Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Anionic chain polymerization temperature effect

Polar Vinyl Monomers The anionic polymerization of polar vinyl monomers is often complicated by side reactions of the monomer with both anionic initiators and growing carbanionic chain ends, as well as chain termination and chain transfer reactions. However, synthesis of polymers with well-defined structures can be effected under carefully controlled conditions. The anionic polymerizations of alkyl methacrylates and 2-vinylpyridine exhibit the characteristics of living polymerizations under carefully controlled reaction conditions and low polymerization temperatures to minimize or eliminate chain termination and transfer reactions [118, 119]. Proper choice of initiator for anionic polymerization of polar vinyl monomers is of critical importance to obtain polymers with predictable, well-defined structures. As an example of an initiator that is too reactive, the reaction of methyl methacrylate (MMA)... [Pg.139]

Effects of solvent polarity, counter-anion nucleophilidty, temperature, and monomer concentration on the carbenium ion polymerization chemistry have been extensively studied29,36 38,49. Based on previous knowledge26"29 Me3Al was chosen because with this coinitiator undesired chain transfer to monomer processes are absent. Preliminary experiments showed that Et3Al coinitiator did not yield PaMeSt, possibly because the nuc-leophilicity of the counter-anion Et3AlQe is too high and thus termination by hydrida-tion is faster than propagation36. ... [Pg.31]

Another interesting chiral chain end effect is exhibited by the helical polymer block co-polymer, poly(l,l-dimethyl-2,2-di-/z-hexylsilylene)- -poly(triphenylmethyl methacrylate), reported by Sanji and Sakurai (see Scheme 7) and prepared by the anionic polymerization of a masked disilene.333 The helical poly(triphenylmethyl methacrylate) block (PTrMA) is reported to induce a PSS of the same sign in the poly(di- -propylsilylene) block in THF below — 20 °C, and also in the solid state, by helicity transfer, as evidenced by the positive Cotton effect at 340 nm, coincident with a fairly narrow polysilane backbone UV absorption characteristic of an all-transoid-conformation. This phenomenon was termed helical programming. Above 20°C, the polysilane block loses its optical activity and the UV absorption shifts to 310 nm in a reversible, temperature-dependent effect, due to the disordering of the chain, as shown in Figure 45. [Pg.622]

The stereoselective polymerization of various acrylates and methacrylates has been studied using initiators such as atkyllithium [Bywater, 1989 Pasquon et al., 1989 Quirk, 1995, 2002]. Table 8-12 illustrates the effects of counterion, solvent, and temperature on the stereochemistry of the anionic polymerization of methyl methacrylate (MMA). In polar solvents (pyridine and THF versus toluene), the counterion is removed from the vicinity of the propagating center and does not exert an influence on entry of the next monomer unit. The tendency is toward syndiotactic placement via chain end control. The extent of syndiotacticity... [Pg.699]

The solution thus consists of different particles denoted as contact ion pairs, solvent-separated ion pairs and free ions. The fraction of the individual particles depends on the type of salt, type of solvent, polymerization system, temperature, and salt concentration. The catalytic effect of these particles may be very different as is evident in anionic polymerization of vinyl monomers. For instance, free polystyryl anion is 800times more reactive than its ion pair with the sodium counterion 60 . From this fact it follows that, although the portion of free ions is small in the reaction system, they may play an important role. On the other hand, anionic polymerization and copolymerization of heterocycles proceeds mostly via ion pairs. This is due to a strong localization of the negative charge on the chain-end heteroatom which strongly stabilizes the ion pair itself62. Ionic dissociation constants and ion contributions to the reaction kinetics are usually low. This means that for heterocycles the difference between the catalytic effect of ion pairs and free ions is much weaker than for the polymerization of unsaturated compounds. This is well documented by the copolymerization of anhydrides with epoxides where the substi-... [Pg.103]

Catalysts of the Ziegler type have been used widely in the anionic polymerization of 1-olefins, diolefins, and a few polar monomers which can proceed by an anionic mechanism. Polar monomers normally deactivate the system and cannot be copolymerized with olefins. However, it has been found that the living chains from an anionic polymerization can be converted to free radicals in the presence of peroxides to form block polymers with vinyl and acrylic monomers. Vinylpyridines, acrylic esters, acrylonitrile, and styrene are converted to block polymers in good yield. Binary and ternary mixtures of 4-vinylpyridine, acrylonitrile, and styrene, are particularly effective. Peroxides are effective at temperatures well below those normally required for free radical polymerizations. A tentative mechanism for the reaction is given. [Pg.285]

Monomer II is also a polymerizable IL composed of quatemized imidazoliimi salt, as shown in Figure 29.1. This monomer is liquid at room temperature and shows a Tg only at —70°C. Its high ionic conductivity of about 10 S cm at room temperature reflects a low Tg. Although the ionic conductivity of this monomer decreased after polymerization as in the case of monomer I, it was considerably improved by the addition of a small amount of LiTFSI. Figure 29.3 shows the effect of LiTFSI concentration on the ionic conductivity and lithium transference number ( Li ) for polymer II. The bulk ionic conductivity of polymer II was 10 S cm at 50°C. When LiTFSI was added to polymer 11, the ionic conductivity increased up to 10 S cm After that, the ionic conductivity of polymer II decreased gradually with the increasing LiTFSI concentration. On the other hand, when the LiTFSI concentration was 100 mol%, the of this system exceeded 0.5. Because of the fixed imidazolium cations on the polymer chain, mobile anion species exist more than cation species in the polymer matrix at this concentration. Since the TFSI anions form the IL domain with the imidazolium cation, the anion can supply a successive ion conduction path for the lithium caiton. Such behavior is not observed in monomeric IL systems, and is understood to be due to the concentrated charge domains created by the polymerization. [Pg.349]

The difference in ionic conductivity can be attributed to the difference in freedom of the imidazoUum cation. This effect has already been confirmed empirically in our laboratory [11, 12]. For a simple system such as l-ethyl-3-vinylimidazolium TFSl, the ionic conductivity decreased by about four orders upon polymerization. The ionic conductivity of IL polymer brushes having PEO or hydrocarbon chains as spacers between the vinyl group and imidazolium salt are almost the same before and after polymerization. In spite of their rubberlike physical properties, IL polymer brushes had excellent ionic conductivity, around 10 " Scm , at room temperature. Details of the IL polymer brushes are given in Chapter 31. The ionic conductivity of P3 and P4, in which the imidazolium cation is fixed to the main chain, was very low even after salts were added to the matrix. P5 and P6 having the counter anion on the main chain displayed an ionic conductivity fom orders higher than P3 or P4 (about 10 S cm at 50°C). The distance between the vinyl polymer and the imidazolium cation is important for the high ionic conductivity in IL polymers. [Pg.360]

Anionic polymerization, however, can be used to produce high molecular weight narrow distribution polystyrene. If all the chains are initiated at the same time and the temperature is kept low to minimize chain transfer, molecular weight distributions very close to monodisperse can be produced. The commercial uses of these polymers seem to be limited to instrument calibrations and laboratory studies of the effects of molecular weight on rheology and physical properties. However, anionic polymerization as a potential commercial method for producing polystyrene has been extensively studied by Dow and others. The potential for high polymerization rates, complete conversion of... [Pg.51]

Under suitable conditions, anionic polymerization is faster than free-radical polymerization and so can be conducted at lower temperatures. The main reasons are fast initiation by an ionic reaction and absence of an effective termination mechanism. However, the sensitivity to impurities is much greater and choice and control of reaction conditions are more delicate. Water, oxygen, carbon dioxide, and other substances able to react with carbanion chain carriers must be strictly excluded. [Pg.325]

The active site in chain-growth polymerizations can be an ion instead of a free-radical. Ionic reactions are much more sensitive than free-radical processes to the effects of solvent, temperature, and adventitious impurities. Successful ionic polymerizations must be carried out much more carefully than normal free-radical syntheses. Consequently, a given polymeric structure will ordinarily not be produced by ionic initiation if a satisfactory product can be made by less expensive free-radical processes. Styrene polymerization can be initiated with free radicals or appropriate anions or cations. Commercial atactic styrene polymers are, however, all almost free-radical products. Particular anionic processes are used to make research-grade polystyrenes with exceptionally narrow molecular weight distributions and the syndiotactic polymer is produced by metallocene catalysis. Cationic polymerization of styrene is not a commercial process. [Pg.301]


See other pages where Anionic chain polymerization temperature effect is mentioned: [Pg.10]    [Pg.116]    [Pg.372]    [Pg.22]    [Pg.9]    [Pg.104]    [Pg.209]    [Pg.333]    [Pg.236]    [Pg.437]    [Pg.45]    [Pg.880]    [Pg.68]    [Pg.106]    [Pg.72]    [Pg.163]    [Pg.432]    [Pg.15]    [Pg.1054]    [Pg.98]    [Pg.157]    [Pg.197]    [Pg.174]    [Pg.80]    [Pg.31]    [Pg.218]    [Pg.562]    [Pg.177]    [Pg.221]    [Pg.380]    [Pg.783]    [Pg.44]    [Pg.27]    [Pg.54]    [Pg.88]    [Pg.30]    [Pg.570]    [Pg.340]    [Pg.332]   
See also in sourсe #XX -- [ Pg.429 , Pg.433 ]

See also in sourсe #XX -- [ Pg.429 , Pg.433 ]




SEARCH



Anion effects

Anionic chain polymerization

Anionic polymerization temperature

Anions anion effect

Chain effect

Effective chain

Polymerization effect

Polymerization temperature

Polymerization temperature effect

© 2024 chempedia.info