Dicarboxylic acid catalysts

In 2007, Maruoka et al. introduced chiral dicarboxylic acids consisting of two carboxylic acid functionalities and an axially chiral binaphthyl moiety. They applied this new class of chiral Brpnsted acid catalyst to the asymmetric alkylation of diazo compounds withA-Boc imines [91]. The preparation of the dicarboxylic acid catalysts bearing aryl groups at the 3,3 -positions of the binaphthyl scaffold follows a synthetic route, which has been developed earlier in the Maruoka laboratory [92]. 

The benzoic acid derivative 457 is formed by the carbonylation of iodoben-zene in aqueous DMF (1 1) without using a phosphine ligand at room temperature and 1 atm[311]. As optimum conditions for the technical synthesis of the anthranilic acid derivative 458, it has been found that A-acetyl protection, which has a chelating effect, is important[312]. Phase-transfer catalysis is combined with the Pd-catalyzed carbonylation of halides[3l3]. Carbonylation of 1,1-dibromoalkenes in the presence of a phase-transfer catalyst gives the gem-inal dicarboxylic acid 459. Use of a polar solvent is important[314]. Interestingly, addition of trimethylsilyl chloride (2 equiv.) increased yield of the lactone 460 remarkabiy[3l5]. Formate esters as a CO source and NaOR are used for the carbonylation of aryl iodides under a nitrogen atmosphere without using CO[316]. Chlorobenzene coordinated by Cr(CO)j is carbonylated with ethyl formate[3l7]. 

G-19 Dicarboxylic Acids. The C-19 dicarboxyhc acids are generally mixtures of isomers formed by the reaction of carbon monoxide on oleic acid. Since the reaction produces a mixture of isomers, no single chemical name can be used to describe them. Names that have been used include 2-nonyldecanedioic acid, 2-octylundecanedioic acid, l,8-(9)-heptadecanedicarboxyhc acid, and 9-(10)-carboxystearic acid. The name 9-(10)-carboxystearic acid can be used correctiy if the product is made with no double bond isomerization (rhodium triphenylphosphine catalyst system). 

Practically all pyridazine-carboxylic and -polycarboxylic acids undergo decarboxylation when heated above 200 °C. As the corresponding products are usually isolated in high yields, decarboxylation is frequently used as the best synthetic route for many pyridazine and pyridazinone derivatives. For example, pyridazine-3-carboxylic acid eliminates carbon dioxide when heated at reduced pressure to give pyridazine in almost quantitative yield, but pyridazine is obtained in poor yield from pyridazine-4-carboxylic acid. Decarboxylation is usually carried out in acid solution, or by heating dry silver salts, while organic bases such as aniline, dimethylaniline and quinoline are used as catalysts for monodecarboxylation of pyridazine-4,5-dicarboxylic acids. 

A wide range of polyether-polyamide block copolymers were first offered by Atochem in 1981 under the trade name Pebax. These are made by first producing a low molecular weight polyamide using an excess of dicarboxylic acid at a temperature above 230°C and under a pressure of up to 25 bar. This is then combined with a polyether by reaction at 230-280°C under vacuum (O.l-lOTorr) in the presence of a suitable catalyst such as Ti(OR)4. 

Ruthenium dioxide or ruthenium-on-carbon are effective catalysts for hydrogenation of mono- and dicarboxylic acids to the alcohol or glycol. High pressures (5,000-10,000 psig) and elevated temperatures (130-225 C) have been used in these hydrogenations 8,12,24). Yields of alcohol tend to be less than perfect because of esterification of the alcohol. Near quantitative yields of alcohol can be obtained by mixing ruthenium and copper chromite catalysts so as to reduce the ester as formed. 

Generally, both sodium methoxide and ethoxide are employed as basic catalysts, but sometimes potassium methoxide or sodium hydride67 is used. The alkali salts of the dicarboxylic acids are primarily formed, due to the basic reaction conditions, but after acidic workup the free acids are obtained in 20-60 % yield. Reesterification65 of the acids can be performed (see Section 2.1.4.3.). This method can also be applied to the synthesis of hetarenothiepins such as furanothiepins.67... 

Catalytic hydrogenation of dimethyl 3-methyl-3//-3-benzazepine-2,4-dicarboxylate (10) to the 1,2,4,5-tetrahydro derivative with hydrogen and a palladium-barium sulfate catalyst, followed by treatment of the reaction mixture with iodomethane in refluxing methanol, yields a mixture of the 2,4-dicarboxylic acid 11 and the methiodide salt 12.24... 

From the preceding discussion, it is easily understood that direct polyesterifications between dicarboxylic acids and aliphatic diols (Scheme 2.8, R3 = H) and polymerizations involving aliphatic or aromatic esters, acids, and alcohols (Scheme 2.8, R3 = alkyl group, and Scheme 2.9, R3 = H) are rather slow at room temperature. These reactions must be carried out in the melt at high temperature in the presence of catalysts, usually metal salts, metal oxides, or metal alkoxides. Vacuum is generally applied during the last steps of the reaction in order to eliminate the last traces of reaction by-product (water or low-molar-mass alcohol, diol, or carboxylic acid such as acetic acid) and to shift the reaction toward the... 

Activating agents, such as trifluoroacetic anhydride 1,1 -carbonyldiimidazolc carbodiimides sulfonyl, tosyl, and picryl chlorides and a range of phosphorus derivatives can promote direct solution reactions between dicarboxylic acids and diols or diphenols in mild conditions. The activating agents are consumed during the reaction and, therefore, do not act as catalysts. These so-called direct polycondensation or activation polycondensation reactions proceed via the in situ transformation of one of the reactants, generally the carboxylic acid, into a more... 

The paraffin wax is oxidized by air in a liquid phase process at 110-130°C. Catalysts for this radical reaction are cobalt or manganese salts [54]. The quality of the obtained mixture of homologous carboxylic acids is impaired by numerous byproducts such as aldehydes, ketones, lactones, esters, dicarboxylic acids, and other compounds. These are formed despite a partial conversion of the paraffin and necessitate an expensive workup of the reaction product [50,55]. 

The scope of this reaction is similar to that of 10-21. Though anhydrides are somewhat less reactive than acyl halides, they are often used to prepare carboxylic esters. Acids, Lewis acids, and bases are often used as catalysts—most often, pyridine. Catalysis by pyridine is of the nucleophilic type (see 10-9). 4-(A,A-Dimethylamino)pyridine is a better catalyst than pyridine and can be used in cases where pyridine fails. " Nonbasic catalysts are cobalt(II) chloride " and TaCls—Si02. " Formic anhydride is not a stable compound but esters of formic acid can be prepared by treating alcohols " or phenols " with acetic-formic anhydride. Cyclic anhydrides give monoesterified dicarboxylic acids, for example,... 

The dimethylbenzenes (xylenes) are very important industrial chemicals recovered during the refining of petroleum. All three xylenes are used to produce the corresponding aromatic dicarboxylic acids by reaction with oxygen over a catalyst. 

Long-chain unsaturated a,oo-dicarboxylic acid methyl esters and their epox-idized derivahves were polymerized with 1,3-propanediol or 1,4-butanediol in the presence of lipase CA catalyst to produce reachve polyesters. The molecular weight of the polymer from 1,4-butanediol was higher than that from... 

A novel chemoenzymatic route to polyester polyurethanes was developed without employing highly toxic isocyanate intermediates. First, diurethane diols were prepared from cyclic carbonates and primary diamines, which were subsequently polymerized with dicarboxylic acids and glycols by using lipase CA as catalyst, yielding the polyurethanes under mild reaction conditions. 

In the single-stage production of polyurethanes, di-, tri-, or polyisocyanates are mixed directly with molecules containing two or more reactive hydrogen atoms, such as diols, diamines, and dicarboxylic acids. We typically increase the reaction rate by adding amine or organotin based catalysts. The reaction normally occurs rapidly, evolving much heat. In order to ensure... 

In vitro synthesis of polyesters using isolated enzymes as catalyst via non-biosynthetic pathways is reviewed. In most cases, lipase was used as catalyst and various monomer combinations, typically oxyacids or their esters, dicarboxylic acids or their derivatives/glycols, and lactones, afforded the polyesters. The enzymatic polymerization often proceeded under mild reaction conditions in comparison with chemical processes. By utilizing characteristic properties of lipases, regio- and enantioselective polymerizations proceeded to give functional polymers, most of which are difficult to synthesize by conventional methodologies. 

The polymerization of dicarboxylic acids and glycols using lipase CA catalyst proceeded in a solvent-free system, despite the initial heterogeneous mixture of... 

The formation of relatively ill-defined catalysts for epoxide/C02 copolymerization catalysts, arising from the treatment of ZnO with acid anhydrides or monoesters of dicarboxylic acids, has been described in a patent disclosure.968 Employing the perfluoroalkyl ester acid (342) renders the catalyst soluble in supercritical C02.969 At 110°C and 2,000 psi this catalyst mixture performs similarly to the zinc bisphenolates, producing a 96 4 ratio of polycarbonate polyether linkages, with a turnover of 440 g polymer/g [Zn] and a broad polydispersity (Mw/Mn>4). Related aluminum complexes have also been studied and (343) was found to be particularly active. However, selectivity is poor, with a ratio of 1 3.6 polycarbonate polyether.970... 

The hydrolysis of esters by the nickel derivative (271) provided an early example of the use of a metal-capped cyclodextrin as a catalyst (shown here as its p-nitrophenyl acetate inclusion complex) (Breslow Overman, 1970 Breslow, 1971). The synthesis of this host involves the following steps (i) covalent binding of the pyridine dicarboxylic acid moiety to cyclodextrin, (ii) coordination of Ni(n) to this species, and (iii)... 

Hagiya et al. recently reported [20] the new decarboxylation catalyst of chrysanthemum dicarboxylic acid monomethyl ester (46) to give ethyl (Z)-norchrysanthemate (EIZ = 4/96) in 59% yield. This method efficiently gives (Z)-(l R)-lrans-norchrysanthemic acid, but the yield is still moderate and the starting chrysanthemum dicarboxylic acid monomethyl ester is not a commercial product (Scheme 7). 

Anthraquinone itself is traditionally available from the anthracene of coal tar by oxidation, often with chromic acid or nitric acid a more modern alternative method is that of air oxidation using vanadium(V) oxide as catalyst. Anthraquinone is also produced in the reaction of benzene with benzene-1,2-dicarboxylic anhydride (6.4 phthalic anhydride) using a Lewis acid catalyst, typically aluminium chloride. This Friedel-Crafts acylation gives o-benzoylbenzoic acid (6.5) which undergoes cyclodehydration when heated in concentrated sulphuric acid (Scheme 6.2). Phthalic anhydride is readily available from naphthalene or from 1,2-dimethylbenzene (o-xylene) by catalytic air oxidation. 

Compound 108 may be prepared directly from 104 without intermediate isolation of 104 by treating the dicarboxylic acid 107 with monohydrate or with concentrated sulfuric acid at 35°C, followed by bromination in the presence of iodine as a catalyst. 

---