Heterogeneous catalysis metals, reactions

Solutions of ruthenium carbonyl complexes in acetic acid solvent under 340 atm of 1 1 H2/CO are stable at temperatures up to about 265°C (166). Reactions at higher temperatures can lead to the precipitation of ruthenium metal and the formation of hydrocarbon products. Bradley has found that soluble ruthenium carbonyl complexes are unstable toward metallization at 271°C under 272 atm of 3 2 H2/CO [109 atm CO partial pressure (165)]. Solutions under these conditions form both methanol and alkanes, products of homogeneous and heterogeneous catalysis, respectively. Reactions followed with time exhibited an increasing rate of alkane formation corresponding to the decreasing concentration of soluble ruthenium and methanol formation rate. Nevertheless, solutions at temperatures as high as 290°C appear to be stable under 1300 atm of 3 2 H2/CO. 

Transition metals play an important role in heterogeneous catalysis where reactions occur on the surfaces of metal or oxide crystals. Typical of these metals are V or Mo which exist in oxides with tetrahedral, tetragonal pyramidal, or octahedral coordination and which can change their oxidation states with minimal changes in their coordination environment. As in the case of soil minerals (Section 13.4.1), bond valences can be used to determine the bonding strength of the anions on the surface, by noting how far the valence sums around the surface ions fall short of 2.00 vu. 

Kinetic analysis of concrete catalytic reactions. In the kinetics of heterogeneous catalysis, such reactions are usually model oxidation reactions (e.g. CO and H2 oxidation) over metals. 

It was previously stressed that apparent heterogeneous catalysis could be the result of the leaching of minute amount metal 7 10. By this work, we have demonstrated the existence of a new kind of "pseudo heterogeneous" catalysis a reaction in which the effective catalyst is dissolved to be active, but precipitates when the conversion is complete. These results constitute a new demonstration that recycling is not an appropriate proof of the heterogeneity of catalysis in liquid phase oxidation. 

The study of dissociative chemisorption of gas-phase molecules on metal surfaces is important to the understanding of a myriad of processes such as heterogeneous catalysis, electrode reactions, and corrosion, to name but a few (179-181). Recent advances in molecular beam, laser, and surface detection technologies have made it possible to study the reactions of monoenergetic molecular beams with clean, well-characterized metal surfaces. 

Incorporation of metallo-phthalocyanines and metallo-porphyrins into PIM networks helps to allow access to the catalytic metal centers. It was shown that such network-PIMs demonstrate effective heterogeneous catalysis in reactions such as the oxidation of hydroquinone. Desulfurization of salt water has been shown to be catalyzed by a cobalt phthalocyanine network-PIM. Suzuki carbon-carbon coupling reactions can be catalyzed effectively by a hexaazatrinaphthylene-based Pd-loaded PIM network. 

The microscopic understanding of tire chemical reactivity of surfaces is of fundamental interest in chemical physics and important for heterogeneous catalysis. Cluster science provides a new approach for tire study of tire microscopic mechanisms of surface chemical reactivity [48]. Surfaces of small clusters possess a very rich variation of chemisoriDtion sites and are ideal models for bulk surfaces. Chemical reactivity of many transition-metal clusters has been investigated [49]. Transition-metal clusters are produced using laser vaporization, and tire chemical reactivity studies are carried out typically in a flow tube reactor in which tire clusters interact witli a reactant gas at a given temperature and pressure for a fixed period of time. Reaction products are measured at various pressures or temperatures and reaction rates are derived. It has been found tliat tire reactivity of small transition-metal clusters witli simple molecules such as H2 and NH can vary dramatically witli cluster size and stmcture [48, 49, M and 52]. 

Of these, the most extensive use is to identify adsorbed molecules and molecular intermediates on metal single-crystal surfaces. On these well-defined surfaces, a wealth of information can be gained about adlayers, including the nature of the surface chemical bond, molecular structural determination and geometrical orientation, evidence for surface-site specificity, and lateral (adsorbate-adsorbate) interactions. Adsorption and reaction processes in model studies relevant to heterogeneous catalysis, materials science, electrochemistry, and microelectronics device failure and fabrication have been studied by this technique. 

Nonstoichiometric oxide phases are of great importance in semiconductor devices, in heterogeneous catalysis and in understanding photoelectric, thermoelectric, magnetic and diffusional properties of solids. They have been used in thermistors, photoelectric cells, rectifiers, transistors, phosphors, luminescent materials and computer components (ferrites, etc.). They are cmcially implicated in reactions at electrode surfaces, the performance of batteries, the tarnishing and corrosion of metals, and many other reactions of significance in catalysis. ... 

This type of co-catalytic influence is well loiown in heterogeneous catalysis, in which for some reactions an acidic support will activate a metal catalyst more efficiently than a neutral support. In this respect, the acidic ionic liquid can be considered as a liquid acidic support for the transition metal catalysts dissolved in it. 

Perhaps the most familiar example of heterogeneous catalysis is the series of reactions that occur in the catalytic converter of an automobile (Figure 11.12). Typically this device contains 1 to 3 g of platinum metal mixed with rhodium. The platinum catalyzes the oxidation of carbon monoxide and unburned hydrocarbons such as benzene, C6H6 ... 

One problem with heterogeneous catalysis is that the solid catalyst is easily poisoned. Foreign materials deposited on the catalytic surface during the reaction reduce or even destroy its effectiveness. A major reason for using unleaded gasoline is that lead metal poisons the Pt-Rh mixture in the catalytic converter. 

Wagner was first to propose the use of solid electrolytes to measure in situ the thermodynamic activity of oxygen on metal catalysts.17 This led to the technique of solid electrolyte potentiometry.18 Huggins, Mason and Giir were the first to use solid electrolyte cells to carry out electrocatalytic reactions such as NO decomposition.19,20 The use of solid electrolyte cells for chemical cogeneration , that is, for the simultaneous production of electrical power and industrial chemicals, was first demonstrated in 1980.21 The first non-Faradaic enhancement in heterogeneous catalysis was reported in 1981 for the case of ethylene epoxidation on Ag electrodes,2 3 but it was only... 

Wagner first proposed the use of such galvanic cells in heterogeneous catalysis, to measure in situ the thermodynamic activity of oxygen O(a) adsorbed on metal electrodes during catalytic reactions.21 This led to the technique of solid electrolyte potentiometry (SEP).22 26... 

Reactivity studies of organic ligands with mixed-metal clusters have been utilized in an attempt to shed light on the fundamental steps that occur in heterogeneous catalysis (Table VIII), although the correspondence between cluster chemistry and surface-adsorbate interactions is often poor. While some of these studies have been mentioned in Section ll.D., it is useful to revisit them in the context of the catalytic process for which they are models. Shapley and co-workers have examined the solution chemistry of tungsten-iridium clusters in an effort to understand hydrogenolysis of butane. The reaction of excess diphenylacetylene with... 

Gas-surface interactions and reactions on surfaces play a crucial role in many technologically important areas such as corrosion, adhesion, synthesis of new materials, electrochemistry and heterogeneous catalysis. This chapter aims to describe the interaction of gases with metal surfaces in terms of chemical bonding. Molecular orbital and band structure theory are the basic tools for this. We limit ourselves to metals. 

The underlying problem in testing the validity of the additivity principle in corrosion, mineral extraction, and electroless plating is that the electrode metal itself forms part of one of the half-reactions involved, e.g., zinc in equation (5) and copper in equations (8) and (12). A much better test system is provided by the interaction of two couples at an inert metal electrode that does not form a chemical part of either couple. A good example is the heterogeneous catalysis by platinum or a similar inert metal of the reaction... 

---