Copolymerization phases

The copolymeric phases of PBTESI0.5, PBTDBS2, and PBTDBS9 blends have been recovered by centrifugation of the milky solutions. DSC traces relative to these copolymers are reported in Fig. 16. The copolymers extracted from the blends show an endothermic peak at 226°C, close to the melting point of plain PBT. In Fig. 17, FTIR spectra of the copolymers are... 

Generalized first-order kinetics have been extensively reviewed in relation to teclmical chemical applications [59] and have been discussed in the context of copolymerization [53]. From a theoretical point of view, the general class of coupled kinetic equation (A3.4.138) and equation (A3.4.139) is important, because it allows for a general closed-fomi solution (in matrix fomi) [49]. Important applications include the Pauli master equation for statistical mechanical systems (in particular gas-phase statistical mechanical kinetics) [48] and the investigation of certain simple reaction systems [49, ]. It is the basis of the many-level treatment of... 

An emulsion model that assumes the locus of reaction to be inside the particles and considers the partition of AN between the aqueous and oil phases has been developed (50). The model predicts copolymerization results very well when bulk reactivity ratios of 0.32 and 0.12 for styrene and acrylonitrile, respectively, ate used. 

Emulsion Process. The emulsion polymerization process utilizes water as a continuous phase with the reactants suspended as microscopic particles. This low viscosity system allows facile mixing and heat transfer for control purposes. An emulsifier is generally employed to stabilize the water insoluble monomers and other reactants, and to prevent reactor fouling. With SAN the system is composed of water, monomers, chain-transfer agents for molecular weight control, emulsifiers, and initiators. Both batch and semibatch processes are employed. Copolymerization is normally carried out at 60 to 100°C to conversions of - 97%. Lower temperature polymerization can be achieved with redox-initiator systems (51). 

Tetiafluoioethylene—peifluoiopiopyl vinyl ethei copolymeis [26655-00-5] aie made in aqueous (1,2) oi nonaqueous media (3). In aqueous copolymerizations water-soluble initiators and a perfluorinated emulsifying agent are used. Molecular weight and molecular weight distribution are controlled by a chain-transfer agent. Sometimes a second phase is added to the reaction medium to improve the distribution of the vinyl ether in the poljmier (11) a buffer is also added. 

The aqueous phase into which the monomer mix is dispersed is also prepared in a separate tank before transferring to the copolymerization ketde. It contains a catalyst, such as benzoyl peroxide [94-36-0], to initiate and sustain the polymerization reaction, and chemicals that aid in stabilizing the emulsion after the desired degree of dispersion is achieved. Careful adherence to predeterrnined reaction time and temperature profiles for each copolymer formulation is necessary to assure good physical durabiHty of the final ion-exchange product. 

Suspension Polymerization. At very low levels of stabilizer, eg, 0.1 wt %, the polymer does not form a creamy dispersion that stays indefinitely suspended in the aqueous phase but forms small beads that setde and may be easily separated by filtration (qv) (69). This suspension or pearl polymerization process has been used to prepare polymers for adhesive and coating appHcations and for conversion to poly(vinyl alcohol). Products in bead form are available from several commercial suppHers of PVAc resins. Suspension polymerizations are carried out with monomer-soluble initiators predominantly, with low levels of stabilizers. Suspension copolymerization processes for the production of vinyl acetate—ethylene bead products have been described and the properties of the copolymers determined (70). Continuous tubular polymerization of vinyl acetate in suspension (71,72) yields stable dispersions of beads with narrow particle size distributions at high yields. 

Thermoplastic elastomers are often multiphase compositions in which the phases are intimately dispersed. In many cases, the phases are chemically bonded by block or graft copolymerization. In others, a fine dispersion is apparentiy sufficient. In these multiphase systems, at least one phase consists of a material that is hard at room temperature but becomes fluid upon heating. Another phase consists of a softer material that is mbberlike at RT. A simple stmcture is an A—B—A block copolymer, where A is a hard phase and B an elastomer, eg, poly(styrene- -elastomer- -styrene). 

Copolymerizations of benzvalene with norhornene have been used to prepare block copolymers that are more stable and more soluble than the polybenzvalene (32). Upon conversion to (CH), some phase separation of nonconverted polynorhornene occurs. Other copolymerizations of acetylene with a variety of monomers and carrier polymers have been employed in the preparation of soluble polyacetylenes. Direct copolymeriza tion of acetylene with other monomers (33—39), and various techniques for grafting polyacetylene side chains onto solubilized carrier polymers (40—43), have been studied. In most cases, the resulting copolymers exhibit poorer electrical properties as solubiUty increases. 

The refined grade s fastest growing use is as a commercial extraction solvent and reaction medium. Other uses are as a solvent for radical-free copolymerization of maleic anhydride and an alkyl vinyl ether, and as a solvent for the polymerization of butadiene and isoprene usiag lithium alkyls as catalyst. Other laboratory appHcations include use as a solvent for Grignard reagents, and also for phase-transfer catalysts. 

In contrast to ionic chain polymerizations, free radical polymerizations offer a facile route to copolymers ([9] p. 459). The ability of monomers to undergo copolymerization is described by the reactivity ratios, which have been tabulated for many monomer systems for a tabulation of reactivity ratios, see Section 11/154 in Brandrup and Immergut [14]. These tabulations must be used with care, however, as reactivity ratios are not always calculated in an optimum manner [15]. Systems in which one reactivity ratio is much greater than one (1) and the other is much less than one indicate poor copolymerization. Such systems form a mixture of homopolymers rather than a copolymer. Uncontrolled phase separation may take place, and mechanical properties can suffer. An important ramification of the ease of forming copolymers will be discussed in Section 3.1. 

The effects of increasing the concentration of initiator (i.e., increased conversion, decreased M , and broader PDi) and of reducing the reaction temperature (i.e., decreased conversion, increased M , and narrower PDi) for the polymerizations in ambient-temperature ionic liquids are the same as observed in conventional solvents. May et al. have reported similar results and in addition used NMR to investigate the stereochemistry of the PMMA produced in [BMIM][PFgj. They found that the stereochemistry was almost identical to that for PMMA produced by free radical polymerization in conventional solvents [43]. The homopolymerization and copolymerization of several other monomers were also reported. Similarly to the findings of Noda and Watanabe, the polymer was in many cases not soluble in the ionic liquid and thus phase-separated [43, 44]. 

Heterogeneous copolymerization of acrylamide causes redistribution comonomers between phases I and II. This leads to a change of copolymer composition in phases I and II. As a result, the values of ri and change. This accounts for anomalous widening of the experimental composition distribution curves as compared with theoretical curves. 

The water solubilities of the functional comonomers are reasonably high since they are usually polar compounds. Therefore, the initiation in the water phase may be too rapid when the initiator or the comonomer concentration is high. In such a case, the particle growth stage cannot be suppressed by the diffusion capture mechanism and the solution or dispersion polymerization of the functional comonomer within water phase may accompany the emulsion copolymerization reaction. This leads to the formation of polymeric products in the form of particle, aggregate, or soluble polymer with different compositions and molecular weights. The yield for the incorporation of functional comonomer into the uniform polymeric particles may be low since some of the functional comonomer may polymerize by an undesired mechanism. 

Soapless seeded emulsion copolymerization has been proposed as an alternative method for the preparation of uniform copolymer microspheres in the submicron-size range [115-117]. In this process, a small part of the total monomer-comonomer mixture is added into the water phase to start the copolymerization with a lower monomer phase-water ratio relative to the conventional direct process to prevent the coagulation and monodispersity defects. The functional comonomer concentration in the monomer-comonomer mixture is also kept below 10% (by mole). The water phase including the initiator is kept at the polymerization temperature during and after the addition of initial monomer mixture. The nucleation takes place by the precipitation of copolymer macromolecules, and initially formed copolymer nuclei collide and form larger particles. After particle formation with the initial lower organic phase-water ratio, an oligomer initiated in the continuous phase is... 

An example of the liquid-phase polymerization is the Spheripol process (Figure 12-3), which uses a tubular reactor. Copolymerization... 

Figure 12-3. The Himont Inc. Spheripol process for producing polypropylene in a liquid-phase (1) tubular reactor, (2,4) two-stage flash pressure system (to separate unreacted monomer for recycle), (3) heterophasic copolymerization gas-phase reactor, (5) stripper.

Thermoplastic elastomers are multiphase composites, in which the phases are intimately depressed. In many cases, the phases are chemically bonded by block or graft copolymerization. At least one of the phases consists of a material that is hard at room temperature. ... 

The preparation and properties of a novel, commercially viable Li-ion battery based on a gel electrolyte has recently been disclosed by Bellcore (USA) [124]. The technology has, to date, been licensed to six companies and full commercial production is imminent. The polymer membrane is a copolymer based on PVdF copolymerized with hexafluoropropylene (HFP). HFP helps to decrease the crystallinity of the PVdF component, enhancing its ability to absorb liquid. Optimizing the liquid absorption ability, mechanical strength, and processability requires optimized amorphous/crystalline-phase distribution. The PVdF-HFP membrane can absorb plasticizer up to 200 percent of its original volume, especially when a pore former (fumed silica) is added. The liquid electrolyte is typically a solution of LiPF6 in 2 1 ethylene carbonate dimethyl car-... 

The formation mechanism of structure of the crosslinked copolymer in the presence of solvents described on the basis of the Flory-Huggins theory of polymer solutions has been considered by Dusek [1,2]. In accordance with the proposed thermodynamic model [3], the main factors affecting phase separation in the course of heterophase crosslinking polymerization are the thermodynamic quality of the solvent determined by Huggins constant x for the polymer-solvent system and the quantity of the crosslinking agent introduced (polyvinyl comonomers). The theory makes it possible to determine the critical degree of copolymerization at which phase separation takes place. The study of this phenomenon is complex also because the comonomers act as diluents. 

---