Documentation, fabrication

Technical Guidance Document Fabrication of Polyethylene FML U.S. Environmental Protection Agency, 1989, EPA/530/S W-89/069. 

Searching a crime scene is a complex process (25), involving poHce, crime scene technicians, and forensic scientists. The procedure requires careful documentation, collection, and preservation of the evidence. Trace evidence (26) in criminal investigations typically consists of hairs (27,28) both natural and synthetic fibers (qv) (29,30), fabrics glass (qv) (31,32) plastics (33) sod plant material budding material such as cement (qv), paint (qv), stucco, wood (qv), etc (34), flammable fluid residues (35,36), eg, in arson investigations explosive residues, eg, from bombings (37,38) (see Explosives and propellents), and so on. 

Years of development have led to a standardized system for objective evaluation of fabric hand (129). This, the Kawabata evaluation system (KES), consists of four basic testing machines a tensile and shear tester, a bending tester, a compression tester, and a surface tester for measuring friction and surface roughness. To complete the evaluation, fabric weight and thickness are determined. The measurements result in 16 different hand parameters or characteristic values, which have been correlated to appraisals of fabric hand by panels of experts (121). Translation formulas have also been developed based on required levels of each hand property for specific end uses (129). The properties include stiffness, smoothness, and fullness levels as well as the total hand value. In more recent years, abundant research has been documented concerning hand assessment (130—133). 

Do record the issue status of documents used to fabricate product. 

Accepted solutions are usually covered by specifications and codes of practice. These documents are important for three reasons they form part of the contract they define methods of design and fabrication proven by experience and they act as a means of communication between the parties involved in design, fabrication, construction and inspection. There is a strong incentive to use standard solutions as unexpected problems or misunderstandings are less likely to occur than if a novel solution is attempted such problems lead to the cost of rectification, but the delay that they cause is usually more importantConsequently project managers are often reluctant to be the first to use a novel solution. 

BS 6374 Part 5 1985 gives full details of design and fabrication requirements and it is advisable to consult this document as well as the lining contractor prior to arriving at the final design. 

One of the important aspects of the development of P-plastomers was the expectation that these materials were amenable to plastics processing such as fiber and film formation and yet would yield soft elastic fabrication. This combination was hitherto unknown [24]. The formation of nonwoven fabrics including spun-bond and melt-blown nonwoven fabrics as well as their laminated forms has been documented. Similarly, cast film operation to form elastic monolithic films or composite structures which are not only amenable to these processes, but also to a variety of postfabrication processes have been described. 

Why does the amount of acid in paper make such a difference Acids are corrosive chemicals. Corrosive chemicals can destroy material or living tissue on contact. Paper does not contain enough acid to burn skin, but over time the paper becomes stiff and brittle and eventually falls apart. As a result, precious personal memories or important historical documents that were written on acidic paper can be lost. Acid-containing paper can also transfer the acid to other objects in a process called acid migration. The acid can weaken or destroy the fibers in fabrics. It can also ruin photographs. Therefore, to preserve those irreplaceable memories, be sure to use paper that is acid-free. 

Procurement Fabrication Construction vendor and fabrication documents inspection reports field change documents vendor data on equipment as built data What-If, Checklist... 

The design, materials, fabrication, assembly, examination, inspection, and testing requirements of this Code are not applicable to components manufactured in accordance with the documents listed in Table IP-8.1, unless specifically stated in this Code or the listed document. 

Inspections by owner include inspections, verifications, and audits of the construction of piping systems, which include fabrication, welding, heat treatment, assembly, erection, examination, and testing, in addition to the construction organization s documented procedures, personnel qualifications, and quality control records. 

The most important electrokinetic data pertinent to fuel cell models are the specific interfacial area in the catalyst layer, a, the exchange current density of the oxygen reduction reaction (ORR), io, and Tafel slope of ORR. The specific interfacial area is proportional to the catalyst loading and inversely proportional to the catalyst layer thickness. It is also a strong function of the catalyst layer fabrication methods and procedures. The exchange current density and Tafel slope of ORR have been well documented in refs 28—31. 

Methods of synthesis, fabrication, or derivation as well as identity (if estabhshed), strength, and purity characteristics of the material must be documented. Copies of this documentation must be included with study records and must be available for FDA inspection. In the case of contract testing facilities in which for proprietary reasons the sponsor may not wish to release such information to the contract lab, the contract facility should have written assurance from the sponsor that such documentation exists. 

Jametel, M., Chen-ki-souen. L encre de Chine son Histoire et sa Fabrication, d apres des Documents Chinois, Paris, 1882 translation into French of Shen Chi-sun, Mo-fa chi-yao (1398). 

---