Interface carbon-water

Williams and coworkers preliminarily reported that CO oxidation on Pt/Al203 is faster in the presence of water solvent than in the presence of ethanol [141]. We then studied CO oxidation on platinum surface in the presence of different solvents, and identified obvious solvent effects, namely, CO oxidation takes place the most easily with water solvent, the least easily with carbon tetrachloride solvent, and follows the overall trend of water > ethanol > methanol > cyclohexane > benzene carbon tetrachloride [67]. We subsequently took advantage of the solvent effect to design a diagnosing tool to pin down low-coverage CO at the liquid-solid interface, by flushing the liquid-solid interface with water and carbon tetrachloride individually [67]. 

Uchida, T. Ebinuma, T. Kawabata, J. Narita, H. (1999b). Microscopic observations of formation processes of clathrate-hydrate films at an interface between water and carbon dioxide. J. Crystal Growth, 204 (3), 348-356. 

The electrodes used in conventional polarography and voltammetry are electronic conductors such as metals, carbons or semiconductors. In an electrode reaction, an electron transfer occurs at the electrode/solution interface. Recently, however, it has become possible to measure both ion transfer and electron transfer at the interface between two immiscible electrolyte solutions (ITIES) by means of polarography and voltammetry [16]. Typical examples of the immiscible liquid-liquid interface are water/nitrobenzene (NB) and water/l,2-dichloroethane (DCE). 

Lipases are the most common enzymes used in non conventional media like organic solvents and supercritical carbon dioxide. Lipases usually hydrolyse fats into fatty acids and glycerol. The special property of lipases is their ability to act at the interface between water and oil. In these experiments lipase (EC 3.1.1.34) from Rhizopus arrhizus (Boehringer Mannheim) was used to investigate the effects of lipase under hydrostatic pressure. The analysed reaction was the hydrolysis of p-Nitrophenyllaureate at different concentrations at 35 °C. The dependance of the kinetic constants between 1 bar and 3000 bar is presented in table 2. Like the thermophilic GDH at 1000 bar lipase is activated under pressure as well. The initial reaction rate increases by a factor of 1.5 at 1000 bar compared to the initial reaction rate at ambient... 

We conclude that the proximal radial distribution function (Fig. 1.11) provides an effective deblurring of this interfacial profile (Fig. 1.9), and the deblurred structure is similar to that structure known from small molecule hydration results. The subtle differences of the ( ) for carbon-(water)hydrogen exhibited in Fig. 1.11 suggest how the thermodynamic properties of this interface, fully addressed, can differ from those obtained by simple analogy from a small molecular solute like methane such distinctions should be kept in mind together to form a correct physical understanding of these systems. 

The formation of three different condensed phases in the water-hydrocarbon-surfactant system allows one to measure the surface tension at the three interfaces, and to study the a(T) dependence at them (VI-19). Due to the dehydration of surfactant molecules, the interfacial tension at the aqueous solution - microemulsion interface, ow.me, increases with temperature, while the interfacial tension at the microemulsion - oil interface, a0.me, drops until a complete vanishing of this interface occurs. For the hydro carbon-water... 

Tsunoda, R., Ozawa, T. and Ando, J.-I. (1998). Ozone treatment of coal and coffee grounds-based active carbons water adsorption and surface fractal micropores. J. Colloid Interface Sci.,2tt5, 265—270. 

The other way of removing plasticizers from water is their adsorption at liquid-solid interface (i.e., soil or sediments) [11]. This process depends on hydrophobicity of the substance, i.e. is proportional to organic carbon-water partition coefficient Kqq - plasticizers with Kqq value greater than 1000 dm /kg are regarded as having relatively significant affinity for sediments and son. It means that it is of greater importance in the case of 2-ethylhexyl (hydrophobic alkyl chain) than in the case of dimethyl phthalate (see Table 3). 

Equation V-64 is that of a parabola, and electrocapillary curves are indeed approximately parabolic in shape. Because E ax tmd 7 max very nearly the same for certain electrolytes, such as sodium sulfate and sodium carbonate, it is generally assumed that specific adsorption effects are absent, and Emax is taken as a constant (-0.480 V) characteristic of the mercury-water interface. For most other electrolytes there is a shift in the maximum voltage, and is then taken to be Emax 0.480. Some values for the quantities are given in Table V-5 [113]. Much information of this type is due to Gouy [125], although additional results are to be found in most of the other references cited in this section. 

Qualitative examples abound. Perfect crystals of sodium carbonate, sulfate, or phosphate may be kept for years without efflorescing, although if scratched, they begin to do so immediately. Too strongly heated or burned lime or plaster of Paris takes up the first traces of water only with difficulty. Reactions of this type tend to be autocat-alytic. The initial rate is slow, due to the absence of the necessary linear interface, but the rate accelerates as more and more product is formed. See Refs. 147-153 for other examples. Ruckenstein [154] has discussed a kinetic model based on nucleation theory. There is certainly evidence that patches of product may be present, as in the oxidation of Mo(lOO) surfaces [155], and that surface defects are important [156]. There may be catalysis thus reaction VII-27 is catalyzed by water vapor [157]. A topotactic reaction is one where the product or products retain the external crystalline shape of the reactant crystal [158]. More often, however, there is a complicated morphology with pitting, cracking, and pore formation, as with calcium carbonate [159]. 

An interesting question that arises is what happens when a thick adsorbed film (such as reported at for various liquids on glass [144] and for water on pyrolytic carbon [135]) is layered over with bulk liquid. That is, if the solid is immersed in the liquid adsorbate, is the same distinct and relatively thick interfacial film still present, forming some kind of discontinuity or interface with bulk liquid, or is there now a smooth gradation in properties from the surface to the bulk region This type of question seems not to have been studied, although the answer should be of importance in fluid flow problems and in formulating better models for adsorption phenomena from solution (see Section XI-1). 

Adsorption — An important physico-chemical phenomenon used in treatment of hazardous wastes or in predicting the behavior of hazardous materials in natural systems is adsorption. Adsorption is the concentration or accumulation of substances at a surface or interface between media. Hazardous materials are often removed from water or air by adsorption onto activated carbon. Adsorption of organic hazardous materials onto soils or sediments is an important factor affecting their mobility in the environment. Adsorption may be predicted by use of a number of equations most commonly relating the concentration of a chemical at the surface or interface to the concentration in air or in solution, at equilibrium. These equations may be solved graphically using laboratory data to plot "isotherms." The most common application of adsorption is for the removal of organic compounds from water by activated carbon. 

---