Vanadium phases

Vanadium deposits in the surroundings of the active phase cause active site poisoning due to the coverage of the active phase or the edges. Active site generation occurs by the formation of isolated vanadium phase on the support material which has catalytic activity for hydrodemetallisation. Both phenomena could explain the UV-Vis results of the liquid effluent. Apparently the nett effect is zero catalyst deactivation up to 9 wt.% vanadium deposition. 

Benzene oxidation to maleic anhydride CeHg + 02 C4H2O3 350 "C 1 bar V2O5/M0O2/ AI2O3 1-2 formation of an inactive vanadium phase... 

The reaction uses a fixed-bed vanadium pentoxide-titanium dioxide catalyst which gives good selectivity for phthalic anhydride, providing temperature is controlled within relatively narrow limits. The reaction is carried out in the vapor phase with reactor temperatures typically in the range 380 to 400°C. 

Commercially, maleic anhydride is prepared more cheaply by the catalytic vapour phase oxidation (in the presence of vanadium pentoxide at about 400°) of benzene with atmospheric oxygen ... 

Acetylation of acetaldehyde to ethyUdene diacetate [542-10-9], a precursor of vinyl acetate, has long been known (7), but the condensation of formaldehyde [50-00-0] and acetic acid vapors to furnish acryflc acid [97-10-7] is more recent (30). These reactions consume relatively more energy than other routes for manufacturing vinyl acetate or acryflc acid, and thus are not likely to be further developed. Vapor-phase methanol—methyl acetate oxidation using simultaneous condensation to yield methyl acrylate is still being developed (28). A vanadium—titania phosphate catalyst is employed in that process. 

Vapor-phase oxidation over a promoted vanadium pentoxide catalyst gives a 90% yield of maleic anhydride [108-31-6] (139). Liquid-phase oxidation with a supported palladium catalyst gives 55% of succinic acid [110-15-6] (140). 

Phase transitions are involved in critical temperature thermistors. Vanadium, VO2, and vanadium trioxide [1314-34-7] V2O3, have semiconductors—metal transitions in which the conductivity decreases by several orders of magnitude on cooling. Electronic phase transitions are also observed in superconducting ceramics like YBa2Cu30y but here the conductivity increases sharply on cooling through the phase transition. 

Vanadium—Cobalt-Iron Alloys. V—Co—Fe permanent-magnet alloys also are ductile. A common commercial ahoy, Vicahoy I, has a nominal composition 10 wt % V, 52 wt % Co, and 38 wt % Fe (Table 10). Hard magnetic properties are developed by quenching from 1200°C for conversion to bcc a-phase foUowed by aging at 600°C (precipitation of fee y-phase). The resulting properties are isotropic, with ca kJ/m ... 

The catalyst used in the production of maleic anhydride from butane is vanadium—phosphoms—oxide (VPO). Several routes may be used to prepare the catalyst (123), but the route favored by industry involves the reaction of vanadium(V) oxide [1314-62-1] and phosphoric acid [7664-38-2] to form vanadyl hydrogen phosphate, VOHPO O.5H2O. This material is then heated to eliminate water from the stmcture and irreversibly form vanadyl pyrophosphate, (V(123,124). Vanadyl pyrophosphate is befleved to be the catalyticaHy active phase required for the conversion of butane to maleic anhydride (125,126). 

Promoters are sometimes added to the vanadium phosphoms oxide (VPO) catalyst during synthesis (129,130) to increase its overall activity and/or selectivity. Promoters may be added during formation of the catalyst precursor (VOHPO O.5H2O), or impregnated onto the surface of the precursor before transformation into its activated phase. They ate thought to play a twofold stmctural role in the catalyst (130). First, promoters facilitate transformation of the catalyst precursor into the desired vanadium phosphoms oxide active phase, while decreasing the amount of nonselective VPO phases in the catalyst. The second role of promoters is to participate in formation of a soHd solution which controls the activity of the catalyst. 

The bulk stmcture of the catalyticaHy active phase is not completely known and is under debate in the Hterature (125,131—133). The central point of controversy is whether (Valone or in combination with other phases is the most catalyticaHy active for the conversion of butane to maleic anhydride. The heart of this issue concerns the role of stmctural disorder in the bulk and how it arises in the catalyst (125,134,135). Most researchers agree that the catalysts with the highest activity and selectivity ate composed mainly of (Vthat exhibits a clustered or distorted platelet morphology (125). It is also generaHy acknowledged that during operation of the catalyst, the bulk oxidation state of the vanadium in the catalyst remains very close to the +4 valence state (125). 

Benzene-Based Catalyst Technology. The catalyst used for the conversion of ben2ene to maleic anhydride consists of supported vanadium oxide [11099-11-9]. The support is an inert oxide such as kieselguhr, alumina [1344-28-17, or sUica, and is of low surface area (142). Supports with higher surface area adversely affect conversion of benzene to maleic anhydride. The conversion of benzene to maleic anhydride is a less complex oxidation than the conversion of butane, so higher catalyst selectivities are obtained. The vanadium oxide on the surface of the support is often modified with molybdenum oxides. There is approximately 70% vanadium oxide and 30% molybdenum oxide [11098-99-0] in the active phase for these fixed-bed catalysts (143). The molybdenum oxide is thought to form either a soUd solution or compound oxide with the vanadium oxide and result in a more active catalyst (142). 

Oxidation. Naphthalene may be oxidized direcdy to 1-naphthalenol (1-naphthol [90-15-3]) and 1,4-naphthoquinone, but yields are not good. Further oxidation beyond 1,4-naphthoquinone [130-15-4] results in the formation of ortho- h. h5 ic acid [88-99-3], which can be dehydrated to form phthaUc anhydride [85-44-9]. The vapor-phase reaction of naphthalene over a catalyst based on vanadium pentoxide is the commercial route used throughout the world. In the United States, the one phthaUc anhydride plant currently operating on naphthalene feedstock utilizes a fixed catalyst bed. The fiuid-bed process plants have all been shut down, and the preferred route used in the world is the fixed-bed process. 

The anhydride of 1,8-naphthalenedicarboxyHc acid is obtained in ca 95—116 wt % yield by the vapor-phase air-oxidation of acenaphthene at ca 330—450°C, using unsupported or supported vanadium oxide catalysts, with or without modifiers (96). 

Manufacture and Processing. Until World War II, phthaUc acid and, later, phthaUc anhydride, were manufactured primarily by Hquid-phase oxidation of suitable feedstocks. The favored method was BASF s oxidation of naphthalene [91-20-3] by sulfuric acid ia the presence of mercury salts to form the anhydride. This process was patented ia 1896. During World War I, a process to make phthaUc anhydride by the oxidation of naphthalene ia the vapor phase over a vanadium and molybdenum oxide catalyst was developed ia the United States (5). Essentially the same process was developed iadependendy ia Germany, with U.S. patents being granted ia 1930 and 1934 (6,7). 

Fixed-Bed Vapor-Phase Oxidation of Naphthalene. A sihca gel or sihcon carbide support is used for catalyst involved in the oxidation of naphthalene. The typical naphthalene oxidation catalyst is a mixture of vanadium oxide and alkali metal sulfate on the siUca support. Some changes, such as the introduction of feed vaporizers, are needed to handle a naphthalene feed (14), but otherwise the equipment is the same. 

Durene. The oxidation of durene (4) yields pyromeUitic acid [89-05-4] (17) or pyromeUitic dianhydride [89-32-7] (18) directly. The oxidation can be carried out with dilute nitric acid ia solution, with air and catalyst either ia the vapor phase over a soHd vanadium pentoxide-based catalyst or ia the... 

The predominant process for manufacture of aniline is the catalytic reduction of nitroben2ene [98-95-3] ixh. hydrogen. The reduction is carried out in the vapor phase (50—55) or Hquid phase (56—60). A fixed-bed reactor is commonly used for the vapor-phase process and the reactor is operated under pressure. A number of catalysts have been cited and include copper, copper on siHca, copper oxide, sulfides of nickel, molybdenum, tungsten, and palladium—vanadium on alumina or Htbium—aluminum spinels. Catalysts cited for the Hquid-phase processes include nickel, copper or cobalt supported on a suitable inert carrier, and palladium or platinum or their mixtures supported on carbon. 

Alloys of the P type respond to heat treatment, are characterized by higher density than pure titanium, and are more easily fabricated. The purpose of alloying to promote the P phase is either to form an aE-P-phase aEoy having commercially useful quaUties, to form aEoys that have duplex a- and P-stmcture to enhance he at-treatment response, ie, changing the a and P volume ratio, or to use P-eutectoid elements for intermetallic hardening. The most important commercial P-aEoying element is vanadium. 

Silicon Reduction. The preparation of ferrovanadium by the reduction of vanadium concentrates with ferrosiUcon has been used but not extensively. It involves a two-stage process in which technical-grade vanadium pentoxide, ferrosiUcon, lime, and fluorspar are heated in an electric furnace to reduce the oxide an iron alloy containing ca 30 wt % vanadium but undesirable amounts of siUcon is produced. The siUcon content of the alloy is then decreased by the addition of more V2O5 and lime to effect the extraction of most of the siUcon into the slag phase. An alternative process involves the... 

Examination of the metallic product (regulus) of such aluminothermically produced vanadium metal reveals the presence of oxide phases in the metal matrix. This suggests that there is a decreasing solubiHty for aluminum and oxygen below the melting point. To date, no purification processes have been developed that take advantage of the purification potential of this phenomenon. 

Va.na.dium (II) Oxide. Vanadium(II) oxide is a non stoichiometric material with a gray-black color, metallic luster, and metallic-type electrical conductivity. Metal—metal bonding increases as the oxygen content decreases, until an essentially metal phase containing dissolved oxygen is obtained (14). 

The ore is ordinarily ground to pass through a ca 1.2-mm (14-mesh) screen, mixed with 8—10 wt % NaCl and other reactants that may be needed, and roasted under oxidising conditions in a multiple-hearth furnace or rotary kiln at 800—850°C for 1—2 h. Temperature control is critical because conversion of vanadium to vanadates slows markedly at ca 800°C, and the formation of Hquid phases at ca 850°C interferes with access of air to the mineral particles. During roasting, a reaction of sodium chloride with hydrous siUcates, which often are present in the ore feed, yields HCl gas. This is scmbbed from the roaster off-gas and neutralized for pollution control, or used in acid-leaching processes at the mill site. 

Minor uses of vanadium chemicals are preparation of vanadium metal from refined pentoxide or vanadium tetrachloride Hquid-phase organic oxidation reactions, eg, production of aniline black dyes for textile use and printing inks color modifiers in mercury-vapor lamps vanadyl fatty acids as driers in paints and varnish and ammonium or sodium vanadates as corrosion inhibitors in flue-gas scmbbers. 

Oxidation. Benzene can be oxidized to a number of different products. Strong oxidizing agents such as permanganate or dichromate oxidize benzene to carbon dioxide and water under rigorous conditions. Benzene can be selectively oxidized in the vapor phase to maleic anhydride. The reaction occurs in the presence of air with a promoted vanadium pentoxide catalyst (11). Prior to 1986, this process provided most of the world s maleic anhydride [108-31 -6] C4H2O2. Currendy maleic anhydride is manufactured from the air oxidation of / -butane also employing a vanadium pentoxide catalyst. 

The vapor-phase oxidation (VPO) of butadiene with air at 200—500°C produces maleic anhydride [108-31-6]. Catalysts used are based on vanadium and molybdenum oxides (89,90). Alternatively, when using a catalyst containing Al, Mo, and Ti, butadiene undergoes a complex series of condensations and oxidations to form anthraquinone at 250°C (91). 

The active phase, which is soHd at room temperature, is comprised of mixed potassium and sodium vanadates and pyrosulfates, whereas the support is macroporous siUca, usually in the form of 6—12 mm diameter rings or pellets. The patent Hterature describes a number of ways to prepare the catalyst a typical example contains 7 wt % vanadium pentoxide, 8% potassium added as potassium hydroxide or carbonate, 1% sodium, and 78 wt % siUca, added as diatomaceous earth or siUca gel, formed into rings, and calcined in the presence of sulfur dioxide or sulfur trioxide to convert a portion of the alkah metal salts into various pyrosulfates (81,82). 

---