Feedstock mixed

The feedstock, mixed with recycle stock from the fractionator, is injected into the cracker is immediately absorbed into the pores of the particles by capillary force and is subjected to thermal cracking (Figure 8-7). In consequence, the surface of the noncatalytic particles is kept dry and good fluidity is maintained allowing a good yield of, and selectivity for, middle distillate products (Table 8-3). Hydrogen-containing gas from the fractionator is used for the fluidization in the cracker. 

The market value of natural gas Hquids is highly volatile and historically has been weakly related to the world price of cmde oil. During the 1980s, the market value of natural gas Hquids ranged from approximately 60% of the price of cmde to 73% (12). In this 10-year interval, several fluctuations occurred in the natural gas Hquid market. Because of the variabiHty of the natural gas Hquid market, the NGL recovery plants need to have flexibiHty. Natural gas Hquid products compete in the following markets ethane propane a Hquefted petroleum gas (LPG) a C-3/C-4 mix and / -butane all compete as petrochemical feedstocks. Propane and LPG are also used as industrial and domestic fuels, whereas 2-butane and natural gasoline, consisting of C-5 and heavier hydrocarbons, are used as refinery feedstocks. 

A considerable amount of carbon is formed in the reactor in an arc process, but this can be gready reduced by using an auxiUary gas as a heat carrier. Hydrogen is a most suitable vehicle because of its abiUty to dissociate into very mobile reactive atoms. This type of processing is referred to as a plasma process and it has been developed to industrial scale, eg, the Hoechst WLP process. A very important feature of a plasma process is its abiUty to produce acetylene from heavy feedstocks (even from cmde oil), without the excessive carbon formation of a straight arc process. The speed of mixing plasma and feedstock is critical (6). 

When the recycle soot in the feedstock is too viscous to be pumped at temperatures below 93°C, the water—carbon slurry is first contacted with naphtha carbon—naphtha agglomerates are removed from the water slurry and mixed with additional naphtha. The resultant carbon—naphtha mixture is combined with the hot gasification feedstock which may be as viscous as deasphalter pitch. The feedstock carbon—naphtha mixture is heated and flashed, and then fed to a naphtha stripper where naphtha is recovered for recycle to the carbon—water separation step. The carbon remains dispersed in the hot feedstock leaving the bottom of the naphtha stripper column and is recycled to the gasification reactor. 

Process Technology Evolution. Maleic anhydride was first commercially produced in the early 1930s by the vapor-phase oxidation of benzene [71-43-2]. The use of benzene as a feedstock for the production of maleic anhydride was dominant in the world market well into the 1980s. Several processes have been used for the production of maleic anhydride from benzene with the most common one from Scientific Design. Small amounts of maleic acid are produced as a by-product in production of phthaHc anhydride [85-44-9]. This can be converted to either maleic anhydride or fumaric acid. Benzene, although easily oxidized to maleic anhydride with high selectivity, is an inherently inefficient feedstock since two excess carbon atoms are present in the raw material. Various compounds have been evaluated as raw material substitutes for benzene in production of maleic anhydride. Fixed- and fluid-bed processes for production of maleic anhydride from the butenes present in mixed streams have been practiced commercially. None of these... 

Noncatalytic partial oxidation of residual fuel oil accounts for the remainder of world methanol production. Shell and Texaco ate the predominant hcensors for partial oxidation technology (16) the two differ principally in the mechanical details of mixing the feedstock and oxidant, in waste heat recovery, and in soHds management. 

In addition to these principal commercial uses of molybdenum catalysts, there is great research interest in molybdenum oxides, often supported on siHca, ie, MoO —Si02, as partial oxidation catalysts for such processes as methane-to-methanol or methane-to-formaldehyde (80). Both O2 and N2O have been used as oxidants, and photochemical activation of the MoO catalyst has been reported (81). The research is driven by the increased use of natural gas as a feedstock for Hquid fuels and chemicals (82). Various heteropolymolybdates (83), MoO.-containing ultrastable Y-zeoHtes (84), and certain mixed metal molybdates, eg, MnMoO Ee2(MoO)2, photoactivated CuMoO, and ZnMoO, have also been studied as partial oxidation catalysts for methane conversion to methanol or formaldehyde (80) and for the oxidation of C-4-hydrocarbons to maleic anhydride (85). Heteropolymolybdates have also been shown to effect ethylene (qv) conversion to acetaldehyde (qv) in a possible replacement for the Wacker process. 

The naphthalene is vaporized, mixed with air, and fed to the top of the reactor. This process also allows for mixtures of ortho- s.yXen.e [95-47-6] to be mixed with the naphthalene and air, which permits the use of dual feedstocks. Both feedstocks are oxidized to phthaUc anhydride. The typical range of reactor temperature is 340—380°C. The reactor temperatures are controlled by an external molten salt. 

Propjiene (qv) [115-07-1] is the predominant 0x0 process olefin feedstock. Ethylene (qv) [74-85-1J, as well as a wide variety of terminal, internal, and mixed olefin streams, are also hydroformylated commercially. Branched-chain olefins include octenes, nonenes, and dodecenes from fractionation of oligomers of C —C olefins as well as octenes from dimerization and codimerization of isobutylene and 1- and 2-butenes (see Butylenes). 

The stringency of the conditions employed in the unmodified cobalt 0x0 process leads to formation of heavy trimer esters and acetals (2). Although largely supplanted by low pressure ligand-modified rhodium-catalyzed processes, the unmodified cobalt 0x0 process is stiU employed in some instances for propylene to give a low, eg, - 3.3-3.5 1 isomer ratio product mix, and for low reactivity mixed and/or branched-olefin feedstocks, eg, propylene trimers from the polygas reaction, to produce isodecanol plasticizer alcohol. 

Bisphosphites such as (7) combine excellent reactivity, straight-chain selectivity, and high resistance to the typical phosphite degradation reactions (29). Further, the corresponding 0x0 catalysts are excellent olefin isomerization catalysts so that high normal-to-branched isomer ratios are obtained even from internal olefins, enabling, in certain instances, the use of inexpensive mixed isomer olefin feedstocks. 

The largest use of NMP is in extraction of aromatics from lube oils. In this appHcation, it has been replacing phenol and, to some extent, furfural. Other petrochemical uses involve separation and recovery of aromatics from mixed feedstocks recovery and purification of acetylenes, olefins, and diolefins removal of sulfur compounds from natural and refinery gases and dehydration of natural gas. 

---