Supported systems

SMITH, VAN LAAN Piping and Pipe Support Systems STOCK AI in Process Control... 

Although the type of production support systems required depend upon reservoir type the most common include ... 

BE-7120 Reliability based decision support system for the maintenance management of the underaround networks of utilities. Prof. T. Hadailacos Computer Tech. Instrtute Patras Uniwerirty... 

R. N. Prince, T. L. Dies, and W. J. O ReiUy, "Development of the Portable Environment Control System," Conference on Portable Fife Support Systems,... 

K. J. Dressier and R. N. Prince, "Lithium Peroxide for Portable Life Support System Atmospheric Regeneration," Conference on Portable Eife Support Systems, NASA-Ames Research Center, Moffett Field, Calif., Apr. 1969. 

For piping systems operating within at least 150°C above or below ambient temperature, heat loss or gain, respectively, from the piping to the support system should be evaluated, as well as local thermal stresses due to temperature differences between the pipe and its support attachment. Clamp-type supports iasulated from the piping, and extended support connections with the support members covered with iasulation at the support junction and for a distance beyond frequently are used for such systems. 

Artificial Hearts. Congestive heart failure (CHF) is a common cause of disabiHty and death. It is estimated that three to four million Americans suffer from this condition. Medical therapy in the form of inotropic agents, diuretics (qv), and vasofilators is commonly used to treat this disorder (see Cardiovascularagents). Cardiac transplantation has become the treatment of choice for medically intractable CHF. Although the results of heart transplantation are impressive, the number of patients who might benefit far exceeds the number of potential donors. Long-term circulatory support systems may become an alternative to transplantation (5). 

The cutting tool is an important component of the machining system. Consequendy, tool materials significantly affect machining operation productivity. Other elements include cutting conditions, tool geometry, and the characteristics of the work material, nature of parts produced, machine tool, and support system. 

Eig. 8. An ethylene oxide sterilisation vessel (autoclave) and supportive system. 

L. A. Gordon and G. E. Piuches, Improving Capital Budgeting A Dedsion Support System Approach, Addison-Wesley, Reading, Mass., 1984. 

FIG. 16-48 Adsorber vessel with graded support system. Reprinted with permission ofEPA. Refer ence EPA, Process Design Manual for Carbon Adsorption, U.S. En-oir. Protect. Agency., Cincinnati, 1973.)... 

Cross-contamination Mixing chemicals unintentionally, typically through the use of the same process equipment or support systems for concurrent or successive tolls. 

Below we discuss the thermal effects and the electrodynamic forces which may develop during a fault to decide on the correct size of the conductor and its supporting system. 

This dual seal has both the rotary units facing in the same direction. This type of seal is recommended for very high pressures. The support system, and thus the area benveen the two seals, would be pressurized at /2 the aetual seal chamber pressure inside the pump (Figure 13-19, next page). 

For example, if the application is actually 800 psi, you would pressurize the barrier tank support system and the area between the two seals at 400 psi. This way the inboard seal would seal 400 psi (800 - 400 = 400 psi) and the outboard seal would also seal 400 psi (400 - 0 = 400 psi). Each seal independently could seal maybe 500 psi, but not 800 psi. Together, the two seals in this tandem arrangement ean seal 800 psi and higher depending on the barrier tank pressure. 

The tandem dual seal is mostly mated to a pressurized barrier tank, or a pumping unit as the support system. Support systems are discussed later in this chapter. 

This facc-to-facc double seal is quite versatile (Figure 13-21). It is reeommended in a wide range of applieations depending on the piping arrangement of its support system. 

With its support system pressurized above the seal chamber pressure, this double seal functions well with toxic and dangerous liquids (like the back-to-back dual seal). If the support system is pressurized at / the seal chamber pressure, this seal can handle higher pressures where a single seal would fail. If the support system should be non pressurized... 

Double seals require some type of support system. The reason is simple. With two seals mounted onto the same shaft, one seal is the principal or primary seal and the other becomes the secondary or back up seal already installed. If the primary seal is performing its function and sealing the pumped liquid, the. secondary. seal would be running dry, overheat, burn and self-destruct. Then when the crucial moment comes, we won t have a second seal to assume the ftinctions, which was the original reason to consider a dual seal. 

So the support system serves to lubricate and cool the faces of the secondary seal while the first is performing its functions. The pressure applied to the support system governs the optimum life of the dual arrangement, and it also governs what happens when one of the two seals fails. 

There are three distinct support systems for double seals. They are often referred to as barrier tanks . The term barrier tank was initially applied to the thermal convection tank, although the term today refers to any of the three support systems. Each support system has different attributes. 

Figure 5-13. The Elliott TH expander is a single-stage hot gas expander with an axial inlet and vertical exhaust. The TH-line expanders range in horsepower from 4,000 to 50,000 and are of overhung rotor construction. The expander consists of four major components the inlet casing and its supports, the exhaust casing, the bearing housing and support system, and the rotor.

Critical speed is when the frequency of a periodic exciting frequency applied to the rotor-bearing support system corresponds to the natural frequency of the system. 

---