Wet systems

Donald A M 1998 Environmental soanning eleotron miorosoopy for the study of wet systems Curr. Op. Coiioid interface Sc/. 3 143-7... 

Air. Biofilters are an effective way of dealing with air from industrial processes that use halogenated solvents such chloromethane, dichioromethane, chloroethane, 1,2-dichloroethane and vinyl chloride, that support aerobic growth (26). Both compost-based dry systems and trickling filter wet systems are in use. Similar filters could be incorporated into pump-and-treat operations. 

Urethane-Coated Fabrics. Manufacturing methods for urethane-coated fabrics are the dry system and the wet system. 

In the wet system, manufacture proceeds as foUows (/) a 7—20% polyurethane solution of DMF is appHed onto a fabric and immersed in water containing 0—10% of DMF for coagulation (2) the coated fabric is washed and dried (4) the surface is finished by the dry system. For the substrate, a woven or knit fabric which has been bmshed on its surface is often used to improve appearance, resistance to grain break, and feel. 

Wet System Compression M olding. Wet system compression molding was the first high volume method for manufacturing reinforced plastic parts, in such appHcations as the Chevrolet Corvette, industrial trays, tote boxes, luggage, refrigerator liners, and other commercial appHcations. 

Reactivities of several chlorinated solvents, including chloroform, with aluminum, iron, and 2inc in both dry and wet systems have been deterrnined, as have chemical reactivities in oxidation reactions and in reactions with amines (11). Unstabilized wet chloroform reacts completely with aluminum and attacks zinc at a rate of >250 //m/yr and iron at <250 //m/yr. The dry, uiiinhibited solvent attacks aluminum and zinc at a rate of 250 )J.m/yr and iron at 25 ]lni / yr. 

Wet systems, where large quantities of water containing chemicals wash the gas stream... 

The flashed steam method is less efficient and its requirements for steam properties—cleanliness, high temperature, and high pressure— are usually unavailable in most geothermal fields. The situation is different with the binary cycle system, which is quite efficient and widely used. This wet system involves the transfer of heat from the hot well stream into a more manageable boiling fluid to generate power through a turboexpander. 

Semidry Scrubbers The advantage of semidry scrubbers is in that they remove contaminants by way of a solid waste that is easier to dispose of (less expensive). Initially, the scrubbing medium is wet (such as a lime or soda ash slurry). Then a spray dryer is used to atomize the slurry into the gas which evaporates the water in the droplets. As this takes place, the acid in the gas neutralizes the alkali material and forms a fine white solid. Most of the white solids are removed at the bottom of the scrubber while some are carried into the gas stream and have to be removed by a filter or electrostatic precipitator (discussed later). Although semidry systems cost 5-15% more than wet systems, when combined with a fabric filter, they can achieve 90-95% efficiencies. Dry scrubbers are sometimes used in a very similar fashion, but without the help of gas-liquid-solid mass transfer, these systems use much higher amounts of the solid alkali materials. 

Scrubbers and absorbers Wet systems used for the removal of aerosols and other gaseous pollutants from an airstream. 

Oil-wetting systems can be modeled by replacing the glass plate with a plate of polytetrafluoroethylene (PTFE), as shown in the hexadecane/water/PTFE system in Figure 4. At the hexadecane/water interface the water phase did not wet the PTFE surface, the contact angle was thus greater than 90° and the tension decreased. The peak... 

Average temperatures (40-70°C) in combination with high-shear dispersion equipment, of which three-roll mills are a good example, appear to afford the best results in terms of pigment dispersion in wetting systems, such as offset varnish. Fig. 33 shows a curve in which the degree of dispersion reaches a distinct maximum at one particular temperature. 

Kharazipour etal. (1998) used a peroxidase enzyme in combination with H2O2 to activate the surface of TMP fibres for self-bonding. Fibres were activated in a wet system, then dewatered and fluffed out before pressing at 190 °C for 5 minutes. The best IBS recorded for boards of 5 mm thickness made from the activated fibres was 0.55 MPa. The IBS was found to be dependent upon the pH of the treatment solution, the time of treatment and the board density. The authors noted that phenoloxidase gave comparable results to laccase, which was unexpected, since it was thought that the phenoloxidase would lead only to depolymerization of the lignin. 

An infrared spectrum is a plot of percent radiation absorbed versus the frequency of the incident radiation given in wavenumbers (cm ) or in wave length ( xm). A variation of this method, diffuse reflectance spectroscopy, is used for samples with poor transmittance, e.g. cubic hematite crystals. Increased resolution and sensitivity as well as more rapid collection of data is provided by Fourier-transform-IR (FTIR), which averages a large number of spectra. Another IR technique makes use of attenuated total reflectance FTIR (ATR-FTIR) often using a cylindrical internal reflectance cell (CIR) (e.g. Tejedor-Tejedor Anderson, 1986). ATR enables wet systems and adsorbing species to be studied in situ. 

All the plants have been installed in the existing gathering centres and these Installations had to conform to existing facilities and available plant area. Certain relocations and modifications of the existing facilities were done to accommodate the new plant. For gas separation from wet crude, one bank or existing two-phase gas-oil separatory has been segregated ar.d tied into the wet system. 

The differential-pressure transmitters are only available for moderate pressures, up to 400 bar. Membrane systems give the possibility of choosing corrosion-resistent materials for the parts of a device (wet system), or to protect the inside of the device by using an additional membrane which divides the instrument side from corrosive media (dry system). 

The addition of SMC and BMC to reinforced polyesters has changed the basic mechanical property picture very little. The same is true for low profile polyesters. The mechanical performance is at the same general level that is attained with the older wet systems, such as preform and mat, and premix molding. 

---