Examination Methods

Correlation between the body forces and the stress state in the head was investigated both by the strain gauge method and the optical coat work stress examination method, and the magnetic measurements were performed at the same time. 

During the optical coat work stress examination method the upper plate of the head of some of the bolts was covered with an optical coat work (Fig. 4). On the head of some other bolts strain gauges were stuck which measured the plain biaxial stress state in the middle of the top surface of the head of the bolt (3.5 x 3 mm). The magnetic probe detected average stresses up to 0.1 mm depth in an area of 14 mm diameter in the middle of the head of the bolt. 

The distribution of the main stresses during the optical coat work stress examination method is illustrated by a section of a stress state in Fig. 5. 

In a general way, the identification of asbestos fibers can be performed through morphological examination, together with specific analytical methods to obtain the mineral composition and/or stmcture. Morphological characterization in itself usually does not constitute a reHable identification criteria (1). Hence, microscopic examination methods and other analytical approaches are usually combined. 

Examination Methods The code establishes the types of examinations for evaluating various types of imperfec tions (see Table 10-61). 

Magnetic Particle Examination. All accessible surfaces of the main load carrying components of the equipment shall be examined by a magnetic particle examination method or technique conforming to the requirements of ASTM E709 Recommended Practice for Magnetic Particle Examination. Acceptance limits shall be as agreed upon by the manufacturer and the purchaser. 

Ultrasonic Examination. Main load carrying components of the equipment shall be ultrasonically examined in accordance with applicable ASTM standards. The extent of examination, method of examination, and basis for acceptance shall be agreed upon by the manufacturer and purchaser. 

This may be due, in part, to the limited information on toxic effects associated with such exposures. If additional information becomes available indicating adverse health effects of long-term exposures, then studies examining methods for mitigating the effects of such exposures would become a data need. 

Having defined particles and partical distributions, we now examine methods by which we can measure peuticles and properties of powders. There are four (4) primary methods used to obtain data concerning particle size distributions. These include ... 

Sham, Y.Y. Shao, Z.T. Tao, H. Warshel, A., Examining methods for calculations of binding free energies LRA, LIE and PDLD/S-LRA calculations of ligand binding to an HIV protease, Proteins 2000, 39, 393-407... 

Any of the examination methods described in para. GR-4.3.4 may be specified by the engineering design to supplement the examination required by Part IP or PL. Supplementary examination to be performed and any acceptance criteria that exceed the requirements in the applicable Part(s) shall be specified in the engineering design. 

Practice for Liquid Penetrant Inspection Method Practice for Magnetic Particle Examination Quality Standard for Steel Castings and Forgings for Valves, Flanges and Fittings and Other Piping Components — Magnetic Particle Examination Method... 

It is fortunate that most applications devolve into one of two camps small molecules or proteins. In the former case, the size of these molecules has stayed fairly constant and the inexorable rise in magnetic fields has meant that the number of incidences of second-order spectra has decreased (although complications will always exist with virtual couplings). It is therefore pertinent to examine methods, which are not only designed to extract couplings from first-order spectra, but are also amenable to automation. 

Studies examining reproductive effects in animals are invariably lengthy and initially catch all. An effect of reduced pregnancy rates in treated females having mated with treated males may be the result of a number of factors that would have to be examined methodically. 

Ikeda, M., Aiba, T., Ikui, A., Kurono, Y., Sakagami, M., Takeda, N., and Tomita, H. (2005). Taste disorders A survey of the examination methods and treatments used in Japan. Acta Otolaryngol. 125,1203-1210. 

Concentration of total protein in cerebrospinal fluid is an essential biochemical parameter. It is impossible to agree with the opinion of some clinicians (many of whom are fascinated by the latest examination methods) that this is an unnecessary parameter. It is tme that the concentration of total protein in cerebrospinal fluid varies with respect to the reference range. It is known that the concentration of total protein in cerebrospinal fluid exceeding 1 g represents a principal challenge to the diagnosis of some CNS diseases (e.g., multiple sclerosis). This is fully in accordance with the results of a study (A24) in which the highest detectable level of total protein was 0.92 g... 

TABLE 10"53 Acceptance Criteria for Welds and Examination Methods for Evaluating Weld Imperfections ... 

---