Vapor-phase ethylene process

Most of the vinyl acetate produced in the United States is made by the vapor-phase ethylene process. In this process, a vapor-phase mixture of ethylene, acetic acid, and oxygen is passed at elevated temperature and pressures over a fixed-bed catalyst consisting of supported palladium (85). Less than 70% oxygen, acetic acid, and ethylene conversion is realized per pass. Therefore, these components have to be recovered and returned to the reaction zone. The vinyl acetate yield using this process is typically in the 91—95% range (86). Vinyl acetate can be manufactured also from acetylene, acetaldehyde, and the hquid-phase ethylene process (see Vinyl polymers). 

Most of the vinyl acetate produced in the United States is made by the vapor-phase ethylene process. 

Alkylation. Ethylbenzene [100-41 -4] the precursor of styrene, is produced from benzene and ethylene. The ethylation of benzene is conducted either ia the Hquid phase ia the preseace of a Eriedel-Crafts catalyst (AlCl, BE, EeCl ) or ia the vapor phase with a suitable catalyst. The Moasanto/Lummus process uses an aluminum chloride catalyst that yields more than 99% ethylbenzene (13). More recently, Lummus and Union Oil commercialized a zeoHte catalyst process for Hquid-phase alkylation (14). Badger and Mobil also have a vapor-phase alkylation process usiag zeoHte catalysts (15). Almost all ethylbenzene produced is used for the manufacture of styrene [100-42-5] which is obtained by dehydrogenation ia the preseace of a suitable catalyst at 550—640°C and relatively low pressure, <0.1 MPa (<1 atm). 

The vapor-phase Badger process (Eigure 10-2), which has been commercialized since 1980, can accept dilute ethylene streams such as those produced from ECC off gas. A zeolite type heterogeneous catalyst is used in a fixed bed process. The reaction conditions are 420°C and 200-300 psi. Over 98% yield is obtained at 90% conversion." Polyethylbenzene (polyalkylated) and unreacted benzene are recycled and join the fresh feed to the reactor. The reactor effluent is fed to the benzene fractionation system to recover unreacted benzene. The bottoms... 

The reachon of benzene with ethylene or propylene to form ethylbenzene or isopropylbenzene (cumene) is an industrially important transformahon, with ethylbenzene as the key building block for polystyrene and cumene as the feedstock for phenol produchon [55]. Fthylbenzene was originally produced with a Lewis acid catalyst consishng of AlCfi or a Bronsted acidic solid phosphoric acid (SPA) catalyst [56]. Both catalyst systems suffered from equipment corrosion so, in the 1980s the Mobil-Badger vapor phase alkylation process was introduced, which... 

In the EBMax process, benzene is fed to the bottom of the liquid-filled multibed reactor. Ethylene is co-fed with the benzene and also between the catalyst beds. Polyethylbenzenes, which are almost exclusively diethylbenzenes, undergo transalkylation with benzene in a second reactor. Mobil-Badger offers both liquid phase and vapor phase transalkylation processes. The vapor phase process removes benzene feed coboilers such as cyclohexane and methylcyclopentane as well as propyl and butylbenzenes. Because the EBMax process produces very low levels of propyl and butylbenzenes, for most applications, the more energy efficient liquid phase process is preferred. Worldwide, there are currently ten licensed EBMax units with a cumulative ethylbenzene production capacity of five million metric tons per year. 

Action of HCN in the presence of oxygen Asahiznd Du Pont have developed a process for vapor phase ethylene conversion, between 330 and360°C, on nickel- or palladium-based... 

The ethylene-based version of the vinyl acetate process was also developed by Wacker Chemie. The process is similar to the Wacker process for acetaldehyde from ethylene which was developed about the same time. In the vinyl acetate process, ethylene is reacted with high purity oxygen and acetic acid in the presence of a palladium chloride catalyst. National Distillers and Chemicals, which later became USI chemicals and is now a division of Quantum Chemicals, developed a similar vapor phase ethylene-based technology in the United States. Both versions of the process are presently used commercially [25,26]. 

A liquid phase ethylene process was developed by several groups simultaneously, but it was never commercialized. Severe corrosion as well as other technical difficulties rendered the process uneconomical compared with the vapor phase version. 

Direct hydration of propylene in a vapor-phase, catalytic process also is commercially practiced. This is similar to hydration of ethylene to make ethanol. Relative to the sulfuric acid-mediated process, it offers the advantage of decreased corrosion. However, it suffers from a requirement for a pure propylene feed, whereas the former process can be used with a dilute, refinery stream. 

In manufacturing ethylene from reduced crude oil or residues, the feed is heated and sent to a flash or evaporator chamber to vaporize a gas-oil or distillate fraction, as practiced in the early Gyro Vapor Phase cracking process for the production of ethylene. Steam is used to assist in the vaporization and to reduce the partial pressure in the reaction zone as... 

Liquid- and vapor-phase processes have been described the latter appear to be advantageous. Supported cadmium, zinc, or mercury salts are used as catalysts. In 1963 it was estimated that 85% of U.S. vinyl acetate capacity was based on acetylene, but it has been completely replaced since about 1982 by newer technology using oxidative addition of acetic acid to ethylene (2) (see Vinyl polymers). In western Europe production of vinyl acetate from acetylene stiU remains a significant commercial route. 

Processes rendered obsolete by the propylene ammoxidation process (51) include the ethylene cyanohydrin process (52—54) practiced commercially by American Cyanamid and Union Carbide in the United States and by I. G. Farben in Germany. The process involved the production of ethylene cyanohydrin by the base-cataly2ed addition of HCN to ethylene oxide in the liquid phase at about 60°C. A typical base catalyst used in this step was diethylamine. This was followed by liquid-phase or vapor-phase dehydration of the cyanohydrin. The Hquid-phase dehydration was performed at about 200°C using alkah metal or alkaline earth metal salts of organic acids, primarily formates and magnesium carbonate. Vapor-phase dehydration was accomphshed over alumina at about 250°C. 

Vinyl ethers are prepared in a solution process at 150—200°C with alkaH metal hydroxide catalysts (32—34), although a vapor-phase process has been reported (35). A wide variety of vinyl ethers are produced commercially. Vinyl acetate has been manufactured from acetic acid and acetylene in a vapor-phase process using zinc acetate catalyst (36,37), but ethylene is the currently preferred raw material. Vinyl derivatives of amines, amides, and mercaptans can be made similarly. A/-Vinyl-2-pyrroHdinone is a commercially important monomer prepared by vinylation of 2-pyrroHdinone using a base catalyst. 

Ethjlben ne Synthesis. The synthesis of ethylbenzene for styrene production is another process in which ZSM-5 catalysts are employed. Although some ethylbenzene is obtained direcdy from petroleum, about 90% is synthetic. In earlier processes, benzene was alkylated with high purity ethylene in liquid-phase slurry reactors with promoted AlCl catalysts or the vapor-phase reaction of benzene with a dilute ethylene-containing feedstock with a BF catalyst supported on alumina. Both of these catalysts are corrosive and their handling presents problems. 

These operations have been gradually replaced by the Mobd-Badger process (28), which employs an acidic ZSM-5 catalyst and produces ethylbenzene using both pure and dilute ethylene sources. In both cases, the alkylation is accomplished under vapor-phase conditions of about 425°C,... 

Propanol has been manufactured by hydroformylation of ethylene (qv) (see Oxo process) followed by hydrogenation of propionaldehyde or propanal and as a by-product of vapor-phase oxidation of propane (see Hydrocarbon oxidation). Celanese operated the only commercial vapor-phase oxidation faciUty at Bishop, Texas. Since this faciUty was shut down ia 1973 (5,6), hydroformylation or 0x0 technology has been the principal process for commercial manufacture of 1-propanol ia the United States and Europe. Sasol ia South Africa makes 1-propanol by Fischer-Tropsch chemistry (7). Some attempts have been made to hydrate propylene ia an anti-Markovnikoff fashion to produce 1-propanol (8—10). However, these attempts have not been commercially successful. 

Styrene. Commercial manufacture of this commodity monomer depends on ethylbenzene, which is converted by several means to a low purity styrene, subsequendy distilled to the pure form. A small percentage of styrene is made from the oxidative process, whereby ethylbenzene is oxidized to a hydroperoxide or alcohol and then dehydrated to styrene. A popular commercial route has been the alkylation of benzene to ethylbenzene, with ethylene, after which the cmde ethylbenzene is distilled to give high purity ethylbenzene. The ethylbenzene is direcdy dehydrogenated to styrene monomer in the vapor phase with steam and appropriate catalysts. Most styrene is manufactured by variations of this process. A variety of catalyst systems are used, based on ferric oxide with other components, including potassium salts, which improve the catalytic activity (10). 

In oxychlorination, ethylene reacts with dry HCl and either air or pure oxygen to produce EDC and water. Various commercial oxychlorination processes differ from one another to some extent because they were developed independentiy by several different vinyl chloride producers (78,83), but in each case the reaction is carried out in the vapor phase in either a fixed- or fluidized-bed reactor containing a modified Deacon catalyst. Unlike the Deacon process for chlorine production, oxychlorination of ethylene occurs readily at temperatures weU below those requited for HCl oxidation. 

In recent years alkylations have been accompHshed with acidic zeoHte catalysts, most nobably ZSM-5. A ZSM-5 ethylbenzene process was commercialized joiatiy by Mobil Co. and Badger America ia 1976 (24). The vapor-phase reaction occurs at temperatures above 370°C over a fixed bed of catalyst at 1.4—2.8 MPa (200—400 psi) with high ethylene space velocities. A typical molar ethylene to benzene ratio is about 1—1.2. The conversion to ethylbenzene is quantitative. The principal advantages of zeoHte-based routes are easy recovery of products, elimination of corrosive or environmentally unacceptable by-products, high product yields and selectivities, and high process heat recovery (25,26). 

There are two main processes for the synthesis of ethyl alcohol from ethylene. The eadiest to be developed (in 1930 by Union Carbide Corp.) was the indirect hydration process, variously called the strong sulfuric acid—ethylene process, the ethyl sulfate process, the esterification—hydrolysis process, or the sulfation—hydrolysis process. This process is stiU in use in Russia. The other synthesis process, designed to eliminate the use of sulfuric acid and which, since the early 1970s, has completely supplanted the old sulfuric acid process in the United States, is the direct hydration process. This process, the catalytic vapor-phase hydration of ethylene, is now practiced by only three U.S. companies Union Carbide Corp. (UCC), Quantum Chemical Corp., and Eastman Chemical Co. (a Division of Eastman Kodak Co.). UCC imports cmde industrial ethanol, CIE, from SADAF (the joint venture of SABIC and Pecten [Shell]) in Saudi Arabia, and refines it to industrial grade. 

Ethylene. Where ethylene is ia short supply and fermentation ethanol is made economically feasible, such as ia India and Bra2il, ethylene is manufactured by the vapor-phase dehydration of ethanol. The production of ethylene [74-85-1] from ethanol usiag naturally renewable resources is an active and useful alternative to the pyrolysis process based on nonrenewable petroleum. This route may make ethanol a significant raw material source for produciag other chemicals. 

Manufacture. Much of the diethyl ether manufactured is obtained as a by-product when ethanol (qv) is produced by the vapor-phase hydration of ethylene (qv) over a supported phosphoric acid catalyst. Such a process has the flexibiHty to adjust to some extent the relative amounts of ethanol and diethyl ether produced in order to meet existing market demands. Diethyl ether can be prepared directly to greater than 95% yield by the vapor-phase dehydration of ethanol in a fixed-bed reactor using an alumina catalyst (21). 

The per pass ethylene conversion in the primary reactors is maintained at 20—30% in order to ensure catalyst selectivities of 70—80%. Vapor-phase oxidation inhibitors such as ethylene dichloride or vinyl chloride or other halogenated compounds are added to the inlet of the reactors in ppm concentrations to retard carbon dioxide formation (107,120,121). The process stream exiting the reactor may contain 1—3 mol % ethylene oxide. This hot effluent gas is then cooled ia a shell-and-tube heat exchanger to around 35—40°C by usiag the cold recycle reactor feed stream gas from the primary absorber. The cooled cmde product gas is then compressed ia a centrifugal blower before entering the primary absorber. 

In order to assure control of the reaction, the vapor-phase inhibitor concentration must be closely controlled in the ppm range. Although several compounds have been claimed to be useful, it is likely that commercial processes use only ethylene dichloride or some of the simpler chlorinated aromatics (102). In general, the choice between inhibitors is not based on their differences in performance, but rather on the designers preference for dealing with the type of control problems each inhibitor system imposes (102). 

---