Capital cost temperature

If k-2 increases faster than kx, operate at low temperature (but beware of capital cost, since low temperature, although increasing selectivity, also increases reactor size). Here there is an economic tradeoff between decreasing byproduct formation and increasing capital cost. 

Increasing the chosen value of process energy consumption also increases all temperature differences available for heat recovery and hence decreases the necessary heat exchanger surface area (see Fig. 6.6). The network area can be distributed over the targeted number of units or shells to obtain a capital cost using Eq. (7.21). This capital cost can be annualized as detailed in App. A. The annualized capital cost can be traded off against the annual utility cost as shown in Fig. 6.6. The total cost shows a minimum at the optimal energy consumption. 

Direct Contact Heat Exchangers. In a direct contact exchanger, two fluid streams come into direct contact, exchange heat and maybe also mass, and then separate. Very high heat-transfer rates, practically no fouling, lower capital costs, and lower approach temperatures are the principal advantages. 

A low temperature of approach for the network reduces utihties but raises heat-transfer area requirements. Research has shown that for most of the pubhshed problems, utility costs are normally more important than annualized capital costs. For this reason, AI is chosen eady in the network design as part of the first tier of the solution. The temperature of approach, AI, for the network is not necessarily the same as the minimum temperature of approach, AT that should be used for individual exchangers. This difference is significant for industrial problems in which multiple shells may be necessary to exchange the heat requited for a given match (5). The economic choice for AT depends on whether the process environment is heater- or refrigeration-dependent and on the shape of the composite curves, ie, whether approximately parallel or severely pinched. In cmde-oil units, the range of AI is usually 10—20°C. By definition, AT A AT. The best relative value of these temperature differences depends on the particular problem under study. 

Some processes use only one reactor (57) or a combination of liquid- and vapor-phase reactors (58). The goal of these schemes is to reduce energy consumption and capital cost. Hydrogenation normally is carried out at 2—3 MPa (20—30 atm). Temperature is maintained at 300—350°C to meet a typical specification of less than 500 ppm benzene in the product at higher temperatures, thermodynamic equiUbrium shifts to favor benzene and the benzene specification is impossible to attain. Also, at higher temperatures, isomerization of cyclohexane to methylcyclopentane occurs typically there is a 200 ppm specification limit on methylcyclopentane content. 

The concept of an optimum reboiler or condenser AT relates to the fact that the value of energy changes with temperature. As the gap between supply and rejection widens, the real work in a distillation increases. The optimum AT is found by balancing this work penalty against the capital cost of bigger heat exchangers. 

Equipment Materials and Abrasion Resistance. Stainless steel, especially Type 316, is the constmction material of choice and can resist a variety of corrosive conditions and temperatures. Carbon steels are occasionally used. Rusting may, however, cause time-consuming maintenance and can damage mating locating surfaces, which increases the vibration and noise level. Titanium, HasteUoy, or high nickel alloys are used in special instances, at a considerable increase in capital cost. 

As of the mid-1990s, many older conventional steam plants have been converted to combined cycle. The old boiler is removed and replaced by a combustion turbine and heat recovery steam generator. Although the cycle efficiency is not as high as completely new plants, substantial capital cost is avoided by the modification and reuse of existing steam turbine and auxiHary equipment. In many combined cycle power plants, steam is injected into the combustors of the combustion turbine to lower peak flame temperatures and consequendy lower NO. ... 

Overall comparison between amine and carbonate at elevated pressures shows that the amine usually removes carbon dioxide to a lower concentration at a lower capital cost but requires more maintenance and heat. The impact of the higher heat requirement depends on the individual situation. In many appHcations, heat used for regeneration is from low temperature process gas, suitable only for boiler feed water heating or low pressure steam generation, and it may not be usefiil in the overall plant heat balance. 

As an example, the battery-limits capital cost can be estimated for the production of 10,000 t/yr of ethylene (qv) from ethanol (11). Seven processing blocks, ie, vaporizer, reactor, water quench, compressor, dryer, distillation, and energy recovery, can be identified. The highest temperature is 350°C (reactor), and the highest pressure is about 1.7 MPa (17 atm) (compressor, two towers). If a materials-pressure factor, + of 1.03 is assumed, then for N = 7 0 = 0.87 1/0 = 1 64 and f =0 K = 6.3. This gives the 1981 cost as 4.4 X 10 . The 1991 battery-Hmits investment can be obtained, by updating with the CE Plant Cost Index, as 5.3 x 10 . ... 

Because each effect of an evaporator produces almost as much vapor as the amount it condenses, the total evaporation accompHshed per unit of prime steam, or steam economy, iacreases ia almost direct proportioa to the number of effects used. The total heat load is also spHt up betweea the effects so that each effect has a much lower heat duty than a single effect for the same total evaporation load. However, the total available AT is also spHt up similarly so that each effect of a multiple effect requites about as much heating surface as a single effect operating over the same total temperature difference. Thus ia selecting the number of effects to use ia any iastallatioa, steam cost savings and capital cost of effects have to be balanced. Even before... 

Sindlady, heating surface area needs are not direcdy proportional to the number of effects used. For some types of evaporator, heat-transfer coefficients decline with temperature difference as effects are added the surface needed in each effect increases. On the other hand, heat-transfer coefficients increase with temperature level. In a single effect, all evaporation takes place at a temperature near that of the heat sink, whereas in a double effect half the evaporation takes place at this temperature and the other half at a higher temperature, thereby improving the mean evaporating temperature. Other factors to be considered are the BPR, which is additive in a multiple-effect evaporator and therefore reduces the net AT available for heat transfer as the number of effects is increased, and the reduced demand for steam and cooling water and hence the capital costs of these auxiUaries as the number of effects is increased. 

---