Electrocatalysts electrocatalyst types

Fig. 1.5 The effect of electrocatalyst type upon the anodic oxidation of propane in 3 M sulfuric acid at 80 °C.

In redox flow batteries such as Zn/Cl2 and Zn/Br2, carbon plays a major role in the positive electrode where reactions involving Cl2 and Br2 occur. In these types of batteries, graphite is used as the bipolar separator, and a thin layer of high-surface-area carbon serves as an electrocatalyst. Two potential problems with carbon in redox flow batteries are (i) slow oxidation of carbon and (ii) intercalation of halogen molecules, particularly Br2 in graphite electrodes. The reversible redox potentials for the Cl2 and Br2 reactions [Eq. (8) and... 

Binary systems of ruthenium sulfide or selenide nanoparticles (RujcSy, RujcSey) are considered as the state-of-the-art ORR electrocatalysts in the class of non-Chevrel amorphous transition metal chalcogenides. Notably, in contrast to pyrite-type MS2 varieties (typically RUS2) utilized in industrial catalysis as effective cathodes for the molecular oxygen reduction in acid medium, these Ru-based cluster materials exhibit a fairly robust activity even in high methanol content environments of fuel cells. 

The change in the electronic properties of Ru particles upon modification with Se was investigated recently by electrochemical nuclear magnetic resonance (EC-NMR) and XPS [28]. In this work, it was established for the first time that Se, which is a p-type semiconductor in elemental form, becomes metallic when interacting with Ru, due to charge transfer from Ru to Se. On the basis of this and previous results, the authors emphasized that the combination of two or more elements to induce electronic alterations on a major catalytic component, as exemplified by Se addition on Ru, is quite a promising method to design stable and potent fuel cell electrocatalysts. 

Finally, a simple method for a rapid evaluation of the activity of high surface area electrocatalysts is to observe the electrocatalytic response of a dispersion of carbon-supported catalyst in a thin layer of a recast proton exchange membrane.This type of electrode can be easily obtained from a solution of Nafion. As an example. Fig. 11 gives the comparative... 

In addition to these different types of alloys, some studies were also devoted to alternatives to platinum as electrocatalysts. Unfortunately, it is clear that even if some catalytic activities were observed, they are far from those obtained with platinum. Nickel tungsten carbides were investigated, but the electrocatalytic activity recorded for methanol oxidation was very low. Tungsten carbide was also considered as a possible alternative owing to its ability to catalyze the electrooxidation of hydrogen. However, it had no activity for the oxidation of methanol and recently some groups showed that a codeposit of Pt and WO3 led to an enhancement of the activity of platinum. ... 

Similarly, Pd, Ag, and Pd-Ag nanoclusters on alumina have been prepared by the polyol method [230]. Dend-rimer encapsulated metal nanoclusters can be obtained by the thermal degradation of the organic dendrimers [368]. If salts of different metals are reduced one after the other in the presence of a support, core-shell type metallic particles are produced. In this case the presence of the support is vital for the success of the preparation. For example, the stepwise reduction of Cu and Pt salts in the presence of a conductive carbon support (Vulcan XC 72) generates copper nanoparticles (6-8 nm) that are coated with smaller particles of Pt (1-2 nm). This system has been found to be a powerful electrocatalyst which exhibits improved CO tolerance combined with high electrocatalytic efficiency. For details see Section 3.7 [53,369]. 

The prevalence of the heme in O2 metabolism and the discovery in the 1960s that metallophthalocyanines adsorbed on graphite catalyze four-electron reduction of O2 have prompted intense interest in metaUoporphyrins as molecular electrocatalysts for the ORR. The technological motivation behind this work is the desire for a Pt-ffee cathodic catalyst for low temperature fuel cells. To date, three types of metaUoporphyrins have attracted most attention (i) simple porphyrins that are accessible within one or two steps and are typically available commercially (ii) cofacial porphyrins in which two porphyrin macrocycles are confined in an approximately stacked (face-to-face) geometry and (iii) biomimetic catalysts, which are highly elaborate porphyrins designed to reproduce the stereoelectronic properties of the 02-reducing site of cytochrome oxidase. 

PB and its derivatives are of interest for a variety of reasons, the most important of which is its electrochromism [93]. In addition, it is an electrocatalyst for several different types of substrates, notably hydrogen peroxide, as will be seen below. Synthesis of nanopartides of Prussian Blue is relatively straightforward. It relies on many of the prindples of colloid chemistry, and produces ionically stabilized colloidal solutions (Figure 4.7). As a consequence, the electrochemical behavior of PB N Ps has been examined by several groups. In this section, we discuss the behavior of P B N Ps immobilized at electrodes. 

Electrochemical reactions take place at the catalyst layers of the fuel cell. At the anode and cathode, hydrogen is oxidized (eq 1) and oxygen is reduced (eq 2), respectively. These layers are often the thinnest in the fuel-cell sandwich but are perhaps the most complex because this is where electrochemical reactions take place and where all of the different types of phases exist. Thus, the membrane and diffusion media models must be used in the catalyst layer along with additional expressions related to the electrochemical kinetics on the supported electrocatalyst particles. 

A schematic of a typical fuel-cell catalyst layer is shown in Figure 9, where the electrochemical reactions occur at the two-phase interface between the electrocatalyst (in the electronically conducting phase) and the electrolyte (i.e., membrane). Although a three-phase interface between gas, electrolyte, and electrocatalyst has been proposed as the reaction site, it is now not believed to be as plausible as the two-phase interface, with the gas species dissolved in the electrolyte. This idea is backed up by various experimental evidence, such as microscopy, and a detailed description is beyond the scope of this review. Experimental evidence also supports the picture in Figure 9 of an agglomerate-type structure where the electrocatalyst is supported on a carbon clump and is covered by a thin layer of membrane. Sometimes a layer of liquid water is assumed to exist on top of the membrane layer, and this is discussed in section 4.4.6. Figure 9 is an idealized picture, and... 

Another prospect for eflBcient energy conversion is the fuel cell. The diflFerent types of fuel cells presently under study or development were reviewed by G. Belanger of Hydro-Quebec, who concluded that commercial availability of such units is now in sight. However, the need to develop cheap, efficient electrocatalysts for oxygen reduction remains. 

Figure 3. Schematic of fuel-cells electrodes design (a) metal electrode with two types of pores (b) composite electrode with dispersed electrocatalysts...

Transition-metal -phthalocyanines as catalysts in acid medium. To prevent carbonate formation by the carbon dioxide in the air or that produced by oxidation of carbonaceous fuels, an acid electrolyte is necessary hence it is important to find electrocatalysts for an acid medium. Independently of Jasinski, we were soon able to show 3>4> that under certain conditions the reduction of oxygen in dilute sulfuric acid proceeded better with phthalocyanines on suitable substrates than with platinum metal. The purified phthalocyanines were dissolved in concentrated sulfuric acid and precipitated on to the carbon substrate by addition of water. This coated powder was made into porous electrodes bound with polyethylene and having a geometrical surface of 5 cm2 (cf. Section 2.2.2.1.). The results obtained with compact electrodes of this type are shown in Fig. 6. 

Despite extensive studies, the photovoltage or the solar-to-chemical energy conversion efficiency still remains relatively low. The main reason is that it is very difficult to meet all requirements for high efficiency. For example, high catalytic activity and sufficient passivation at the electrode surface are incompatible. It was found, however, that a semiconductor electrode modified with small metal particles can meet all the requirements and thus becomes an ideal type semiconductor electrode. Cu, Ag, and Au were chosen because they were reported to work as efficient electrocatalysts for the C02 reduction. p-Si electrodes modified with these metals in C02-staurated aqueous electrolyte under illumination produce mainly methane and ethylene.178 This is similar to the metal electrodes but the metal-particle-coated electrodes work at approximately 0.5 V more positive potentials, contrary to continuous metal-coated p-Si electrodes. 

This type of N-doped soot catalyst is of particular interest for the development of advanced fuel cells. As this type of catalyst is not poisoned by carbon monoxide, it is a promising candidate for O2 cathodes in methanolconsuming fuel cells (132). In methanol-combusting cells, diffusive transport of methanol from the anode to the cathode cannot be avoided, with the consequence that the activity of Pt-activated cathodes becomes severely impaired by CO poisoning of the Pt catalyst therefore, a CO-insensitive cathodic electrocatalyst seems to be indispensible. Yet the longevity of this type of catalyst is still in dispute (133). 

---