Viscosity control

Polyacrylamides are used in many other oilfield appUcations. These include cement additives for fluid loss control in well cementing operations (127), viscosity control additives for drilling muds (128), and fracturing fluids (129). Copolymers [40623-73-2] of acrylamide and acrylamidomethylpropanesulfonic acid do not degrade with the high concentrations of acids used in acid fracturing. 

Synthetic lubricants are made with neopentyl glycol in the base-stock polyester (24). Excellent thermal stabiHty and viscosity control are imparted to special high performance aviation lubricants by the inclusion of polyester thickening agents made from neopentyl glycol (25,26) (see LUBRICATION AND lubricants). Neopentyl glycol is also used to manufacture polymeric plasticizers that exhibit the improved thermal, hydrolytic, and uv stabiHty necessary for use in some exterior appHcations (27). 

Chocolate does not behave as a tme Hquid owing to the presence of cocoa particles and the viscosity control of chocolate is quite compHcated. This non-Newtonian behavior has been described (28). When the square root of the rate of shear is plotted against the square root of shear stress for chocolate, a straight line is produced. With this Casson relationship method (29) two values are obtained, Casson viscosity and Casson yield value, which describe the flow of chocolate. The chocolate industry was slow in adopting the Casson relationship but this method now prevails over the simpler MacMichael viscometer. Instmments such as the Carri-Med Rheometer and the Brookfield and Haake Viscometers are now replacing the MacMichael. 

The polysulfide impression materials can be formulated to have a wide range of physical and chemical characteristics by modifying the base (polysulfide portion), and/or the initiator system. Further changes may be obtained by varying the proportion of the base to the catalyst in the final mix. Characteristics varied by these mechanisms include viscosity control from thin fluid mixes to heavy thixotropic mixes, setting-time control, and control of the set-mbber hardness from a Shore A Durometer scale of 20 to 60. Variations in strength, toughness, and elasticity can also be achieved. 

The bulk viscosity control parameter for CSM, as with other elastomers, is molecular weight M and molecular-weight distribution (MWD). Mooney viscosity for CSM is determined by selection of the polyethylene precursor. 

General References Apian and Spedden, Viscosity Control in Heavy... 

All of the eommereial alkyl eyanoaerylate monomers are low-viseosity liquids, and for some applications this can be an advantage. However, there are instances where a viseous liquid or a gel adhesive would be preferred, sueh as for application to a vertical surface or on porous substrates. A variety of viscosity control agents, depending upon the desired properties, have been added to increase the viscosity of instant adhesives [21]. The materials, which have been utilized, include polymethyl methacrylate, hydrophobic silica, hydrophobic alumina, treated quartz, polyethyl cyanoacrylate, cellulose esters, polycarbonates, and carbon black. For example, the addition of 5-10% of amorphous, non-crystalline, fumed silica to ethyl cyanoacrylate changes the monomer viscosity from a 2-cps liquid to a gelled material [22]. Because of the sensitivity of cyanoacrylate esters to basic materials, some additives require treatment with an acid to prevent premature gelation of the product. 

The formaldehyde-to-phenol molar ratios of most novolacs lie somewhere between 0.30 and 0.99. This is a very broad range in the eyes of a novolac chemist. Novolacs are extremely sensitive to molar ratio variation and they are usually specified to the nearest 0.001 molar ratio unit or less. Also unlike resoles, one does not have the option of selecting the development of molecular weight through viscosity control. The molecular weight and viscosity are largely determined by... 

Electrical properties of liquids and solids are sometimes crucially influenced by H bonding. The ionic mobility and conductance of H30 and OH in aqueous solutions are substantially greater than those of other univalent ions due to a proton-switch mechanism in the H-bonded associated solvent, water. For example, at 25°C the conductance of H3O+ and OH are 350 and 192ohm cm mol , whereas for other (viscosity-controlled) ions the values fall... 

Examples of commonly used viscosity control additives are calcium ligno-sulfonate, sodium chloride and some long-chain polymers. These additives also act as accelerators or retarders so care must be taken in designing the cement slurry with these materials. 

In solution polymerization, an organic solvent dissolves the monomer. Solvents should have low chain transfer activity to minimize chain transfer reactions that produce low-molecular-weight polymers. The presence of a solvent makes heat and viscosity control easier than in bulk polymerization. Removal of the solvent may not be necessary in certain applications such as coatings and adhesives. 

The recovery of petroleum from sandstone and the release of kerogen from oil shale and tar sands both depend strongly on the microstmcture and surface properties of these porous media. The interfacial properties of complex liquid agents—mixtures of polymers and surfactants—are critical to viscosity control in tertiary oil recovery and to the comminution of minerals and coal. The corrosion and wear of mechanical parts are influenced by the composition and stmcture of metal surfaces, as well as by the interaction of lubricants with these surfaces. Microstmcture and surface properties are vitally important to both the performance of electrodes in electrochemical processes and the effectiveness of catalysts. Advances in synthetic chemistry are opening the door to the design of zeolites and layered compounds with tightly specified properties to provide the desired catalytic activity and separation selectivity. 

Commercial products are listed in the literature. These include bactericides, corrosion inhibitors, defoamers, emulsifiers, fluid loss and viscosity control agents, and shale control additives [58-61,65]. 

The viscosity of a cement affects the pumping properties. The viscosity must be kept low enough to ensure pumpability of the slurry during the entire operation period. In deep wells, because of the increased temperature, the viscosity becomes increasingly lower, which leads to undesirable flow characteristics of the slurry. This effect can be serious, because the viscosity follows the Arrhenius law. Some of the additives used for viscosity control also... 

These humic acids are not dissolved because the pH of this slurry is in the range of 4 to 9. Small amounts of fulvic acids are formed, and these are soluble in the water of the slurry. The coal-derived humic acids find applications as drilling fluid dispersants and viscosity control agents, whereas the coal-derived fulvic acids may be used to produce plasticizers and petrochemicals. 

Turner, S.R., Walker, T.O. and Thaler, W.A. "Sodium Styrene Sulfonate Co-Sodium N-(4-Sulfo Phenyl) Maleimide An Improved Viscosity Control Additive," US Patent 4,478,727(1984). 

---