Electrochemical advantages

On metals in particular, the dependence of the radiation absorption by surface species on the orientation of the electrical vector can be fiilly exploited by using one of the several polarization techniques developed over the past few decades [27, 28, 29 and 30], The idea behind all those approaches is to acquire the p-to-s polarized light intensity ratio during each single IR interferometer scan since the adsorbate only absorbs the p-polarized component, that spectral ratio provides absorbance infonnation for the surface species exclusively. Polarization-modulation mediods provide the added advantage of being able to discriminate between the signals due to adsorbates and those from gas or liquid molecules. Thanks to this, RAIRS data on species chemisorbed on metals have been successfidly acquired in situ under catalytic conditions [31], and even in electrochemical cells [32]. 

Other techniques to detennine the corrosion rate use instead of DC biasing, an AC approach (electrochemical impedance spectroscopy). From the impedance spectra, the polarization resistance (R ) of the system can be detennined. The polarization resistance is indirectly proportional to j. An advantage of an AC method is given by the fact that a small AC amplitude applied to a sample at the corrosion potential essentially does not remove the system from equilibrium. 

Electrolytic Reductions. Both nitro compounds and nitriles can be reduced electrochemically. One advantage of electrochemical reduction is the cleanness of the operation. Since there are a minimum of by-products, both waste disposal and purification of the product are greatiy simplified. However, unless very cheap electricity is available, these processes are generally too expensive to compete with the traditional chemical methods. 

In general, however, the electrochemical reduction of nitriles offers no significant advantages over traditional chemical methods and has not been widely used. 

Immobilized Enzymes. The immobilized enzyme electrode is the most common immobilized biopolymer sensor, consisting of a thin layer of enzyme immobilized on the surface of an electrochemical sensor as shown in Figure 6. The enzyme catalyzes a reaction that converts the target substrate into a product that is detected electrochemicaHy. The advantages of immobilized enzyme electrodes include minimal pretreatment of the sample matrix, small sample volume, and the recovery of the enzyme for repeated use (49). Several reviews and books have been pubHshed on immobilized enzyme electrodes (50—52). 

The industrial economy depends heavily on electrochemical processes. Electrochemical systems have inherent advantages such as ambient temperature operation, easily controlled reaction rates, and minimal environmental impact (qv). Electrosynthesis is used in a number of commercial processes. Batteries and fuel cells, used for the interconversion and storage of energy, are not limited by the Carnot efficiency of thermal devices. Corrosion, another electrochemical process, is estimated to cost hundreds of millions of dollars aimuaUy in the United States alone (see Corrosion and CORROSION control). Electrochemical systems can be described using the fundamental principles of thermodynamics, kinetics, and transport phenomena. 

There have been a number of cell designs tested for this reaction. Undivided cells using sodium bromide electrolyte have been tried (see, for example. Ref. 29). These have had electrode shapes for in-ceU propylene absorption into the electrolyte. The chief advantages of the electrochemical route to propylene oxide are elimination of the need for chlorine and lime, as well as avoidance of calcium chloride disposal (see Calcium compounds, calcium CHLORIDE Lime and limestone). An indirect electrochemical approach meeting these same objectives employs the chlorine produced at the anode of a membrane cell for preparing the propylene chlorohydrin external to the electrolysis system. The caustic made at the cathode is used to convert the chlorohydrin to propylene oxide, reforming a NaCl solution which is recycled. Attractive economics are claimed for this combined chlor-alkali electrolysis and propylene oxide manufacture (135). 

The use of impedance electrochemical techniques to study corrosion mechanisms and to determine corrosion rates is an emerging technology. Elec trode impedance measurements have not been widely used, largely because of the sophisticated electrical equipment required to make these measurements. Recent advantages in micro-elec tronics and computers has moved this technique almost overnight from being an academic experimental investigation of the concept itself to one of shelf-item commercial hardware and computer software, available to industrial corrosion laboratories. 

Generally, plastics have excellent resistance to weak mineral acids and are unaffected by inorganic salt solutions—areas where metals are not entirely suitable. Since plastics do not corrode in the electrochemical sense, they offer another advantage over metals most metals are affected by slight changes in pH, or minor impurities, or oxygen content, while plastics will remain resistant to these same changes. 

Catalytic oxidation reactions in ionic liquids have been investigated only very recently. This is somewhat surprising in view of the well loiown oxidation stability of ionic liquids, from electrochemical studies [11], and the great commercial importance of oxidation reactions. Moreover, for oxidation reactions with oxygen, the nonvolatile nature of the ionic liquid is of real advantage for the safety of the reaction. While the application of volatile organic solvents may be restricted by the formation of explosive mixtures in the gas phase, this problem does not arise if a nonvolatile ionic liquid is used as the solvent. 

The combined action of chemical (or electrochemical) treatment and scrubbing is often more effective than either method alone. It is frequently advantageous to alternate short periods of immersion with scrubbing to remove any corrosion product that has become loosened by the action of the chemical reagent. 

---