ATOMIC emission spectroscopy 1 Technique

The emerging analytical technique of laser-induced breakdown spectroscopy (LIBS) is a simple atomic emission spectroscopy technique that has the potential for real-time man-portable chemical analysis in the field. Because LIBS is simultaneously sensitive to all elements, a single laser shot can be used to record the broadband emission spectra, which provides a chemical fingerprint of a material. 

Laser-induced breakdown spectroscopy (LIBS) is a relatively new atomic emission spectroscopy technique that uses a pulsed laser as the excitation sonrce. LIBS is also referred to as laser spark spectroscopy (LASS) and laser-induced plasma spectroscopy, with the unfortunate acronym of LIPS. The technique was developed in the early 1960s, after the invention of the laser, but the high cost and large size of lasers and spectrometers made this a specialized research tool until the 1990s. The early development of LIBS is covered in the reference by Myers et al. Recent advances... 

ICP/AES. inductively coupled plasma and atomic-emission spectroscopy used as a combined technique... 

The use of a plasma as an atomisation source for emission spectroscopy has been developed largely in the last 20 years. As a result, the scope of atomic emission spectroscopy has been considerably enhanced by the application of plasma techniques. 

The most appropriate experimental procedure is to treat the metal in UHV, controlling the state of the surface with spectroscopic techniques (low-energy electron diffraction, LEED atomic emission spectroscopy, AES), followed by rapid and protected transfer into the electrochemical cell. This assemblage is definitely appropriate for comparing UHV and electrochemical experiments. However, the effect of the contact with the solution must always be checked, possibly with a backward transfer. These aspects are discussed in further detail for specific metals later on. 

Atomic absorption spectroscopy and atomic emission spectroscopy are analytical techniques in which the wavelength of radiation absorbed... 

When the problem has been defined and needed background information has been studied, it is time to consider which analytical methods will provide the data you need to solve the problem. In selecting techniques, you can refer back to the other chapters in this book. For example, if you want to measure the three heavy metals (Co, Fe, and Ni) that were suspect in the Bulging Drum Problem, you might immediately think of atomic absorption or inductively coupled plasma atomic emission spectroscopies and reread Chapter 8 of this book. How would you choose between them Which would be more accurate More precise Does your lab have both instruments Are they both in working order What if you have neither of them What sample preparation would be needed ... 

NMR) [24], and Fourier transform-infrared (FT-IR) spectroscopy [25] are commonly applied methods. Analysis using mass spectrometric (MS) techniques has been achieved with gas chromatography-mass spectrometry (GC-MS), with chemical ionisation (Cl) often more informative than conventional electron impact (El) ionisation [26]. For the qualitative and quantitative characterisation of silicone polyether copolymers in particular, SEC, NMR, and FT-IR have also been demonstrated as useful and informative methods [22] and the application of high-temperature GC and inductively coupled plasma-atomic emission spectroscopy (ICP-AES) is also described [5]. 

Measurements of the intensity and wavelength of radiation that is either absorbed or emitted provide the basis for sensitive methods of detection and quantitation. Absorption spectroscopy is most frequently used in the quantitation of molecules but is also an important technique in the quantitation of some atoms. Emission spectroscopy covers several techniques that involve the emission of radiation by either atoms or molecules but vary in the manner in which the emission is induced. Photometry is the measurement of the intensity of radiation and is probably the most commonly used technique in biochemistry. In order to use photometric instruments correctly and to be able to develop and modify spectroscopic techniques it is necessary to understand the principles of the interaction of radiation with matter. 

In reference 190, the authors describe the spectroscopic and X-ray crystallographic techniques they used to determine the pMMO structure. First, EPR and EX AFS experiments indicated a mononuclear, type 2 Cu(II) center hgated by histidine residues and a copper-containing cluster characterized by a 2.57 A Cu-Cu interaction. A functional iron center was also indicated by Inductively Coupled Plasma-Atomic Emission Spectroscopy (ICP-AES). ICP-AES uses inductively coupled plasma to produce excited atoms that emit electromagnetic radiation at a wavelength characteristic of a particular element. The intensity of this emission is indicative of the concentration of the element (iron in this case) within the sample. 

Atomic emission spectroscopy is one of the oldest instrumental techniques used for chemical analysis. It is used to study the transitions between electronic energy levels in atoms or ions. These energy differences are usually in the visible region (400-700 nm) of the electromagnetic spectrum, but if the energy difference is larger, then the transitions may lie in the ultraviolet region. 

Chapters 7 and 8 describe two major techniques for the monitoring of trace elements in environmental samples atomic absorption (AA) and inductively coupled plasma-atomic emission spectroscopy (ICP). AA is most ideally suited for analyses where a limited number of trace metal concentrations are needed with high accuracy and precision. ICP has the advantage of multielement analysis with high speed. 

Iron metal can be analyzed by x-ray spectroscopy, flame- and furnace atomic absorption, and ICP atomic emission spectroscopy at trace concentration levels. Other instrumental techniques include ICP-mass spectrometry for extreme low detection level and neutron activation analysis. 

Figure 1.2 shows the basic instrumentation necessary for each technique. At this stage, we shall define the component where the atoms are produced and viewed as the atom cell. Much of what follows will explain what we mean by this term. In atomic emission spectroscopy, the atoms are excited in the atom cell also, but for atomic absorption and atomic fluorescence spectroscopy, an external light source is used to excite the ground-state atoms. In atomic absorption spectroscopy, the source is viewed directly and the attenuation of radiation measured. In atomic fluorescence spectroscopy, the source is not viewed directly, but the re-emittance of radiation is measured. 

M. L. Griffiths, D. Svozil, P. J. Worsfold, S. Denham and E. H. Evans, Comparison of traditional and multivariate calibration techniques applied to complex matrices using inductively coupled plasma atomic emission spectroscopy, J. Anal. At. Spectrom., 15, 2000, 967-972. 

Atomic emission spectroscopy can be employed, generally with an inductively coupled plasma for thermal excitation. The sample is introduced into the plasma as a mist of ultrafine droplets, and the monochromator and detector are set to measure the intensity of an atomic emission line characteristic of the element. This technique is powerful, general, sensitive, linear, and able to measure over 70 elements, and, as a result, is widely used. Response is typically linear over four orders of magnitude in concentration with relative standard deviations of 1 to 3%. In low-salt aqueous solutions, detection limits range from 10 to 1000 nanomolar without preconcentration. Significant problems with saline samples remain, but use of Babington nebulizers alleviates these problems somewhat. 

Trace levels (10 to 10 g/g of sample) of silver can be accurately determined in biological samples by several different analytical techniques, provided that the analyst is well acquainted with the specific problems associated with the chosen method. These methods include high frequency plasma torch-atomic emission spectroscopy (HFP-AES), neutron activation analysis (NAA), graphite furnace (flameless) atomic absorption spectroscopy (GFAAS), flame atomic absorption spectroscopy (FAAS), and micro-cup atomic absorption spectroscopy (MCAAS). 

A number of analytical methods were developed for determination of elemental mercury. The methods are reviewed in Refs. [1-4]. They include traditional analytical techniques, such as atomic adsorption spectroscopy (AAS), atomic fluorescence spectroscopy (AFS), and atomic emission spectroscopy (AES). The AAS is based on measurements of optical adsorption at 253.7 or 184.9 nm. Typical value of the detection limit without pre-concentration step is over 1 pg/l. The AEF is much more sensitive and allows one to detect less than 0.1ng/l of mercury... 

The ion atmosphere of nucleic acids directly affects measured biochemical and biophysical properties. However, study of the ion atmosphere is difficult due to its diffuse and dynamic nature. Standard techniques available have significant limitations in sensitivity, specificity, and directness of the assays. Buffer exchange-atomic emission spectroscopy (BE-AES) was developed to overcome many of the limitations of previously available techniques. This technique can provide a complete accounting of all ions constituting the ionic atmosphere of a nucleic acid at thermodynamic equilibrium. Although initially developed for the study of the ion atmosphere of nucleic acids, BE-AES has also been applied to study site-bound ions in RNA and protein. 

To overcome the limitations of other techniques, buffer exchange-atomic emission spectroscopy (BE-AES) was created (Bai et al, 2007). Measurements of the ion atmosphere done with BE-AES provide a rigorous thermodynamic measure of the number of ions associated with a nucleic acid. BE-AES is sensitive to a wide number of elements and has proven to... 

---