Being successful

To illustrate calculations for a binary system containing a supercritical, condensable component. Figure 12 shows isobaric equilibria for ethane-n-heptane. Using the virial equation for vapor-phase fugacity coefficients, and the UNIQUAC equation for liquid-phase activity coefficients, calculated results give an excellent representation of the data of Kay (1938). In this case,the total pressure is not large and therefore, the mixture is at all times remote from critical conditions. For this binary system, the particular method of calculation used here would not be successful at appreciably higher pressures. 

Radiographic inspection is performed to reach a decision about the acceptability of the component or product being tested. Before any evaluation can be made, the interpreter must be certain that the images are satisfactory. In addition, the interpreter must have a solid understanding of the following in order to be successful with the interpretation of the radiographic film for welding quality. 

Techniques such as NMR spectroscopy (section B1.12) and IR spectroscopy (section B1.2) are useful in such experiments. Furtlieniiore, tlieory (section B3.1) has proceeded to tlie point of being successful in predicting some simple catalytic cycles. 

Mean-centering, as is shown by experience, can be successfully employed in combination with another data pre-processing technique, namely scaling, which is discussed later. 

The chloroplatinates prepared as above are sufficiently pure for direct analysis without recrystallisation. The chloroplatinates of the amines are usually freely soluble in hot water, but recrystallisation (when required) should not be attempted until the process has been found to be successful with a small test-portion of the chloroplatinate. The chloroplatinates of many primary and secondary amines decompose in hot water, the amine being oxidised, and the chloroplatinate reduced to the metal some amines furthermore co-ordinate readily with the metal when the chloroplatinate is boiled with water and a mixed product is obtained on cooling. 

Noth. The above method can be successfully applied only to dilute solutions of formaldehyde which are free in particular from other alfphatic aldehydes, since the latter, if present, would undergo a similar oxidation. Formaldehyde, if mixed with other aldehydes, should be estimated by quantitative addition of potassium cyanide for details, see advanced text-books of quantitative organic analysis. 

When either of the reactants is sensitive to mineral acids, the esterification can often be successfully accomplished with the aid of a cation exchange resin (hydrogen form) in the presence of benzene. Zeo-Karb 225/H, a unifunctional sulphonated polystyrene resin in the hydrogen form, may be used. Thus good yields of isopropyl lactate may be obtained ... 

Note 2. A large number of experimental examples are given in Ref. 108. In some cases methyl sulfonates can be successfully applied when the use of the sulfinic esters leads to mixtures of 1,1- and 1,3-substitution products. 

The problem of the synthesis of highly substituted olefins from ketones according to this principle was solved by D.H.R. Barton. The ketones are first connected to azines by hydrazine and secondly treated with hydrogen sulfide to yield 1,3,4-thiadiazolidines. In this heterocycle the substituents of the prospective olefin are too far from each other to produce problems. Mild oxidation of the hydrazine nitrogens produces d -l,3,4-thiadiazolines. The decisive step of carbon-carbon bond formation is achieved in a thermal reaction a nitrogen molecule is cleaved off and the biradical formed recombines immediately since its two reactive centers are hold together by the sulfur atom. The thiirane (episulfide) can be finally desulfurized by phosphines or phosphites, and the desired olefin is formed. With very large substituents the 1,3,4-thiadiazolidines do not form with hydrazine. In such cases, however, direct thiadiazoline formation from thiones and diazo compounds is often possible, or a thermal reaction between alkylideneazinophosphoranes and thiones may be successful (D.H.R. Barton, 1972, 1974, 1975). 

Bromination of 2-dialkylaminothiazoles has been reported to be successful by one author (415) and to fail by others (375. 385). If the mechanism of direct electrophilic substitution is accepted for these compounds, it is difficult to understand why alkyl substitution on such a remote position as exocyclic nitrogen may inhibit this reaction in the C-5 position. 

Preparation of Arylcarboxylic Acids and Derivatives. The general Friedel-Crafts acylation principle can be successfully appHed to the preparation of aromatic carboxyUc acids. Carbonyl haUdes (phosgene, carbonyl chloride fluoride, or carbonyl fluoride) [353-50-4] are diacyl haUdes of carbonic acid. Phosgene [75-44-5] or oxalyl chloride [79-37-8] react with aromatic hydrocarbons to give aroyl chlorides that yield acids on hydrolysis (133) ... 

Waste aqueous metalworking fluids may be successfully treated by conventional means for removal of tramp oil, surfactants, and other chemical agents to provide suitable effluent water quaUty (78). 

In order to be successful any maintenance department needs strong internal customer—suppher partnerships. Such partnerships require opportunity for mutual benefits, predictable performance by each partner, and communication across links. 

Series Systems. The series configuration is the most commonly encountered in practice. In a series system, all subsystems must operate successfully for the system to be successful. The rehabihty block diagram is given in Figure 6. 

Nuclear utiUties have sharply reduced the volume of low level radioactive waste over the years. In addition to treating wastes, utiUties avoid contamination of bulk material by limiting the contact with radioactive materials. Decontamination of used equipment and materials is also carried out. For example, lead used for shielding can be successfully decontaminated and recycled using an abrasive mixture of low pressure air, water, and alumina. 

Adhesives. High concentration (>10%) solutions of poly(ethylene oxide) exhibit wet tack properties that are used in several adhesive appHcations. The tackiness disappears when the polymer dries and this property can be successfully utilized in appHcations that require adhesion only in moist conditions. PEO is also known to form solution complexes with several phenoHc and phenoxy resins. Solution blends of PEO and phenoxy resins are known to exhibit synergistic effects, leading to high adhesion strength on aluminum surfaces. Adhesive formulations are available from the manufacturers. 

---