Acid electrolyte fuel cell

Phosphoric Acid Fuel Cell. Concentrated phosphoric acid is used for the electrolyte ia PAFC, which operates at 150 to 220°C. At lower temperatures, phosphoric acid is a poor ionic conductor (see Phosphoric acid and the phosphates), and CO poisoning of the Pt electrocatalyst ia the anode becomes more severe when steam-reformed hydrocarbons (qv) are used as the hydrogen-rich fuel. The relative stabiUty of concentrated phosphoric acid is high compared to other common inorganic acids consequentiy, the PAFC is capable of operating at elevated temperatures. In addition, the use of concentrated (- 100%) acid minimizes the water-vapor pressure so water management ia the cell is not difficult. The porous matrix used to retain the acid is usually sihcon carbide SiC, and the electrocatalyst ia both the anode and cathode is mainly Pt. 

Phosphoric Acid Fuel Cell This type of fuel cell was developed in response to the industiy s desire to expand the natural-gas market. The electrolyte is 93 to 98 percent phosphoric acid contained in a matrix of silicon carbide. The electrodes consist of finely divided platinum or platinum alloys supported on carbon black and bonded with PTFE latex. The latter provides enough hydrophobicity to the electrodes to prevent flooding of the structure by the electrolyte. The carbon support of the air elec trode is specially formulated for oxidation resistance at 473 K (392°F) in air and positive potentials. 

In a simple version of a fuel cell, a fuel such as hydrogen gas is passed over a platinum electrode, oxygen is passed over the other, similar electrode, and the electrolyte is aqueous potassium hydroxide. A porous membrane separates the two electrode compartments. Many varieties of fuel cells are possible, and in some the electrolyte is a solid polymer membrane or a ceramic (see Section 14.22). Three of the most promising fuel cells are the alkali fuel cell, the phosphoric acid fuel cell, and the methanol fuel cell. 

If an acid electrolyte is used, water is produced only at the cathode. An example is the phosphoric acid fuel cell ... 

Fhosphoric acid does not have all the properties of an ideal fuel cell electrolyte. Because it is chemically stable, relatively nonvolatile at temperatures above 200 C, and rejects carbon dioxide, it is useful in electric utility fuel cell power plants that use fuel cell waste heat to raise steam for reforming natural gas and liquid fuels. Although phosphoric acid is the only common acid combining the above properties, it does exhibit a deleterious effect on air electrode kinetics when compared with other electrolytes ( ) including such materials as sulfuric and perchloric acids, whose chemical instability at T > 120 C render them unsuitable for utility fuel cell use. In the second part of this paper, we will review progress towards the development of new acid electrolytes for fuel cells. 

Medium-temperature phosphoric acid fuel cells (PAFCs). The electrolyte is 85 to 95% phosphoric acid the working temperatures are 180 to 200°C. Such systems were used to build numerous autonomous power plants with an output of up to about 250 kW, and even some with an output of up to 4 MW, in the United States, Japan, and other countries. 

Phosphoric acid fuel cell (PAFC) Poison <0.5% olefins n.i. n.i. Poison <0.2 mol% (NH4)3P04 in electrolyte Poison <4 ppm73 Poison <4 ppm73... 

Phosphoric acid fuel cells use phosphoric acid as an electrolyte and have an OT of 190 to 210°C. 

This survey focuses on recent developments in catalysts for phosphoric acid fuel cells (PAFC), proton-exchange membrane fuel cells (PEMFC), and the direct methanol fuel cell (DMFC). In PAFC, operating at 160-220°C, orthophosphoric acid is used as the electrolyte, the anode catalyst is Pt and the cathode can be a bimetallic system like Pt/Cr/Co. For this purpose, a bimetallic colloidal precursor of the composition Pt50Co30Cr20 (size 3.8 nm) was prepared by the co-reduction of the corresponding metal salts [184-186], From XRD analysis, the bimetallic particles were found alloyed in an ordered fct-structure. The elecbocatalytic performance in a standard half-cell was compared with an industrial standard catalyst (bimetallic crystallites of 5.7 nm size) manufactured by co-precipitation and subsequent annealing to 900°C. The advantage of the bimetallic colloid catalysts lies in its improved durability, which is essential for PAFC applicabons. After 22 h it was found that the potential had decayed by less than 10 mV [187],... 

PAFC PEMFC PFC PGM PHEV PISI PM POX ppm PPP Phosphoric-acid fuel cell Proton-exchange-membrane fuel cell Polymer-electrolyte membrane Perfluorocarbons Platinum-group metals Plug-in hybrid-electric vehicle Port-injection spark ignition Particulate matter Partial oxidation Parts per million Purchasing power parity... 

Progress continues in fuel cell technology since the previous edition of the Fuel Cell Handbook was published in November 1998. Uppermost, polymer electrolyte fuel cells, molten carbonate fuel cells, and solid oxide fuel cells have been demonstrated at commercial size in power plants. The previously demonstrated phosphoric acid fuel cells have entered the marketplace with more than 220 power plants delivered. Highlighting this commercial entry, the phosphoric acid power plant fleet has demonstrated 95+% availability and several units have passed 40,000 hours of operation. One unit has operated over 49,000 hours. 

Fuel cells are typically classified by the type of electrolyte. Apart from certain specialty types, the five major types of fuel cells are alkaline fuel cell (AFC), polymer electrolyte fuel cell (PEMFC), phosphoric acid fuel cell (PAFC), molten carbonate fuel cell (MCFC), and solid oxide fuel cell (SOFC). 

The beginning of modeling of polymer-electrolyte fuel cells can actually be traced back to phosphoric-acid fuel cells. These systems are very similar in terms of their porous-electrode nature, with only the electrolyte being different, namely, a liquid. Giner and Hunter and Cutlip and co-workers proposed the first such models. These models account for diffusion and reaction in the gas-diffusion electrodes. These processes were also examined later with porous-electrode theory. While the phosphoric-acid fuel-cell models became more refined, polymer-electrolyte-membrane fuel cells began getting much more attention, especially experimentally. 

The final 0-D equation presented here stems from incorporating the gas-pressure dependences directly instead of through a limiting current density, which normally only considers oxygen effects. This equation was proposed by Newmanfor phosphoric-acid fuel cells and predates the above polymer—electrolyte fuel-cell expressions. It has the form... 

The earliest models of fuel-cell catalyst layers are microscopic, single-pore models, because these models are amenable to analytic solutions. The original models were done for phosphoric-acid fuel cells. In these systems, the catalyst layer contains Teflon-coated pores for gas diffusion, with the rest of the electrode being flooded with the liquid electrolyte. The single-pore models, like all microscopic models, require a somewhat detailed microstructure of the layers. Hence, effective values for such parameters as diffusivity and conductivity are not used, since they involve averaging over the microstructure. 

Phosphoric acid fuel cell (PAFC) working at 180-200 °C vfith a porous matrix of PTFE-bonded silicon carbide impregnated with phosphoric acid as electrolyte, conducting by the H cation. This medium-temperature fuel cell is now commercialized by ONSI (USA), mainly for stationary applications. 

Phosphoric acid fuel cells (PAFC) use liquid phosphoric acid as an electrolyte - the acid is contained in a Teflon-bonded silicon carbide matrix - and porous carbon electrodes containing a platinum catalyst. The PAFC is considered the "first generation" of modern fuel cells. It is one of the most mature cell types, the first to be used commercially, and features the most proven track record in terms of commercial applications with over 200 units currently in use. This type of fuel cell is typically used for stationary power generation, but some PAFCs have been used to power large vehicles such as city buses. 

Unlike alkaline, phosphoric acid, and polymer electrolyte membrane fuel cells, MCFCs don t reguire an external reformerto convert more energy-dense fuels to hydrogen. Due to the high temperatures at which they operate, these fuels are converted to hydrogen within the fuel cell itself by a process called internal reforming, which also reduces cost. 

Why is concentrated phosphoric acid preferred over other aqueous acid media as the electrolyte in aqueous acid fuel cells ... 

Phosphoric acid fuel cell (PAFC)—Phosphoric acid electrolyte with platinum catalyst. It can use hydrocarbon fuel and is suited for stationary applications. It can generate both electricity and steam. As many as 200 units in sizes ranging from 200 kW to 1 mW are in operation. 

---