Ammonium stabilization

An alternative approach to stabilize nanoparticles is to use polyoxoanions (see Scheme 9.5). Finke and coworkers described polyoxoanion- and ammonium-stabilized rhodium zerovalent nanoclusters for the hydrogenation of classical benzene compounds [95, 108]. This organometallic approach allows reproducible preparation of stable nanoparticles starting from a well-defined complex in terms of composition and structure (see Section 9.3.5). 

For example, alkyl ammonium-stabilized metal nanoparticles were generated by electrochemical process. A target bulk metal sheet is settled as an anode in an electrochemical cell as shown in Figure 9.1.1. Metal cations are generated at the anode and move to the cathode. Metal ions are reduced there by electrons generated from the cathode to form zero-valence metal atoms. In many cases, the zero-valence metal atoms are deposited onto the cathode metal sheet (usually platinum) or precipi-... 

Since particle charge in these latexes is not pH dependent, the mechanism outlined above for the conventional electrocoating systems cannot apply. It was clear from the start that the difference in the behavior of sulfonium and quaternary ammonium stabilized latexes is related to the greater reactivity of the sulfonium ion. Though stable in dilute aqueous solutions, sulfonium ions might be expected to undergo rapid decomposition under the conditions obtained at the cathode surface while current is flowing. However, the specific reactions involved were not known. 

Bismuth cerium molybdates were prepared by coprecipitation using aqueous solutions of (NH ) Mo 02, (NH,)2Ce(N0 ), and Bi(NO ) 5H2O. The catalysts were supported on oiO (20% by weight) using an ammonium stabilized silica sol. Samples for diffraction analysis were unsupported. Samples were calcined in air at 290 and 425°C for three hours each followed by 16 hours at 500, 550, or 600 C. X-ray powder patterns were obtained using a Rlgaku D/Max-IIA X-ray diffractometer using Cu K radiation. 

Figure 13. Sodium- and ammonium-stabilized and aluminum-modified surfaces of colloidal silicas.

Reactants used were reagent grade lithium carbonate, lithium hydroxide, and sodium hydroxide, aluminum hydroxide (Grades C-31, C-730, Hydral 705, and 710 ALCOA), precipitated silicic acid (Fisher Scientific), and ammonium-stabilized aqueous colloidal silica sol (Ludox "AS, DuPont). Other reactants, which were used and found unsatisfactory to produce mordenite as a phase under the experimental conditions investigated, were fumed silica, silica gel, silica-alumina gels, diatomite, and sodium aluminate. 

Ammonium stabilized Average particle size 25 nm Size range 12—50 nm Solids 30% pH 9-11... 

Fig. 6.14 (A)[54] TEM images of (a) y-CD-capped gold nanopaiticles tind (b) Cgo-induced aggregation. (c) Schematic illustration of the structure of fullerene-induced network of y-CD-capped gold nanoparticles in aqueous dispersion. (B)[75] (a) Schematic illustration of the mediation-template strategy for quatemeiry ammonium-stabilized gold nanopaiticles and a mediettor (2) (b-d) TEM images of the 2-mediated nanoparticle assemblies prepared by various conditions...

Types of Counterions. In most patents relating to colloidal silica the stabilizing bases include the hydroxides of potassium, lithium, sodium, and ammonium. The sols are most commonly stabilized with sodium hydroxide, and then if other bases are to be substituted, the sols are deionized in mixed anion-cation resin beds and restabilized with the desired base. The ammonium-stabilized sols are employed where pure silica is desired. The lower amines can be used in place of ammonia, but are generally avoided because of odor (203). 

The 2-imino-4-thiazolines may be used as ultraviolet-light stabilizers of polyolefin compositions (1026). 2-Aminothiazole improves adhesive properties of wood to wood glue (271). Cbmpound 428 exhibits antioxidant properties (Scheme 242) (1027). Ammonium N-(2-thiazolyl)dithio-carbamate (429) is a bactericide and fungicide used in industrial products such as lumber, paint, plastics, and textiles (1037). Compound 430 is reported (1038) to form an excellent volume of foam coating in aluminum pans when ignited with propane. 

In addition to hydrogen bonding between the two polynucleotide chains the double helical arrangement is stabilized by having its negatively charged phosphate groups on the outside where they are m contact with water and various cations Na" Mg and ammonium ions for example Attractive van der Waals forces between the... 

Acetonitrile also is used as a catalyst and as an ingredient in transition-metal complex catalysts (35,36). There are many uses for it in the photographic industry and for the extraction and refining of copper and by-product ammonium sulfate (37—39). It also is used for dyeing textiles and in coating compositions (40,41). It is an effective stabilizer for chlorinated solvents, particularly in the presence of aluminum, and it has some appflcation in... 

Polymer-based rocket propellants are generally referred to as composite propellants, and often identified by the elastomer used, eg, urethane propellants or carboxy- (CTPB) or hydroxy- (HTPB) terrninated polybutadiene propellants. The cross-linked polymers act as a viscoelastic matrix to provide mechanical strength, and as a fuel to react with the oxidizers present. Ammonium perchlorate and ammonium nitrate are the most common oxidizers used nitramines such as HMX or RDX may be added to react with the fuels and increase the impulse produced. Many other substances may be added including metallic fuels, plasticizers, stabilizers, catalysts, ballistic modifiers, and bonding agents. Typical components are Hsted in Table 1. 

Aqueous emulsion polymerization is carried out using a fluorinated emulsifier, a chain-transfer agent to control molecular weight, and dispersion stabilizers such as manganic acid salts and ammonium oxalate (13,14). 

Diketene is a flammable Hquid with a flash point of 33°C and an autoignition temperature of 275°C. It decomposes rapidly above 98°C with slow decomposition occurring even at RT. The vapors are denser than air (relative density 2.9, air air = 1). The explosive limits in air are 2—11.7 vol % (135). In case of fire, water mist, light and stabilized foam, as well as powder of the potassium or ammonium sulfate-type should be used. Do not use basic extinguisher powders and do not add water to a closed container. 

Ammonium chloride [12125-02-9], ammonium sulfate [7783-20-2], and diammonium phosphate [7708-28-0] have also been used for shale stabilization (102,103). Ammonium ions have essentially the same effect on shales as potassium ions but use of ammonium salts is often objectionable because of the alkaline nature of the mud. In the North Sea and northern Europe, where magnesium-bearing salt formations ate encountered, magnesium chloride [7786-30-3] is used, but in the United States it is used only on a small scale. 

Toluhydroquinone and methyl / fX butyUiydroquinone provide improved resin color retention 2,5-di-/-butyIhydroquinone also moderates the cure rate of the resin. Quaternary ammonium compounds, such as benzyl trimethyl ammonium hydroxide, are effective stabilizers in combination with hydroquinones and also produce beneficial improvements in color when promoted with cobalt octoate. Copper naphthenate is an active stabilizer at levels of 10 ppm at higher levels (150 ppm) it infiuences the cure rate. Tertiary butylcatechol (TBC) is a popular stabilizer used by fabricators to adjust room temperature gelation characteristics. 

Pyrotechnic mixtures may also contain additional components that are added to modify the bum rate, enhance the pyrotechnic effect, or serve as a binder to maintain the homogeneity of the blended mixture and provide mechanical strength when the composition is pressed or consoHdated into a tube or other container. These additional components may also function as oxidizers or fuels in the composition, and it can be anticipated that the heat output, bum rate, and ignition sensitivity may all be affected by the addition of another component to a pyrotechnic composition. An example of an additional component is the use of a catalyst, such as iron oxide, to enhance the decomposition rate of ammonium perchlorate. Diatomaceous earth or coarse sawdust may be used to slow up the bum rate of a composition, or magnesium carbonate (an acid neutralizer) may be added to help stabilize mixtures that contain an acid-sensitive component such as potassium chlorate. Binders include such materials as dextrin (partially hydrolyzed starch), various gums, and assorted polymers such as poly(vinyl alcohol), epoxies, and polyesters. Polybutadiene mbber binders are widely used as fuels and binders in the soHd propellant industry. The production of colored flames is enhanced by the presence of chlorine atoms in the pyrotechnic flame, so chlorine donors such as poly(vinyl chloride) or chlorinated mbber are often added to color-producing compositions, where they also serve as fuels. 

The most commonly used emulsifiers are sodium, potassium, or ammonium salts of oleic acid, stearic acid, or rosin acids, or disproportionate rosin acids, either singly or in mixture. An aLkylsulfate or aLkylarenesulfonate can also be used or be present as a stabilizer. A useful stabilizer of this class is the condensation product of formaldehyde with the sodium salt of P-naphthalenesulfonic acid. AH these primary emulsifiers and stabilizers are anionic and on adsorption they confer a negative charge to the polymer particles. Latices stabilized with cationic or nonionic surfactants have been developed for special apphcations. Despite the high concentration of emulsifiers in most synthetic latices, only a small proportion is present in the aqueous phase nearly all of it is adsorbed on the polymer particles. 

---