Active surfactant

Shampoos based on lauryl sulfates can range from 6—17% of the active surfactant. However, though they are effective cleansers, the alkyl sulfates tend to be defatting. In an effort to make these shampoos more mild, many shampoos are now based on blends of amphoterics and alkyl sulfates or the less irritating alkyl ether sulfates. 

SAMs are ordered molecular assembHes formed by the adsorption (qv) of an active surfactant on a soHd surface (Fig. 6). This simple process makes SAMs inherently manufacturable and thus technologically attractive for building supedattices and for surface engineering. The order in these two-dimensional systems is produced by a spontaneous chemical synthesis at the interface, as the system approaches equiHbrium. Although the area is not limited to long-chain molecules (112), SAMs of functionalized long-chain hydrocarbons are most frequently used as building blocks of supermolecular stmctures. 

Fluorocarbons with a hydrophilic functional group are very active surfactants [23]. Less than 1% of ionic or nonionic surfactants with perfluoroalkyl groups can reduce the surface tension of water from 72 to 15-20 dyne/cm, compared with 25-35dyne/cm for typical hydrocarbon surfactants [24] Perfluoroether surfactants are about as active as their perfluoroalkyl counterparts of similar chain length [25, 26], but fluorosurfactants with more polar alkyl end groups are considerably less active than their perfluoroalkyl analogues (Table 7)... 

FIG. 36 Synergistic mixture of alkane- (paraffin) sulfonates (PS) and fatty alcohol ether sulfates (FAES). Cleaning effect in miniplate test at 50°C, tap water (12° German hardness), 0.075 g of active surfactant mixture per liter. 

Alkanesulfonates are an important internal antistatic agent for polystyrene (PS) as well. If it is not possible to apply the pure active surfactant with the intended processing machine, the use of a master batch of alkanesulfonates and an appropriate polystyrene product is recommended. The addition of alkanesulfonates in amounts greater than 0.3 phr can cause hazing also in transparent PS articles. The antistatic effect of alkanesulfonates in PS is demonstrated in Fig. 41. 

Turbidity measurements were determined using the dipping probe colorimeter. The light frequency was 650 nm. Deionized water transmittance was set at 90. The surfactant test solutions were stirred ( — 3500 rpm) and maintained at 75°C. Active surfactant concentration was 0.1% wt. Solution volume was 100 cm1. A 26.5% CaCU (95,699 ppm CaJ+) solution was added via syringe in 0,10 ml increments to the lower portion of the surfactant solution. 

Tests were performed at 75°C using a University of Texas Model 500 spinning drop tensiometer. Active surfactant concentration in the aqueous phase prior to oil addition was 0.50% wt. The Kem River crude oil was from the Patricia Lease. The pH of the deionized water surfactant solutions was 8. The pH of the aqueous NaCl surfactant solutions was 9.5 unless otherwise noted. values represent the average deviation of two or three measurements at different times (0.75-1 h apart). D.I., deionized. 

Tests were performed at 75°C using a University of Texas Model 500 spinning drop tensiometer. Active surfactant concentration in the aqueous phase prior to addition of the oil phase was 0.5% wt. Interfacial tension values are the average of duplicate or triplicate determinations. 

Initial surfactant concentration was 0.50% wt in pH 8.5 solution. 50 g of test solution was placed over 100.0 g crushed Berea sandstone. The sample bottle was sealed and shaken continuously for 24 h at 75°C. The mixed indicator titration technique was used to determine active surfactant concentration before and after exposure of the test solution to crushed Berea sandstone. AS HAS, alkene.hydroxyalkanemonosulfonate ratio. D.I. water, deionized water. ND, not determined. 

Study performed at the National Institue of Petroleum and Energy Research. bRelative to active surfactant concentration. 

Self-assembled monolayers are formed spontaneously by the immersion of an appropriate substrate into a solution of active surfactant in an organic solvent. After the substrate is immersed for a time from minutes to hours, it is rinsed with ligroin, methanol, distilled water, and dried in a steam of nitrogen. An apparent effect of the monolayer coating is the drastic change in wettability of the surface so that the measurement of the contact angle can be considered as an effective way to detect the formation of the SAMs. 

This concept allows the shape of the titration curves to be explained by postulating that the chloroform droplet size decreases as the interfacial tension (ift) between the aqueous and chloroform phases is decreased by the presence of active surfactant. As the endpoint in a titration is approached the amount of active SDBS decreases as it complexes with the injected hyamine. The reduction in the amount of active surfactant material results in an increase... 

The aqueous phases were prepared by dispersing surfactant in D20 or in formation water using magnetic stirring. The solutions were then diluted to the appropriate concentration by the addition of NaCI or CaCI2, or NaOH or HCI concentrates in D20. All concentrations refer to the active surfactant concentration at room temperature. 

Surfactants may exhibit a degree of hydrotropy and thus function as antistatic agents. They are often used for this and for their emulsifying properties in conjunction with fibre lubricants, or may be used alone in a dual capacity as lubricant and antistat. Suitably active surfactants can be found amongst all four ionic types, some typical examples being [471] ... 

Tian Y, Fendler JH (1997) Langmuir-Blodgett film formation from fluorescence-activated, surfactant-capped size selected CdS nanoparticles spread on water surfaces. Chem Mater 8 969-974... 

Perfluorocarbons bearing a polar hydrophilic head are very active surfactants. Indeed, the presence of fluorine atoms strongly lowers the critical micelle concentration (CMC) of an amphiphilic compound. Moreover, fluorination generally has important effects on micellization phenomena, especially on the size and shape of formed micelles. 

The first two components are the active surfactants, whereas the other components are added for a variety of reasons. The polyphosphate chelate Ca ions which are present (with Mg ions also) in so-called hard waters and prevents them from coagulating the anionic surfactants. Zeolite powders are often used to replace phosphate because of their nutrient properties in river systems. Sodium silicate is added as a corrosion inhibitor for washing machines and also increases the pH. The pH is maintained at about 10 by the sodium carbonate. At lower pH values the acid form of the surfactants are produced and in most cases these are either insoluble or much less soluble than the sodium salt. Sodium sulphate is added to prevent caking and ensures free-flowing powder. The cellulose acts as a protective hydrophilic sheath around dispersed dirt particles and prevents re-deposition on the fabric. Foam stabilizers (non-ionic surfactants) are sometimes added to give a... 

The micelle formulation approach often possesses disadvantages such as its toxicity associated with surfactants even at relatively low concentrations. In general, nonionic surfactants have the least toxic effects. Cremophor EL produces hypersensitivity reactions in human and animals (Jonkman-de Vries et al., 1996). Tween-80 is also believed to cause acute hepatitis and renal failure (Uchegbu and Florence, 1996). On intravenous administration, owing to their surface activity, surfactant molecules have the potential to penetrate and disrupt biological membranes and can be hemolytic (Ten Tije et al., 2003). Often the absorption capacity of the micelle is too small and the extent of the... 

The chiral selectors most commonly used as additives in the buffer can be divided into three main categories inclusion systems [e.g., cyclodextrins (CDs) or crown ethers], enantioselective metal-ion complexes [e.g. cop-per(II)-L-histidine or copper(II)-aspartame], and optically active surfactants (e.g., chiral mixed micelles or bile acids). Cyclodextrins are the most widely reported, and they are used in low-pH buffers for the resolution of... 

---