Vinyl chloride nature

Vinyl chloride (chloroethene). The production of vinyl chloride naturally attracted the attention of those companies already involved in chlorination processes. The quantities of by-product hydrogen chloride available were often an embarrassment and the relatively facile production of vinyl chloride from acetylene and anhydrous HCl, over a supported mercuric chloride catalyst, provided a valuable outlet. 

D Acetone, ammonia, benzene, butane, cyclopropane, ethanol, gasoline, hexane, methanol, methane, vinyl chloride, natural gas, naphtha, propane, or gases of equivalent hazard. ... 

Fig. 37. Diffusion coefficient as a function of molar volume for a variety of permeants in natural mbber and in poly(vinyl chloride) (PVC) (81—83).

Partial oxidation of natural gas or a fuel oil using oxygen may be used to form acetylene, ethylene (qv) and propylene (qv). The ethylene in turn may be partially oxidi2ed to form ethylene oxide (qv) via advantages (/) and (5). A few of the other chemicals produced using oxygen because of advantages (/) and (5) are vinyl acetate, vinyl chloride, perchloroethylene, acetaldehyde (qv), formaldehyde (qv), phthaHc anhydride, phenol (qv), alcohols, nitric acid (qv), and acryhc acid. 

Uses. Phthabc anhydride is used mainly in plasticizers, unsaturated polyesters, and alkyd resins (qv). PhthaUc plasticizers consume 54% of the phthahc anhydride in the United States (33). The plasticizers (qv) are used mainly with poly(vinyl chloride) to produce flexible sheet such as wallpaper and upholstery fabric from normally rigid polymers. The plasticizers are of two types diesters of the same monohydric alcohol such as dibutyl phthalate, or mixed esters of two monohydric alcohols. The largest-volume plasticizer is di(2-ethylhexyl) phthalate [117-81-7] which is known commercially as dioctyl phthalate (DOP) and is the base to which other plasticizers are compared. The important phthahc acid esters and thek physical properties are Hsted in Table 12. The demand for phthahc acid in plasticizers is naturally tied to the growth of the flexible poly(vinyl chloride) market which is large and has been growing steadily. 

Other typical pyrotechnic fuels include charcoal, sulfur, boron, siUcon, and synthetic polymers such as poly(vinyl alcohol) and poly(vinyl chloride). Extensive use has been made of natural products such as starches and gums, and the use of these materials continues to be substantial in the fireworks industry. MiUtary pyrotechnics have moved away from the use of natural products due to the inherent variabiUty in these materials depending on climatic conditions during the growth of the plants from which the compounds are derived. 

The thermoplastic or thermoset nature of the resin in the colorant—resin matrix is also important. For thermoplastics, the polymerisation reaction is completed, the materials are processed at or close to their melting points, and scrap may be reground and remolded, eg, polyethylene, propjiene, poly(vinyl chloride), acetal resins (qv), acryhcs, ABS, nylons, ceUulosics, and polystyrene (see Olefin polymers Vinyl polymers Acrylic ester polymers Polyamides Cellulose ESTERS Styrene polymers). In the case of thermoset resins, the chemical reaction is only partially complete when the colorants are added and is concluded when the resin is molded. The result is a nonmeltable cross-linked resin that caimot be reworked, eg, epoxy resins (qv), urea—formaldehyde, melamine—formaldehyde, phenoHcs, and thermoset polyesters (qv) (see Amino resins and plastics Phenolic resins). 

There is much evidence that weak links are present in the chains of most polymer species. These weak points may be at a terminal position and arise from the specific mechanism of chain termination or may be non-terminal and arise from a momentary aberration in the modus operandi of the polymerisation reaction. Because of these weak points it is found that polyethylene, polytetrafluoroethylene and poly(vinyl chloride), to take just three well-known examples, have a much lower resistance to thermal degradation than low molecular weight analogues. For similar reasons polyacrylonitrile and natural rubber may degrade whilst being dissolved in suitable solvents. 

Most toxicity problems associated with the finished product arise from the nature of the additives and seldom from the polymer. Mention should, however, be made of poly(vinyl carbazole) and the polychloroacrylates which, when monomer is present, can cause unpleasant effects, whilst in the 1970s there arose considerable discussion on possible links between vinyl chloride and a rare form of cancer known as angiosarcoma of the liver. 

A number of higher poly(vinyl ether)s, in particular the ethyl and butyl polymers, have found use as adhesives. When antioxidants are incorporated, pressure-sensitive adhesive tapes from poly(vinyl ethyl ether) are said to have twice the shelf life of similar tapes from natural rubber. Copolymers of vinyl isobutyl ether with methyl acrylate and ethyl acrylate (Acronal series) and with vinyl chloride have been commercially marketed. The first two products have been used as adhesives and impregnating agents for textile, paper and leather whilst the latter (Vinoflex MP 400) has found use in surface coatings. 

Liver cancer can also be a consequence of exposure to hepatotoxic chemicals. Natural hepatocarcinogens include fungal aflatoxins. Synthetic hepato-carcinogens include nitrosoamines, certain chlorinated hydrocarbons, polychlorinated biphenyls (PCBs), chloroform, carbon tetrachloride, dimethyl-benzanthracene, and vinyl chloride.Table 5.15 lists the chemical compounds that induce liver cancer or cirrhosis in experimental animals or... 

The number of clear human epidemiologic studies is small. A total of approximately 50 compounds (c.g., benzene, vinyl chloride) and complex e.xposures (e.g., aluminum production, tobacco smoke) have sufficient data available to permit their classification as human carcinogens. The most potent human carcinogens known, the aflatoxins. are of natural origin. Their presence in food products through infestation by toxin-producing fungi constitute a serious problem in several tropical and subtropical countries. 

The estimation of reactivity of polyhalomethanes in the reactions with the same monomer shows that the quantity of halogen atoms in a molecule is the most essential factor affecting the easiness of homolysis of even one C— Br bond in molecule, and the influence of the halogen nature (chlorine or bromine) is of less significance. For instance, the analysis of the data on relative kinetics of some polyhalomethanes reactions with vinyl chloride allows us to grade the studied polyhalomethanes according to their reactivity, as follows ... 

All of the above high-volume organic chemicals are obtained from petroleum or natural gas. This is why the modern organic chemical industry is frequently referred to as the petrochemical industry. The high-volume status of some of these compounds is due to their use to make others lower on the list. For example, ethylene is used to make ethylene dichloride, which, in turn, is used to make vinyl chloride. Ethyl benzene, made from benzene and ethylene, is used to make styrene. Methyl r-butyl ether is made from methanol and butylene, a captive intermediate for which production data is not available. 

Bloom Y, R Aravena, D Hunkeler, E Edwards, SK Frape (2000) Carbon isotope fractionation during microbial dechlorination of trichlorothene, cw-l,2-dichloroethene, and vinyl chloride implications for assessment of natural attenuation. Environ Sci Technol 34 2768-2772. 

---