Anionic polymerization temperature

In the case of anionic polymerization (with 2-isoprOpenylthiazole) there is a chain-monomer equilibrium. Furthermore, lowering the temperature of polymerization increases the conversion of monomer to polymer (314). 

A brief review has appeared covering the use of metal-free initiators in living anionic polymerizations of acrylates and a comparison with Du Font s group-transfer polymerization method (149). Tetrabutylammonium thiolates mn room temperature polymerizations to quantitative conversions yielding polymers of narrow molecular weight distributions in dipolar aprotic solvents. Block copolymers are accessible through sequential monomer additions (149—151) and interfacial polymerizations (152,153). 

Cyanoacrylate adhesives (Super-Glues) are materials which rapidly polymerize at room temperature. The standard monomer for a cyanoacrylate adhesive is ethyl 2-cyanoacrylate [7085-85-0], which readily undergoes anionic polymerization. Very rapid cure of these materials has made them widely used in the electronics industry for speaker magnet mounting, as weU as for wire tacking and other apphcations requiring rapid assembly. Anionic polymerization of a cyanoacrylate adhesive is normally initiated by water. Therefore, atmospheric humidity or the surface moisture content must be at a certain level for polymerization to take place. These adhesives are not cross-linked as are the surface-activated acryhcs. Rather, the cyanoacrylate material is a thermoplastic, and thus, the adhesives typically have poor temperature resistance. 

The vast majority of commercial apphcations of methacryhc acid and its esters stem from their facile free-radical polymerizabiUty (see Initiators, FREE-RADICAl). Solution, suspension, emulsion, and bulk polymerizations have been used to advantage. Although of much less commercial importance, anionic polymerizations of methacrylates have also been extensively studied. Strictiy anhydrous reaction conditions at low temperatures are required to yield high molecular weight polymers in anionic polymerization. Side reactions of the propagating anion at the ester carbonyl are difficult to avoid and lead to polymer branching and inactivation (38—44). 

The anionic polymerization of methacrylates using a silyl ketene acetal initiator has been termed group-transfer polymerization (GTP). First reported by Du Pont researchers in 1983 (100), group-transfer polymerization allows the control of methacrylate molecular stmcture typical of living polymers, but can be conveniendy mn at room temperature and above. The use of GTP to prepare block polymers, comb-graft polymers, loop polymers, star polymers, and functional polymers has been reported (100,101). 

Anionic Polymerization of Cyclic Siloxanes. The anionic polymerization of cyclosiloxanes can be performed in the presence of a wide variety of strong bases such as hydroxides, alcoholates, or silanolates of alkaH metals (59,68). Commercially, the most important catalyst is potassium silanolate. The activity of the alkaH metal hydroxides increases in the foUowing sequence LiOH < NaOH < KOH < CsOH, which is also the order in which the degree of ionization of thein hydroxides increases (90). Another important class of catalysts is tetraalkyl ammonium, phosphonium hydroxides, and silanolates (91—93). These catalysts undergo thermal degradation when the polymer is heated above the temperature requited (typically >150°C) to decompose the catalyst, giving volatile products and the neutral, thermally stable polymer. 

Anionic polymerization offers fast polymerization rates on account of the long life-time of polystyryl carbanions. Early studies have focused on this attribute, most of which were conducted at short reactor residence times (< 1 h), at relatively low temperatures (10—50°C), and in low chain-transfer solvents (typically benzene) to ensure that premature termination did not take place. Also, relatively low degrees of polymerization (DP) were typically studied. Continuous commercial free-radical solution polymerization processes to make PS, on the other hand, operate at relatively high temperatures (>100° C), at long residence times (>1.5 h), utilize a chain-transfer solvent (ethylbenzene), and produce polymer in the range of 1000—1500 DP. 

Thermoplastic Elastomers. These represent a whole class of synthetic elastomers, developed siace the 1960s, that ate permanently and reversibly thermoplastic, but behave as cross-linked networks at ambient temperature. One of the first was the triblock copolymer of the polystyrene—polybutadiene—polystyrene type (SheU s Kraton) prepared by anionic polymerization with organoHthium initiator. The stmcture and morphology is shown schematically in Figure 3. The incompatibiHty of the polystyrene and polybutadiene blocks leads to a dispersion of the spherical polystyrene domains (ca 20—30 nm) in the mbbery matrix of polybutadiene. Since each polybutadiene chain is anchored at both ends to a polystyrene domain, a network results. However, at elevated temperatures where the polystyrene softens, the elastomer can be molded like any thermoplastic, yet behaves much like a vulcanized mbber on cooling (see Elastomers, synthetic-thermoplastic elastomers). 

Commercial chloroprene polymerization is most often carried out in aqueous emulsion using an anionic soap system. This technique provides a relatively concentrated polymerization mass having low viscosity and good transfer of the heat of polymerization. A water-soluble redox catalyst is normally used to provide high reaction rate at relatively low polymerization temperatures. 

In general, the activation energies for both cationic and anionic polymerization are small. For this reason, low-temperature conditions are normally used to reduce side reactions. Low temperatures also minimize chain transfer reactions. These reactions produce low-molecular weight polymers by disproportionation of the propagating polymer ... 

Chain growth occurs through a nucleophilic attack of the carbanion on the monomer. As in cationic polymerizations, lower temperatures favor anionic polymerizations by minimizing branching due to chain transfer reactions. 

In anionic polymerization, as in carbonium ion polymerization, termination does not involve bimolecular reaction between two growing chains. Neither can recombination of ions lead to termination, since a carbon-metal bond is highly polar, in the case of alkali metals frequently completely ionized, and in every case very reactive. The termination step leading to the formation of a terminal C=C double bond is not too probable. This reaction involves the formation of a metal hydride, and this does not contribute greatly to the driving force. Consequently, such a termination is observed at higher temperatures only and it is probably more common in coordination polymerization where the metals involved are less electropositive. 

Effects of solvent polarity, counter-anion nucleophilidty, temperature, and monomer concentration on the carbenium ion polymerization chemistry have been extensively studied29,36 38,49. Based on previous knowledge26"29 Me3Al was chosen because with this coinitiator undesired chain transfer to monomer processes are absent. Preliminary experiments showed that Et3Al coinitiator did not yield PaMeSt, possibly because the nuc-leophilicity of the counter-anion Et3AlQe is too high and thus termination by hydrida-tion is faster than propagation36. ... 

The anionic polymerization of caprolactam is rapid and can be carried out below die melting temperature of the PA. Care should be taken to work under anhydrous conditions. 

Two-shot techniques for acyclic diene metathesis, 435-445 for polyamides, 149-164 for polyimides, 287-300 for polyurethanes, 241-246 for transition metal coupling, 483-490 Anionic deactivation, 360 Anionic polymerization, 149, 174 of lactam, 177-178 Apolar solvents, 90 Aprotic polar solvents, 185, 338 Aprotic solvents, low-temperature condensation in, 302 Aqueous coating formulations, 235 Aqueous polyoxymethylene glycol, depolymerization of, 377 Aqueous systems, 206 Ardel, 20, 22... 

Some of the results of bulk polymerization of 61 by using different anionic catalysts are summarized in Table 858 It was easily polymerized in the presence of alkali metal compounds above 60 °C. The polymerization at 150 °C was too fast to be controlled. The yield and the viscosity number, i gp/c, of the resulting polyamide increased with the reaction time. The initial rate of the polymerization became higher with the size of the countercation, in analogy to the case of anionic polymerization of e-caprolactam59. The rate increased also with raising temperature as shown in Fig. 658. ... 

The anionic polymerization of 61 catalysed by potassium pyrrolidonate is characterized by a rapid conversion in THF and DMSO, even at or below room temperatures, as indicated in Table 9s8. ... 

A pilot scale plant, incorporating a three litre continuous stirred tank reactor, was used for an investigation into the n-butyl lithium initiated, anionic polymerization of butadiene in n-hexane solvent. The rig was capable of being operated at elevated temperatures and pressures, comparable with industrial operating conditions. 

The 1,4 units constitute somewhat less than half of the total in polymerized dienes prepared by anionic polymerization at moderate temperature. Their proportion increases with the polymerization temperature. 

The anionic polymerization of the MM block was initiated with fluorenyllithium (14) in THF at -78°C. After several hours, t-butyl methacrylate was introduced, and the polymerization was allowed to slowly rise to room temperature. The reaction was quenched with a few drops of methanol and precipitated from ligroin. The dried polymer was analyzed by NMR, IR, and GPC. The 1H NMR spectrum displays signals at 0.85, 1.02, and 1.13 (shoulder) ppm for the... 

Table 2. Anionic Polymerization of Masked Disilene 7 initiated by Silyl Anions in the Presence of Cryptand in Benzene at Room Temperature...

---