Exposure employee, measurement

Exposure protection measures employees can take (i.e., modif5dng smoking habits, using hygiene, work practices, and personal protective equipment (PPE)). 

D) Name, social security number, and job classification of the employee monitored and of all other employees whose exposure the measurement is intended to represent and... 

B. Your employer is required to determine whether you are being exposed to asbestos. Your employer must treat exposure to thermal system insulation and sprayed-on and troweled-on surfacing material as asbestos exposure, unless results of laboratory analysis show that the material does not contain asbestos. You or your representative has the right to observe employee measurements and to record the results obtained. Your employer is required to inform you of your exposure, and, if you are exposed above the permissible exposure limit, he or she is required to Inform you of the actions that are being taken to reduce your exposure to within the permissible limit. 

Eight hour exposure evaluation Measurements taken for the purpose of determining employee exposure under this section are best taken so that the average... 

Emergencies. Emergencies, and the facts obtainable at that time, shall be reported within seventy-two (72) hours of the initial occurrence to the OSHA Area Office. Upon request of the OSHA Area Office the employer shall submit additional information in writing relevant to the nature and extent of employee exposures and measures taken to prevent future emergencies of a similar nature. 

Eight-hour exposure evaluation Measurements taken for the purpose of determining employee exposure under this section are best taken so that the average 8-hour exposure may be determined from a single 8-hour sample or two (2) 4-hour samples. Air samples should be taken in the employee s breathing zone (air that would most nearly represent that inhaled by the employee.)... 

There Is no one correct way to determine employee exposure. Obviously, measuring the exposure of every employee exposed to formaldehyde will provide the most information on any given day. Where few employees are exposed, this may be a practical solution. For most employers, however, use of the following strategy will give just as much information at less cost. 

The burden on the employer to provide adequate protection for their employees is minimized. They don t have to make measurements inside respirators. They just need to make general exposure assessment measurements. ... 

The U.S. Department of Labor (OSHA) has ruled that an employee s exposure to dimethyl acetamide in any 8-h work shift of a 40-h work week shall not exceed a time-weighted average of 10 ppm DMAC vapor in air by volume or 35 mg/m in air by weight (7). If there is significant potential for skin contact with DMAC, biological monitoring should be carried out to measure the level of DMAC metaboHtes in urine specimens collected at the end of the shift. One industrial limit is 40 ppm DMAC metaboHtes, expressed as AJ-methylacetamide [79-16-3] for individuals, and 20 ppm metaboHte average for workers on the job (8). 

Operations capable of generating airborne beryUium particulate, such as melting, machining, welding, grinding, etc, are effectively controUed by local exhaust ventilation or other control measures. To assure a safe environment and measure compliance with the OSHA standards, employee exposures should be periodicaUy measured by prescribed air sampling and analytical methods. 

Risk indices are usually single-number estimates, which may be used to compare one risk with another or used in an absolute sense compared to a specific target. For risks to employees the fatal accident rate (FAR) is a commonly apphed measure. The FAR is a singlenumber index, which is the expected number of fatalities from a specific event based on 10 exposure hours. For workers in a chemical plant, the FAR could be calculated as follows ... 

Before starting any work which is liable to expose employees to asbestos dust, an assessment of the work is required to help decide the measures necessary to control exposure. This should ... 

Conduct a risk assessment to any employee and other persons to identify measures needed to restrict exposure to ionizing radiation and to assess magnitude of risk including identifiable accidents. 

The Material Safety Data Sheet (MSDS) is a detailed information bulletin prepared by the manufacturer or importer of a chemical tliat describes tlie physical and healtli hazards, routes of exposure, precautions for safe handling and use, emergency and first-aid procedures, and control measures. Infonnation on an MSDS aids in tlie selection of safe products and helps prepare employers and employees to respond effectively to daily exposure situations as well as to emergency situations. It is also a source of information for identifying chemical hazards. 

Radioactive plutonium isotopes emit alpha particles. The amount of radioactive plutonium in a sample can be measured by alpha spectroscopy, a technique for counting the alpha radiation. The technique is used at the Los Alamos National Laboratory (LANL) in New Mexico in order to monitor employees for exposure. 

It is essential to ensure that employees are not exposed to toxic materials at levels above or for durations beyond those permitted by TLV s or the equivalent. It is thus necessary to ensure by periodic measurement that atmospheric levels of toxic materials throughout the work shift do not exceed the permitted levels. Measurement of atmospheric toxic exposures has been discussed in Chapter 11. The frequency of this air sampling depends on the potential for exposure and injury. Where the hazard is relatively low and actions have been taken to control it, occasional checks by a knowledgeable but not necessarily professional person are desirable to ensure that the control is effective. Where there is a potential for serious hazard, for example, where high-hazard materials are handled in quantity,... 

After all data has been compiled to show TWA values this information is then shared with employees using a computerized employee exposure form. This concludes the task of dust measurement by means of the standardized vertical elutriator method. 

---