Electroplating continued

The depressed prices of most metals in world markets in the 1980s and early 1990s have slowed the development of new metal extraction processes, although the search for improved extractants continues. There is a growing interest in the use of extraction for recovery of metals from effluent streams, for example the wastes from pickling plants and electroplating (qv) plants (276). Recovery of metals from Hquid effluent has been reviewed (277), and an AM-MAR concept for metal waste recovery has recentiy been reported (278). Possible appHcations exist in this area for Hquid membrane extraction (88) as weU as conventional extraction. Other schemes proposed for effluent treatment are a wetted fiber extraction process (279) and the use of two-phase aqueous extraction (280). 

Although most nickel sensitization results from nonoccupational exposures, nickel dermatitis was historically a problem in workplaces where there was a high risk of continuous contact with soluble nickel, eg, in electroplating (qv) shops. Improved personal and industrial hygiene has largely eliminated this problem. However, there are a few occupations involving wet nickel work, particularly where detergents faciUtate the penetration of skin by nickel, where hand eczema may occur (126). 

Potassium cyanide [151 -50-8] KCN, a white crystalline, deUquescent soHd, was initially used as a flux, andlater for electroplating, which is the single greatest use in the 1990s. The demand for potassium cyanide was met by the ferrocyanide process until the latter part of the nineteenth century, when the extraordinary demands of the gold mining industry for alkah cyanide resulted in the development of direct synthesis processes. When cheaper sodium cyanide became available, potassium cyanide was displaced in many uses. With the decline in the use of alkah cyanides for plating the demand for potassium cyanide continues to decline. The total world production in 1990 was estimated at about 4500 t, down from 7300 t in 1976. 

There has been a continual increase in size and complexity of PCBs with a concurrent reduction in conductor and hole dimensions. Conductors can be less than 250 p.m wide some boards have conductors less than 75 pm wide. Multilayer boards greater than 2.5 mm thick having hole sizes less than 250 pm are being produced. This trend may, however, eventually cause the demise of the subtractive process. It is difficult to etch such fine lines using 35-pm copper foils, though foils as thin as 5 pm are now available. It is also difficult to electroplate holes having high aspect ratio. These factors may shift production to the semiadditive or fully additive processes. 

Zinc. Supphers of 2inc electroplating chemicals have reported that 2inc electroplating volumes continue to grow. More recendy, electroplated 2inc alloys have been promoted. Zinc was priced at 1.50/kg in eady 1993 (see Zinc and zinc alloys). 

The isothiazole ring does not occur in nature. By far the most important synthetic isothiazole derivative is saccharin. This was the first non-carbohydrate sweetening agent to be discovered, as long ago as 1879. It is about 300 times as sweet as sucrose, and is still used in many countries as a non-nutritive sweetener. After it was found that administration of massive doses to rats caused bladder cancer, its use was banned in the New World, but the controversy continues as to whether there is any danger when it is used in small quantity. Saccharin is also used as an additive in electroplating processes (73AHC(15)233). 

In Western Europe the largest user is the vehicle construction industry where ABS has been used for fascia panels, door covers, door handles, radiator grilles, ventilation system components, heater housings, seat belt fastenings, console panels, loudspeaker housings, interior trim and other uses. For some years there was extensive use of electroplated ABS. Whilst this continues to be used for nameplates, reflectors and other parts where a bright reflecting surface is a requirement, it has tended to fall out of favour simply for decoration. 

Nowadays, however, zinc-coated steel sheets, either continuously galvanised or electroplated, are often used as a basis material for overcoating with plastic materials or paints. The coatings are usually applied continuously and have a range of uses both externally and internally. Many surface finishes are obtainable, e.g. plain or embossed, and in an extensive range of colours, to suit almost any requirement . 

Specification for electroplated coatings of 65/35 tin/nickel alloy Method for the evaluation of results of accelerated corrosion tests on metallic coatings Methods of test for paints Cross-cut test Pull-off test for adhesion Resistance to artificial weathering (enclosed carbon arc) and Addendum No. 1 Resistance to continuous salt spray Notes for guidance on the conduct of natural weathering test... 

---