Iso-butyl

Methyl formate. Ethyl formate Methyl acetate Iso-propyl formate Ethyl acetate Methyl propionate "-Propyl formate Iso-propyl acetate Methyl iso-butyrate Iso-butyl formate. Ethyl propionate M-Propyl acetate. Methyl butyrate. ... 

M-Butyl formate. Ethyl iso-butyrate IsO -butyl acetate Ethyl butyrate -Propyl propionate Iso-amyl formate, -But> l acetate Iso-propyl butyrate Iso-butyl propionate n-Propyl -butyrate -Butyl propionate Iso-butyl isobutyrate Ethyl lactate Iso-butyl butyrate Cycloheicyl formate -Butyl -butyrate Iso-propyl lactate. Cyclohexyl acetate Diethyl oxalate Di-iao-propyl oxalate... 

The student will doubtless be aware of the fact that methyl, ethyl, n-propyl and iso propyl alcohols are completely miscible with water. The solubilities of the higher aloohols decrease progressively as the carbon content increases. The solubilities of all types of alcohols with five carbon atoms or more are quite small. For the isomeric butyl alcohols the solubilities (g. per 100 g. of water at 20°) are n-butyl, 8 iso-butyl, 23 scc.-butyl, 13 ierl.-butyl, completely miscible. 

Fit a 500 ml. round-bottomed flask with a dropping funnel and a double surface condenser alternatively, the flask may be provided with a two-way addition tube (Fig. II, 13, 9) and the dropping funnel and condenser inserted into the latter. Place 37 g. (46 ml.) of iso-butyl alcohol (b.p. 106-108°) and 40 g. (41 ml.) of pure pyridine in the flask and 119 g. (73 ml.) of redistilled thionyl chloride in the dropping funnel. Insert a cotton wool or calcium chloride guard tube into the mouth of the funnel. Introduce the thionyl chloride during 3-4 hours a white solid... 

Successful results have been obtained (Renfrew and Chaney, 1946) with ethyl formate methyl, ethyl, n-propyl, iso-propyl, n-butyl, iso-butyl, sec.-butyl and iso-amyl acetat ethyleneglycol diacetate ethyl monochloro- and trichloro-acetates methyl, n-propyl, n-octyl and n-dodecyl propionates ethyl butyrate n-butyl and n-amyl valerates ethyl laurate ethyl lactate ethyl acetoacetate diethyl carbonate dimethyl and diethyl oxalates diethyl malonate diethyl adipate di-n-butyl tartrate ethyl phenylacetate methyl and ethyl benzoates methyl and ethyl salicylates diethyl and di-n-butyl phthalates. The method fails for vinyl acetate, ieri.-butyl acetate, n-octadecyl propionate, ethyl and >i-butyl stearate, phenyl, benzyl- and guaicol-acetate, methyl and ethyl cinnamate, diethyl sulphate and ethyl p-aminobenzoate. 

Vinoflax Vinyl chloride, vinyl iso butyl ether... 

Peroxides. These are formed by aerial oxidation or by autoxidation of a wide range of organic compounds, including diethyl ether, allyl ethyl ether, allyl phenyl ether, dibenzyl ether, benzyl butyl ether, n-butyl ether, iso-butyl ether, r-butyl ether, dioxane, tetrahydrofuran, olefins, and aromatic and saturated aliphatic hydrocarbons. They accumulate during distillation and can detonate violently on evaporation or distillation when their concentration becomes high. If peroxides are likely to be present materials should be tested for peroxides before distillation (for tests see entry under "Ethers", in Chapter 2). Also, distillation should be discontinued when at least one quarter of the residue is left in the distilling flask. 

High vacuum sublimation of the 3-monobenzoate of (32) or tosylchloride dehydration gives 3/ -benzoyloxy-7-methylenecholest-5-ene (33). The configuration of (32) is probably as shown since 7a-hydroxy steroids dehydrate readily to yield homoannular dienes. In an analogous reaction ethyl and iso-butyl Grignard reagents give alkylidene compounds as the only isolated products. 

Park et al. [20] reported on the synthesis of poly-(chloroprene-co-isobutyl methacrylate) and its compati-bilizing effect in immiscible polychloroprene-poly(iso-butyl methacrylate) blends. A copolymer of chloroprene rubber (CR) and isobutyl methacrylate (iBMA) poly[CP-Co-(BMA)] and a graft copolymer of iBMA and poly-chloroprene [poly(CR-g-iBMA)] were prepared for comparison. Blends of CR and PiBMA are prepared by the solution casting technique using THF as the solvent. The morphology and glass-transition temperature behavior indicated that the blend is an immiscible one. It was found that both the copolymers can improve the miscibility, but the efficiency is higher in poly(CR-Co-iBMA) than in poly(CR-g-iBMA),... 

Chemical deposition, gas or vapour plating This is a chemical process whereby the aluminium is deposited when an aluminium compound is pyrolysed. Organo-metallic compounds such as aluminium diethylhydride or tri-(iso) butyl aluminium (TIBA) are introduced into the work chamber after purging with an inert gas such as argon or nitrogen. The hydride... 

Properties Methyl iso-butyl ketone (MIBK) Tributyl phosphate (TBP) 2-octanol... 

Methyl iso-butyl ketone, 279-281 Microcalorimetry, 237 Molar conductivity, 155, 160 Molar volume, 156, 160... 

In order to concentrate the lead extract, remove the lead from the organic solvent by shaking this with three successive 10 mL portions of the dilute hydrochloric acid solution, collecting the aqueous extracts in a 250 mL beaker. To the combined extracts add 5 mL of 20 per cent ascorbic acid solution and adjust to pH 4 by the addition of concentrated ammonia solution. Place the beaker in a fume cupboard, add 3 mL of the 50 per cent potassium cyanide solution and immediately adjust the pH to 9-10 with concentrated ammonia solution. Transfer the solution to a 250 mL separatory funnel with the aid of a little de-ionised water, add 5 mL of the 2 per cent NaDDC reagent, allow to stand for one minute and then add 10 mL of methyl iso butyl ketone. Shake for one minute and then separate and collect the organic phase, filtering it through a fluted filter paper. This solution now contains the lead and is ready for the absorption measurement. 

---