezed sponge model [11], Both flow models are based on Darcy s Law, which describes flow through porous media. Each composite layer is idealized as a fiber sheet surrounded by thermoset resin (Fig. 13.9). By treating the fiber sheet as a porous medium, the matrix velocity iir relative to the fiber sheet is given as (Eq. 13.5) ... 

Matrix materials for commercial composites are mainly liquid thermosetting resins such as polyesters, vinyl esters, epoxy resins, and bismaleimide resins. Thermoplastic composites are made from polyamides, polyether ether ketone (PEEK), polyphenylene sulfide (PPS), polysulfone, polyetherim-ide (PEI), and polyamide-imide (PAI). 

Composite In polymer technology a combination of a polymeric matrix and a reinforcing fiber with properties that the component materials do not have. The most common matrix resins are unsaturated thermosetting polyesters and epoxies, and reinforcing fibers are glass, carbon, and aramid fibers. The reinforcing fibers may be continuous or discontinuous. Some matrix resins are thermoplastics. 

Films of the polyisoimides were cast from DMAC at 55 °C under reduced pressure (0.1 mm). A study of the isomerization reaction was conducted by FTIR and showed that the isomerization began at approximately 100 °C and was complete after 3 h at 250 °C. In all cases the thermally treated films were insoluble in all solvents tested. Composite films were produced with XVII and three commercial matrix systems a polyarylsulfone (Radel), a polysulfone (Udel), and an acetylene terminated isoimide thermosetting resin (IP-600). Films of the matrix and XVII were cast from DMAC. Slightly cloudy films, indicating some phase separation, resulted with both the Radel and Udel systems. Composite films cast with IP-600, however, were completely clear and showed no signs of phase separation. The structural similarity of the IP-600 resin and XVII may account for the greater homogeneity of the system. Property assessment of these films before and after thermal treatment is currently underway. 

Core-shell emulsion polymers with a core or rubbery stage based on homopolymers or copolymers of butadiene are used as impact modifiers in matrix polymers, such as ABS, for styrene acrylonitrile copolymer methyl methacrylate (MMA) polymers, poly(vinyl chloride) (PVC), and in various engineering resins such as polycarbonate) (PC) poly(ester)s, or poly(styrene)s, further in thermosetting resins such as epoxies. 

---