Inspections removed

In the large packing establishments meat is inspected by the Bureau of Animal Industry Inspectors and meat infected with pathogenic microorganisms is eliminated. Ante-mortem inspection removes many diseased animals but rigid inspection of the carcasses immediately after slaughter detects the remainder. Nevertheless 25 to 40% of the meat consumed in the U. S. is said to escape inspection due to the fact that it is marketed through channels in which there is no inspection. 

Just like visual inspection, automated inspection systems do not require physical contact with the printed circuit assembly to generate the desired images. Unlike visual inspection, however, automated inspection removes human subjectivity from defect detection, thereby increasing repeatabihty rates typically by an order of magnitude. Many of the automated inspection systems also provide accurate, repeatable, quantitative measurements that directly correspond to process parameters, thus providing the means for process control and improvement. ... 

Cylinder sidewalls and bottoms must be in a condition that allows adequate visual inspection. If paint or other material has accumulated on the cylinder thick enough to prohibit full view of possible sidewall and bottom defects, such accumulation must be removed so that the surface can be adequately inspected. Removal of rust, scale, caked paint, or other foreign substances from the exterior surface may be accomplished by shot blasting, sand blasting, chemical stripping, sanding, or whatever approved method is available. 

Pipelines are cleaned and inspected using pigs . Pigs usually have a steel body fitted with rubber cups and brushes or scrapers to remove wax and rust deposits on the pipe wall, as the pig is pumped along the pipe. Sometimes spherical pigs are used for product separation or controlling liquid hold up. In field lines handling untreated crude may have to be insulated to prevent wax formation. 

For the repetitive inspections the required hydrotest can only be performed for a limited number of the small cylinders, and even then the drums have to be removed from the line and the cylinders will be supported in defined distances for the weight of the water and the pressurisation. For the new and long cylinders even this is impossible, because they loose due to the additional weight of the water and the over-pressurisation their roundness and balances. Therefore the law in the most countries within and outside of the EU accept as a replacement of the hydrotest an additional application of different NDT methods, which were often done by an ultrasonic measurement of the wall thickness of the cylindrical part and a MT of the flat covers. 

The advantages of the above air bath are (1) simplicity and cheapness of construction (2)ease of temperature control (3) rapidity of cooling of the contents of the flask effected either by removing the asbestos covers or by completely removing the air bath and (4) the contents of the flask may be inspected by removing the asbestos covers. 

The particle sizes of fillers are usually collected and ordered to yield size distributions which are frequendy plotted as cumulative weight percent finer than vs diameter, often given as esd, on a log probabiUty graph. In this manner, most unmodified fillers yield a straight-line relationship or log normal distribution. Inspection of the data presented in this manner can yield valuable information about the filler. The coarseness of a filler is often quantified as the esd at the 99.9% finer-than value. Deviations from linearity at the high and low ends of the plot suggest that either fractionation has occurred to remove coarse or fine particles or the data are suspect in these ranges. 

The gas leaving the heat recovery equipment contains soot and ash some ash is deposited in the bottom of the reactor for removal during periodic inspection shutdowns. The gas passes to a quench vessel containing multiple water-sprays which scmb most of the soot from the gas. Additional heat recovery can be accompHshed downstream of the quench vessel by heat exchange of the gas with cold feed water. Product gas contains less than 5 ppm soot. 

RCRA incinerator regulations include adrninistrative as weU as performance standards. Administrative standards include procedures for waste analysis, inspection of equipment, monitoring, and facihty security. Steps needed to meet adrninistrative standards are outlined ia the permit apphcation performance standards are demonstrated during a trial bum. Trial bum operating conditions are included in the permit to assure ongoing compliance with the performance standards. Performance standards include destmction and removal efficiency (DRE), particulate emissions limits, products of incomplete combustion emission limits, metal emission limits, and HCl and Cl emission limits (see Exhaust CONTROL, INDUSTRIAL). 

Air cleaning systems are often used to remove dust or vapors from plant or process exhaust streams. Dust collecting systems such as filters or electrostatic precipitators that handle heavy loads of dust are usually designed to be self-cleaning, but it is stiU. necessary to enter the air cleaner periodically for inspection or repair. Dust deposits inside the equipment are likely to be stirred up and inhaled by unprotected workers. Baghouses are particularly likely to cause exposure because large amounts of dust may be retained in the cloth and released when the bags are handled. 

The chrome-tanned leather is removed from the dmm and wmng to remove the absorbed tanning solution. The leather is then inspected for quaUty of the grain and other characteristics of importance for the leather being made. In large tanneries where very uniform hides are worked, the leather may be trimmed and spHt to the desired thickness. Hides spHt before tanning need no splitting at this point. 

A schematic diagram of the polymer precipitation process is shown in Figure 8. The hot polymer solution is cast onto a water-cooled chill roU, which cools the solution, causing the polymer to precipitate. The precipitated film is passed through an extraction tank containing methanol, ethanol or 2-propanol to remove the solvent. Finally, the membrane is dried, sent to a laser inspection station, trimmed, and roUed up. The process shown in Figure 8... 

Filtered-Particle Inspection. Solids containing extensive inteiconnected porosity, eg, sintered metallic or fired ceramic bodies formed of particles that ate typically of 0.15-mm (100-mesh) screen size, are not inspectable by normal Hquid penetrant methods. The preferred test medium consists of a suspension of dyed soHd particles, which may be contained in a Hquid vehicle dyed with a different color. Test indications can form wherever suspensions can enter cracks and other discontinuities open to the surface and be absorbed in porous material along interior crack walls. The soHd particles that form test indications ate removed by filtration along the line of the crack at the surface where they form color or fluorescent indications visible under near-ultraviolet light (1,3). 

Sepa.ra.tedRecyclables. Even when initial separation of recyclables takes place at the household level, the separated materials stiU requite some preparation before being sent to market. By visually inspecting materials, facihty processors are able to remove any remaining contaminants. This ensures that recyclables will be of sufficient quahty to meet buyer specifications. In addition, materials are often shredded, cmshed, or baled to facihtate cost-effective shipping. 

To add surface area, the supports are uniformly coated with a slurry of gamma-alumina and recalcined under moderate conditions. The wash coat acts to accept the active metals, typically low levels of platinum and palladium, in a conventional impregnation process. In the United States in passenger car apphcations the spherical catalyst is used almost exclusively, and methods have been developed to replace the catalyst without removing the converter shell when vehicle inspection reveals that emission standards are not met. 

Visual inspection and removal via conveyor belt picking stations... 

---