Thermoplastics polyvinyl chloride

Figure 4-3. Comparison of ten-second modulus vs. temperature curves for three common thermoplastics polyvinyl chloride (PVC), polystyrene (PS) and polyethylene (PE).

Ferric acetylacetonate Polyurethane, thermoplastic Polyvinyl chloride Triethylene diamine... 

While natural plastics, such as cellulose and starch, are subject to strong attack by microorganisms, today s common plastics hardly serve as nutrients for microorganisms at all. Among thermoplastics, polyvinyl chloride and polyurethane containing plasticizers are in particular danger of microbial attack, see Section 5.6.4 [531]. 

The important thermoplastics used commercially are polyethylene, acrylonitrile butadiene styrene (ABS), polyvinyl chloride (PVC), cellulose acetate butyrate (CAB), vinylidene chloride (Saran), fluorocarbons (Teflon, Halar, Kel-F, Kynar), polycarbonates, polypropylene, nylons, and acetals (Delrin). Important thermosetting plasttcs are... 

Examples of thermoplastics are polyethylene, polyvinyl chloride, polystyrene, nylon, cellulose acetate, acetal, polycarbonate, polymethyl methacrylate and polypropylene. 

Polyvinyl chloride (PVC) is one of the most widely used thermoplastics. It can be extruded into sheets and film and blow molded into bottles. It is used in many common items such as garden hoses, shower curtains, irrigation pipes, and paint formulations. 

Currently, important TPE s include blends of semicrystalline thermoplastic polyolefins such as propylene copolymers, with ethylene-propylene terepolymer elastomer. Block copolymers of styrene with other monomers such as butadiene, isoprene, and ethylene or ethylene/propy-lene are the most widely used TPE s. Styrene-butadiene-styrene (SBS) accounted for 70% of global styrene block copolymers (SBC). Currently, global capacity of SBC is approximately 1.1 million tons. Polyurethane thermoplastic elastomers are relatively more expensive then other TPE s. However, they are noted for their flexibility, strength, toughness, and abrasion and chemical resistance. Blends of polyvinyl chloride with elastomers such as butyl are widely used in Japan. ... 

In terms of tonnage the bulk of plastics produced are thermoplastics, a group which includes polyethylene, polyvinyl chloride (p.v.c.), the nylons, polycarbonates and cellulose acetate. There is however a second class of materials, the thermosetting plastics. They are supplied by the manufacturer either as long-chain molecules, similar to a typical thermoplastic molecule or as rather small branched molecules. They are shaped and then subjected to either heat or chemical reaction, or both, in such a way that the molecules link one with another to form a cross-linked network (Fig. 18.6). As the molecules are now interconnected they can no longer slide extensively one past the other and the material has set, cured or cross linked. Plastics materials behaving in this way are spoken of as thermosetting plastics, a term which is now used to include those materials which can in fact cross link with suitable catalysts at room temperature. 

Amorphous thermoplastics These are made from polymers which have a sufficiently irregular molecular structure to prevent them from crystallising in any way. Examples of such materials are polystyrene, poly methyl methacrylate and polyvinyl chloride. 

Polyvinyl chloride (p.v.c.) P.V.C. is one of the two most important plastics in terms of tonnage and shows many properties typical of rigid amorphous thermoplastics. More individually, it softens at about 70°C, burns only with difficulty and is thermally unstable. To reduce this instability, stabilisers are invariably compounded into the polymer. 

Thermoplastics 1. Polyvinyl chloride (p.v.c.) (and other chlorinated thermoplastics)... 

Polyvinyl Chloride. (Chloroethene homopolymer, Chloroethylene polymer, PVC, Vybak, Geon, Breon, Welvic, Deckor, Vinacort, Ultron, Vinyl-ite, Koroseal, Marvinol). A synthetic thermoplastic polymer white powder or colorl granules ... 

The ductility of GRT-polyethylene blends drastically decreases at ground rubber concentration in excess of 5%. The inclusion of hnely ground nitrile rubber from waste printing rollers into polyvinyl chloride (PVC) caused an increase in the impact properties of the thermoplastic matrix [76]. Addition of rubber powder that is physically modihed by ultrasonic treatment leads to PP-waste ethylene-propylene-diene monomer (EPDM) powder blends with improved morphology and mechanical properties [77]. 

Thermoplastic materials, which soften with increasing temperature for example, polyvinyl chloride (PVC) and polyethylene. 

In this chapter, the big four thermoplastics are covered polyethylene, polypropylene, polyvinyl chloride, and polystyrene. Like most other thermoplastics, they are long-chain polymers that become soft when heated and can be molded under pressure. They are linear- or branch-chained and, except for some exotic copolymers, have little or no cross-linking. Technological advances continue. Research in copolymerization, catalysts, processing, blending, and fabricating continues even as you read this. 

Olefins or alkenes are defined as unsaturated aliphatic hydrocarbons. Ethylene and propylene are the main monomers for polyolefin foams, but dienes such as polyisoprene should also be included. The copolymers of ethylene and propylene (PP) will be included, but not polyvinyl chloride (PVC), which is usually treated as a separate polymer class. The majority of these foams have densities <100 kg m, and their microstructure consists of closed, polygonal cells with thin faces (Figure la). The review will not consider structural foam injection mouldings of PP, which have solid skins and cores of density in the range 400 to 700 kg m, and have distinct production methods and properties (456). The microstructure of these foams consists of isolated gas bubbles, often elongated by the flow of thermoplastic. However, elastomeric and microcellular foams of relative density in the range 0.3 to 0.5, which also have isolated spherical bubbles (Figure lb), will be included. The relative density of a foam is defined as the foam density divided by the polymer density. It is the inverse of the expansion ratio . 

Thermoplastic Polymers. Most thermoplastic polymers are used in high-volume, widely recognized applications, so they are often referred to as commodity plastics. (We will elaborate upon the distinction between a polymer and a plastic in Chapter 7, but for now we simply note that a plastic is a polymer that contains other additives and is usually identified by a variety of commercial trade names. There are numerous databases, both in books [1] and on the Internet [2], that can be used to identify the primary polymer components of most plastics. With a few notable exceptions, we will refer to most polymers by their generic chemical name.) The most common commodity thermoplastics are polyethylene (PE), polypropylene (PP), polyvinyl chloride (PVC) and polystyrene (PS). These thermoplastics all have in common the general repeat unit -(CHX-CH2)-, where -X is -H for PE, -CH3 for PP, -Cl for PVC, and a benzene ring for PS. When we discuss polymerization reactions in Chapter 3, we will see that all of these thermoplastics can be produced by the same type of reaction. 

There is every indication that the next several years will witness a continued rapid increase in the use of petroleum raw materials in the production of elastomers and plastics, and that the petroleum companies will become increasingly active, not only in providing the starting materials, but also in operating the chemical processes of converting them to the required monomers and polymers. The current increase in production of thermoplastic resins such as polystyrene, polyvinyl chloride, polyethylene, and acrylonitrile polymers is based on the development of widespread new applications at the consumer level, and the outlet for plastic materials in many of these uses is presently limited by the capacity to produce and process the resins rather than by consumer demand. 

The principal kinds of thermoplastic resins include (1) acrylonitrile-butadiene-styrene (ABS) resins (2) acetals (3) acrylics (4) cellulosics (5) chlorinated polyelliers (6) fluorocarbons, sucli as polytelra-fluorclliy lene (TFE), polychlorotrifluoroethylene (CTFE), and fluorinated ethylene propylene (FEP) (7) nylons (polyamides) (8) polycarbonates (9) poly elliylenes (including copolymers) (10) polypropylene (including copolymers) ( ll) polystyrenes and (12) vinyls (polyvinyl chloride). The principal kinds of thermosetting resins include (1) alkyds (2) allylics (3) die aminos (melamine and urea) (4) epoxies (5) phenolics (6) polyesters (7) silicones and (8) urethanes,... 

Plastisols are used for molding thermoplastic resins, chiefly polyvinyl chloride. See also Plasticizers. 

THERMOPLASTIC. A high polymer that softens when exposed to heat and returns to its original condition when cooled to room temperature. Natural substances that exhibit this behavior are crude rubber and a number of waxes however, the term is usually applied to synthetics such as polyvinyl chloride, nylons, fluorocarbons, linear polyethylene, polyurethane prepolymer, polystyrene, polypropylene, and cellulosic and acrylic resins. See also Plastics. 

Thermoplastics consist of long chains of molecules, in the case of PE these are unbranched. Many of these chains together form a tangle which is more difficult to unravel the more branched the chains are. The branches are like hooks which cause the molecules to catch. Under the influence of relatively small external forces chains and parts of chains can slide across each other. PE is for instance used to make containers, chemical tubing and blow-moulded bottles. Some other thermoplastics are polypropylene (crates), polyvinyl chloride PVC (pipes) and polystyrene (foam). 

PC PE PES PET PF PFA PI PMMA PP PPO PS PSO PTFE PTMT PU PVA PVAC PVC PVDC PVDF PVF TFE SAN SI TP TPX UF UHMWPE UPVC Polycarbonate Polyethylene Polyether sulfone Polyethylene terephthalate Phenol-formaldehyde Polyfluoro alkoxy Polyimide Polymethyl methacrylate Polypropylene Polyphenylene oxide Polystyrene Polysulfone Polytetrafluoroethylene Polytetramethylene terephthalate (thermoplastic polyester) Polyurethane Polyvinyl alcohol Polyvinyl acetate Polyvinyl chloride Polyvinyl idene chloride Polyvinylidene fluoride Polyvinyl fluoride Polytelrafluoroethylene Styrene-acrylonitrile Silicone Thermoplastic Elastomers Polymethylpentene Urea formaldehyde Ultrahigh-molecular-weight polyethylene Unplasticized polyvinyl chloride... 

The most common advanced composites are made of thermosetting resins, such as epoxy polymers (the most popular singlematrix material), polyesters, vinyl esters, polyurethanes, polyimids, cianamids, bismaleimides, silicones, and melamine. Some of the most widely used thermoplastic polymers are polyvinyl chloride (PVC), PPE (poly[phenylene ether]), polypropylene, PEEK (poly [etheretherketone]), and ABS (acrylonitrile-butadiene-styrene). The precise matrix selected for any given product depends primarily on the physical properties desired for that product. Each type of resin has its own characteristic thermal properties (such as melting point... 

---