HIGH CONVERSION

Maximum selectivity requires a minimum ratio rjr in Eq. (2.17). A high conversion in the reactor tends to decrease Cfeed- Thus... 

If the reaction involves more than one feed, it is not necessary to operate with the same low conversion on all the feeds. Using an excess of one of the feeds enables operation with a relatively high conversion of other feed material, and still inhibits series reactions. Consider again the series reaction system from Example 2.3 ... 

This is an endothermic reaction accompanied by an increase in the number of moles. High conversion is favored by high temperature and low pressure. The reduction in pressure is achieved in practice by the use of superheated steam as a diluent and by operating the reactor below atmospheric pressure. The steam in this case fulfills a dual purpose by also providing heat for the reaction. 

An initial guess for the reactor conversion is very difficult to make. A high conversion increases the concentration of monoethanolamine and increases the rates of the secondary reactions. As we shall see later, a low conversion has the effect of decreasing the reactor capital cost but increasing the capital cost of many other items of equipment in the flowsheet. Thus an initial value of 50 percent conversion is probably as good as a guess as can be made at this stage. 

Figure 8.4 shows the cost tradeoffs for the present case. At high conversions, the raw materials costs due to byproduct formation are dominant. This is so because the reaction to the undesired... 

If air is used, then a single pass with respect to each feedstock is used and no recycle to the reactor (Fig. 10.4a).-Thus the process operates at near stoichiometric feed rates to achieve high conversions. Typically, between 0.7 and 1.0 kg of vent gases are emitted per kilogram of dichloroethane produced. ... 

The conversion to lighter products is limited by the asphaltenes content (C insolubles). At high conversions, the residual asphaltenes —no longer being soluble in their environment— tend to precipitate, resulting in the production of unstable residues that are unmarketable. 

Mariette, L., A. Billon and T. Descourieres (1988), Hyvahl process for high conversion of resids . Japanese Petroleum Institute Conference, Tokyo. 

Throughout this section we have used mostly p and u to describe the distribution of molecular weights. It should be remembered that these quantities are defined in terms of various concentrations and therefore change as the reactions proceed. Accordingly, the results presented here are most simply applied at the start of the polymerization reaction when the initial concentrations of monomer and initiator can be used to evaluate p or u. The termination constants are known to decrease with the extent of conversion of monomer to polymer, and this effect also complicates the picture at high conversions. Note, also, that chain transfer has been excluded from consideration in this section, as elsewhere in the chapter. We shall consider chain transfer reactions in the next section. 

The magnitude of the individual terms in the summation depends on both th( specific chain transfer constants and the concentrations of the reactants undei consideration. The former are characteristics of the system and hence quantitie over which we have little control the latter can often be adjusted to study particular effect. For example, chain transfer constants are generally obtainec under conditions of low conversion to polymer where the concentration o polymer is low enough to ignore the transfer to polymer. We shall return belov to the case of high conversions where this is not true. 

As noted above, chain transfer to polymer does not interfere with the determination of other transfer constants, since the latter are evaluated at low conversions. In polymer synthesis, however, high conversions are desirable and extensive chain transfer can have a dramatic effect on the properties of the product. This comes about since chain transfer to polymer introduces branching into the product ... 

Bulk and solution polymerizations are more or less self-explanatory, since they operate under the conditions we have assumed throughout most of this chapter. A bulk polymerization may be conducted with as few as two components monomer and initiator. Production polymerization reactions are carried out to high conversions which produces several consequences we have mentioned previously ... 

The scattered radiation V3 is to high wavenumber of Vj (i.e. on the anti-Stokes side) and is coherent, unlike spontaneous Raman scattering hence the name CARS. As a consequence of the coherence of the scattering and the very high conversion efficiency to V3, the CARS radiation forms a collimated, laser-like beam. 

Even ia 1960 a catalytic route was considered the answer to the pollution problem and the by-product sulfate, but nearly ten years elapsed before a process was developed that could be used commercially. Some of the eadier attempts iacluded hydrolysis of acrylonitrile on a sulfonic acid ion-exchange resia (69). Manganese dioxide showed some catalytic activity (70), and copper ions present ia two different valence states were described as catalyticaHy active (71), but copper metal by itself was not active. A variety of catalysts, such as Umshibara or I Jllmann copper and nickel, were used for the hydrolysis of aromatic nitriles, but aUphatic nitriles did not react usiag these catalysts (72). Beginning ia 1971 a series of patents were issued to The Dow Chemical Company (73) describiag the use of copper metal catalysis. Full-scale production was achieved the same year. A solution of acrylonitrile ia water was passed over a fixed bed of copper catalyst at 85°C, which produced a solution of acrylamide ia water with very high conversions and selectivities to acrylamide. 

If a linear mbber is used as a feedstock for the mass process (85), the mbber becomes insoluble in the mixture of monomers and SAN polymer which is formed in the reactors, and discrete mbber particles are formed. This is referred to as phase inversion since the continuous phase shifts from mbber to SAN. Grafting of some of the SAN onto the mbber particles occurs as in the emulsion process. Typically, the mass-produced mbber particles are larger (0.5 to 5 llm) than those of emulsion-based ABS (0.1 to 1 llm) and contain much larger internal occlusions of SAN polymer. The reaction recipe can include polymerization initiators, chain-transfer agents, and other additives. Diluents are sometimes used to reduce the viscosity of the monomer and polymer mixture to faciUtate processing at high conversion. The product from the reactor system is devolatilized to remove the unreacted monomers and is then pelletized. Equipment used for devolatilization includes single- and twin-screw extmders, and flash and thin film evaporators. Unreacted monomers are recovered for recycle to the reactors to improve the process yield. 

Chlorine Trifluoride. Chlorine trifluoride is produced commercially by the continuous gas-phase reaction of fluorine and chlorine ia a nickel reactor at ca 290°C. The ratio of fluorine to chlorine is maintained slightly in excess of 3 1 to promote conversion of the chlorine monofluoride to chlorine trifluoride. Sufficient time ia the reactor must be provided to maintain high conversions to chlorine trifluoride. Temperature control is also critical because the equiHbrium shift of chlorine trifluoride to chlorine monofluoride and fluorine is significant at elevated temperatures. 

For example, ia the iadustriaHy important alkylation of benzene with ethylene to ethylbenzene, polyethylbenzenes are also produced. The overall formation of polysubstituted products is minimized by recycling the higher ethylation products for the ethylation of fresh benzene (14). By adding the calculated equiUbrium amount of polyethylbenzene to the benzene feed, a high conversion of ethylene to monoethylbenzene can be achieved (15) (see also... 

Eigure 2 shows that even materials which are rather resistant to oxidation ( 2/ 1 0.1) are consumed to a noticeable degree at high conversions. Also the use of plug-flow or batch reactors can offer a measurable improvement in efficiencies in comparison with back-mixed reactors. Intermediates that cooxidize about as readily as the feed hydrocarbon (eg, ketones with similar stmcture) can be produced in perhaps reasonable efficiencies but, except at very low conversions, are subject to considerable loss through oxidation. They may be suitable coproducts if they are also precursors to more oxidation-resistant desirable materials. Intermediates which oxidize relatively rapidly (/ 2 / i — 3-50 eg, alcohols and aldehydes) are difficult to produce in appreciable amounts, even in batch or plug-flow reactors. Indeed, for = 50, to isolate 90% or more of the intermediate made, the conversion must... 

Wheieas the BPO—DMA ledox system works well for curing of unsaturated polyester blends, it is not a very effective system for initiating vinyl monomer polymerizations, and therefore it generally is not used in such appHcations (34). However, combinations of amines (eg, DMA) and acyl sulfonyl peroxides (eg, ACSP) are very effective initiator systems at 0°C for high conversion suspension polymerizations of vinyl chloride (35). BPO has also been used in combination with ferrous ammonium sulfate to initiate emulsion polymerizations of vinyl monomers via a redox reaction (36). 

Initia.tors, The initiators most commonly used in emulsion polymerization are water soluble although partially soluble and oil-soluble initiators have also been used (57). Normally only one initiator type is used for a given polymerization. In some cases a finishing initiator is used (58). At high conversion the concentration of monomer in the aqueous phase is very low, leading to much radical—radical termination. An oil-soluble initiator makes its way more readily into the polymer particles, promoting conversion of monomer to polymer more effectively. 

Only with propanal are very high conversions (99%) and selectivity (> 98 0) to MMA and MAA possible at this time. Although nearly 95% selective, the highest reported conversions with propionic acid or methyl propionate are only 30—40%. This results in large recycle streams and added production costs. The propanal route suffers from the added expense of the additional step required to oxidize methacrolein to methacrylic acid. 

The chemical resistance and excellent light stabiUty of poly(methyl methacrylate) compared to two other transparent plastics is illustrated in Table 5 (25). Methacrylates readily depolymerize with high conversion, ie, 95%, at >300° C (1,26). Methyl methacrylate monomer can be obtained in high yield from mixed polymer materials, ie, scrap. 

Bulk Polymerization. This is the method of choice for the manufacture of poly(methyl methacrylate) sheets, rods, and tubes, and molding and extmsion compounds. In methyl methacrylate bulk polymerization, an auto acceleration is observed beginning at 20—50% conversion. At this point, there is also a corresponding increase in the molecular weight of the polymer formed. This acceleration, which continues up to high conversion, is known as the Trommsdorff effect, and is attributed to the increase in viscosity of the mixture to such an extent that the diffusion rate, and therefore the termination reaction of the growing radicals, is reduced. This reduced termination rate ultimately results in a polymerization rate that is limited only by the diffusion rate of the monomer. Detailed kinetic data on the bulk polymerization of methyl methacrylate can be found in Reference 42. 

Because very high conversions generally are not obtained or desired, the hydroperoxide is removed from the oxidation stream by extraction with aqueous alkah. 

Alternating current is converted to direct current (dc) for the smelting cells by siUcon rectifiers. High conversion efficiency (over 99%) and minimum capital costs are achieved when the rectified voltage is 600—900 V dc. Because aluminum smelting cells operate at 4.5—5.0 V, 130 or more cells are coimected in series, forming what the industry calls a potline, which may operate at 50—360 kA. 

Tubular Reactors. The tubular reactor is exceUent for obtaining data for fast thermal or catalytic reactions, especiaHy for gaseous feeds. With sufficient volume or catalyst, high conversions, as would take place in a large-scale unit, are obtained conversion represents the integral value of reaction over the length of the tube. Short tubes or pancake-shaped beds are used as differential reactors to obtain instantaneous reaction rates, which can be computed directly because composition changes can be treated as differential amounts. Initial reaction rates are obtained with a fresh feed. Reaction rates at... 

Fig. 15. Temperature vs heat generation or removal in estabHshing stationary states. The heavy line (—) shows the effect of reaction temperature on heat-generation rates for an exothermic first-order reaction. Curve A represents a high rate of heat removal resulting in the reactor operating at a low temperature with low conversion, ie, stationary state at a B represents a low rate of heat removal and consequently both a high temperature and high conversion at its stationary state, b and at intermediate heat removal rates, ie, C, multiple stationary states are attainable, c and The stationary state at c ...

---