Issuance policy

Another area these Debt Agencies have had to focus on more has been their communication policy. Another of the obvious consequences of the above mentioned loss of the domestic edge was the necessary increase in the transparency and predictability of these Debt Agencies, especially in terms of issuance policy. In fact, most Euro Debt Agencies now publish periodical supply calendars providing as much details as possible regard-... 

Relevance. A key criterion in the selection of biological indicators is relevance to human and ecological health and to the development of policy. Fish are directly relevant, for example, given that consumption of fish is the primary pathway for exposure to MeHg. The concentration of MeHg in fish is also a key variable in the issuance of fish-consumption advisories. 

ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals. 

Additional language in the preamble (TJ 15) to the GLP revisions of 1987 (4) as well as enforcement policies of individual the FDA investigators have broadly interpreted the requirement to include the current status of each study on the master schedule. According to this view, the master schedule should include such study events as test article-mixture preparation, test system dosing, and in-life observation. Because such detailed information is usually available in other study documentation (e.g., protocol, study schedules), most laboratories limit a description of current status to broad categories such as in-life phase, study terminated, report preparation, and report issuance. ... 

Issuance of the policy position of the Chemical Manufacturers Association is only an early step in the role CMA expects to play in the national debate over cost-benefit analysis in regulatory affairs. A number of CMA committees are actively engaged in examining the many issues involved, and worthwhile contributions to the debate from the chemical industry are likely. 

Manual of standard operating procedures and policies. Regulatory- License applications complete review and issuance of action letters. SOPP 8405. Center for Biologies Evaluation and Research, Eood and Drug Administration Rockville MD, 2003. 

Regulations specific to the control BPCs are a relatively new concept for many years FDA s policy was to apply a limited enforcement of the subpart 211 regulations for finished pharmaceuticals (6). In recent tears, FDA has endeavored to harmonize its approach to BPC regulation with the rest of the world, and has issued a guidance document that draws heavily on subpart 211 (7). This effort followed the issuance of a pharmaceutical inspection convention document that addressed the same subject in a different format (8). 

BSEE (Bureau of Safety and Environmental Enforcement), 2012b. Interim Policy Document. Issuance of Incident of Non Compliance (INC) to Contractors. 

Each State must provide notice of its intent to adopt either policies or procedures identical to those set out in this instruction, or alternative policies and procedures that are at least as effective. State policies and procedures must be adopted within six months of issuance of this instruction. If the State adopts policies and procedures that differ from the Federal program, the State must submit its different policies and procedures as a plan change supplanent with identification of the differences, within 60 days of adoption, and either post its different policies on its State plan website and provide the link to OSHA or provide OSHA with information on how the public may obtain a copy. If the State adopts identical policies and procedures, it must provide the date of adoption to OSHA and information on any State-specific procedures. OSHA will provide summary information on the State responses to this instruction on its website. 

The chief executive officer is responsible for the issuance of the safety and health policy and will demonstrate and accept safety accountability by ... 

It was not until January 1979 that layered vessels were included in die ASME Code, almost 50 years after they were first introduced. Also in 1979 the ASME Policy Board, Codes and Standards, approved the establishment of a special working group for high pressure vessels under Section VIII. This effort would ultimately culminate in the issuance of Division 3 of Section VIII in 1998. 

The issuance of a Limited Work Authorization (LWA) is under 10 CFR 50.10(e). In some cases, the NRC may authorize the licensee to do some construction at the site prior to the issuance of a construction permit. This authorization is known as an LWA and is done at the risk of the licensee. The LWA may be granted only after the licensing board has made all of the National Environmental Policy Act (NEPA) findings required by the Commission s regulations for authorizing construction and has determined that there is reasonable assurance that, from a public health and safety standpoint, the proposed site is a suitable location for a nuclear power reactor of the proposed type and capacity. 

In the late 1980s, DOE initiated tasks to provide new DOE orders that addressed nuclear safety documents and nuclear criticality safety. These documents were necessary to establish DOE nuclear safety policy and requirements in anticipation of the change to a regulated process. In 1991-1992, the DOE issued four DOE orders that defined the requirements for preparing Unreviewed Safety Questions (USQs) (DOE Order 5480.21), TSRs (DOE Order 5480.22), Safety Analysis Reports (DOE Order 5480.23), and Nuclear Criticality Safety (DOE Order 5480.24). They were used for the specification of nuclear safety requirements and used in conjunction with 10 CFR, Part 830 (10 CFR 830), Subpart A—Quality Assurance (QA) Requirements—for enforcement action under the PAAA regulatory process. These orders were deactivated on the issuance of 10 CFR 830, Subpart B—Safety Basis Requirements—and replaced by DOE guides. 

Force and Effect of Revised Policy. The revised policy provided in this Directive is in full force and effect from the date of its issuance. It is an official Agency policy to be implemented OSHA-wide. 

The North American Standard Level I and/or Level V are the only inspections that may result in issuance of a CVSA decal. To qualify for a CVSA decal, a vehicle must not have any Critical Vehicle Inspection Item violations contained in CVSA Operational Policy. 

In February, 1990 WSRC conducted a survey on the effectiveness of the Employee Concerns Program. An Action Plan to address program deficiencies was issued March 30, 1990 (Reference 19). . The plan addresses three objectives effective advertising, policy and procedure review, and development of performance indicators. Implementation of the plan is nearly complete. Closing tasks include issuance of a revi,sion to MRP 1.06 and the evaluation of performance Indicators, including an employee survey. 

---