Sulphuric acid development

E. M, C hace has claboi-ated a method for the determination of citral depending on the fact that fuchsiuo-sulphurous acid develops a red coloration with aldchyde-g, the depth of which depends on the amount... 

SchifT s reagent A solution of rosaniline in water decolorized with sulphurous acid. Aliphatic aldehydes and aldose sugars give a magenta colour with this reagent with aromatic aldehydes and aliphatic ketones the colour develops more slowly aromatic ketones do not react. 

Dissolve a few drops of nitromethane in 10% sodium hydroxide solution. Add a few crystals of sodium nitrite and shake. Now add dilute sulphuric acid drop by drop. A brownish-red coloration develops, but fades again when an excess of acid is added. The sulphuric acid has thus liberated nitrous acid, which has in turn reacted with the nitromethane to give a nitrolic acid, the sodium salt of which is CH3NO2 + ONOH = CH(N02) N0H + HgO reddish-brown in colour, probably owing to mesomeric ions of the type ... 

Chakactkrisation of Unsaturatkd Aliphatic Hydrocarbons Unlike the saturated hydrocarbons, unsaturated aliphatic hydrocarbons are soluble in concentrated sulphuric acid and exhibit characteristic reactions with dUute potassium permanganate solution and with bromine. Nevertheless, no satisfactory derivatives have yet been developed for these hydrocarbons, and their characterisation must therefore be based upon a determination of their physical properties (boiling point, density and refractive index). The physical properties of a number of selected unsaturated hydrocarbons are collected in Table 111,11. 

Dissolve 1 g. of the secondary amine in 3-5 ml. of dilute hydrochloric acid or of alcohol (in the latter case, add 1 ml. of concentrated hydrochloric acid). Cool to about 5° and add 4-5 ml. of 10 per cent, sodium nitrite solution, and allow to stand for 5 minutes. Add 10 ml. of water, transfer to a small separatory funnel and extract the oil with about 20 ml. of ether. Wash the ethereal extract successively with water, dilute sodium hydroxide solution and water. Remove the ether on a previously warmed water bath no flames should be present in the vicinity. Apply Liebermann s nitroso reaction to the residual oil or solid thus. Place 1 drop or 0 01-0 02 g. of the nitroso compovmd in a dry test-tube, add 0 05 g. of phenol and warm together for 20 seconds cool, and add 1 ml. of concentrated sulphuric acid. An intense green (or greenish-blue) colouration will be developed, which changes to pale red upon pouring into 30-50 ml. of cold water the colour becomes deep blue or green upon adding excess of sodium hydroxide solution. 

This product is sufficiently pure for the preparation of phenylacetic acid and its ethyl ester, but it contains some benzyl tso-cyanide and usually develops an appreciable colour on standing. The following procedure removes the iso-cyanide and gives a stable water-white compound. Shake the once-distilled benzyl cyanide vigorously for 5 minutes with an equal volume of warm (60°) 60 per cent, sulphuric acid (prepared by adding 55 ml. of concentrated sulphuric acid to 100 ml. of water). Separate the benzyl cyanide, wash it with an equal volume of sa+urated sodium bicarbonate solution and then with an equal volume of half-saturated sodium chloride solution- Dry with anhydrous magnesium sulphate and distil under reduced pressure. The loss in washing is very small (compare n-Butyl Cyanide, Section 111,113, in which concentrated hydrochloric acid is employed). 

Girard s reagent P , C5H5NCH2C0NHNH2 C1. In a 1-htre threenecked flask, equipped as in the previous preparation, place 200 ml. of absolute ethyl alcohol, 63 g. (64 -5 ml.) of pure anhydrous pyridine and 98 - 5 g. (84 5 ml.) of ethyl chloroacetate. Heat the mixture under reflux for 2-3 hours until the formation of the quaternary salt is complete acidify a small test-portion with dilute sulphuric acid it should dissolve completely and no odour of ethyl chloroacetate should be apparent. Cool the mixture in ice and salt. Replace the thermometer by a dropping funnel, and add a solution of 40 g. of 100 per cent, hydrazine hydrate in 60 ml. of absolute ethanol all at once. A vigorous exothermic reaction soon develops and is accompanied by vigorous effervescence. The pro duct separates almost immediately. When cold, filter with suction, wash... 

The action of sulphuric acid alone upon acetone cyanohydrin affords a-methylacrylic acid. The methyl methacrylate polymers are the nearest approach to an organic glass so far developed, and are marketed as Perspex (sheet or rod) or Dialcon (powder) in Great Britain and as Plexiglass and Luciie in the U.S.A. They are readily depolymerised to the monomers upon distillation. The constitution of methyl methacrylate polymer has been given as ... 

The first nitration to be reported was that of beri2ene itself. Mitscher-lich in 1834 prepared nitrobenzene by treating benzene with fuming nitric acid. Not long afterwards the important method of effecting nitration with a mixture of nitric and sulphuric acids ( mixed acid ) was introduced, evidently in a patent by Mansfield the poor quality of early nitric acid was probably the reason why the method was developed. Since these beginnings, nitration has been the subject of continuous study. 

Table 9.7 contains recent data on the nitration of polychlorobenzenes in sulphuric acid. The data continue the development seen with the diehlorobenzenes. The introduetion of more substituents into these deactivated systems has a smaller effect than predicted. Whereas the -position in ehlorobenzene is four times less reactive than a position in benzene, the remaining position in pentachlorobenzene is about four times more reactive than a position in 1,3,4,5-tetraehlorobenzene. The chloro substituent thus activates nitration, a circumstance recalling the faet that o-chloronitrobenzene is more reactive than nitrobenzene. As can be seen from table 9.7, the additivity prineiple does not work very well with these compounds, underestimating the rate of reaction of pentachlorobenzene by a factor of nearly 250, though the failure is not so marked in the other cases, especially viewed in the circumstance of the wide range of reactivities covered. 

Japanese workers have developed fibres from poly(vinyl alcohol). The polymer is wet spun from warm water into a concentrated aqueous solution of sodium sulphate containing sulphuric acid and formaldehyde, the latter insolubilising the alcohol by formation of formal groups. 

A fuel cell is simply a device with two electrodes and an electrolyte for extracting power from the oxidation of a fuel without combustion, converting the power released directly into electricity. The fuel is usually hydrogen. The principle of a fuel cell was first demonstrated by Sir William Grove in London in 1839 with sulphuric acid and platinum gauze as an electrocatalyst, and thereafter there were very occasional attempts to develop the principle, not all of which were based on sound scientific principles , as one commentator put it. 

Atropine causes dilation of the pupil of the eye. A drop or two of an aqueous solution, containing 1 part in 130,000 parts of water, introduced into the eye of a cat is sufficient to produce this effect. When warmed with sulphuric acid and a small crystal of potassium dichromate, atropine develops a bitter almond odour. Evaporated to dryness on a water-bath with concentrated nitric acid, it gives a residue which becomes violet on adding a drop of sodium hydroxide solution in alcohol (Vitali s test). With a solution of mercuric chloride atropine gives a yellow to red precipitate of mercuric oxide. 

Probably the most useful characteristic of the high-silicon irons is their ability to withstand sulphuric acid at all temperatures and concentrations. The maximum rate of corrosion which can develop has been reported to be 0-482mm/y in 30% sulphuric acid at boiling point", and this falls to a minimum rate of 0-025 mm/y when the acid concentration exceeds 60% and the temperature is at boiling point (Fig. 3.64). The former Ministry of Supply... 

Although the first industrial application of anodic protection was as recent as 1954, it is now widely used, particularly in the USA and USSR. This has been made possible by the recent development of equipment capable of the control of precise potentials at high current outputs. It has been applied to protect mild-steel vessels containing sulphuric acid as large as 49 m in diameter and 15 m high, and commercial equipment is available for use with tanks of capacities from 38 000 to 7 600000 litre . A properly designed anodic-protection system has been shown to be both effective and economically viable, but care must be taken to avoid power failure or the formation of local active-passive cells which lead to the breakdown of passivity and intense corrosion. 

Tetrachromate electrolytes The alkaline tetrachromate baths are used to a small extent chiefly for the direct chromium plating of zinc die-castings, brass or aluminium, since the solutions do not attack these metals . The original bath was developed by Bornhauser (German Pat. 608 757) and contained 300 g/1 of chromic acid, 60g/l of sodium hydroxide, 0-6-0-8g/l of sulphuric acid and 1 ml/l of alcohol. 

Although there have been few changes in the basic anodising practices, and sulphuric acid is the electrolyte used in most plants, there have been many developments in the pretreatment, colouring and sealing processes associated with anodising. 

The most commonly used chromate passivation process is the Cronak process developed by the New Jersey Zinc Co. in 1936, in which the parts are immersed for 5-10 s in a solution containing 182 g/1 sodium dichromate and 6ml/l sulphuric acid. A golden irridescent film is formed on the zinc or cadmium surface. Many variants (all fairly acidic) have been developed subsequently all are based on dichromate (or chromic acid) with one or more of the following sulphuric acid, hydrochloric acid (or sodium chloride), nitric acid (or nitrate), phosphoric acid, formic acid and acetic acid. A survey by Biestek shows that several of these variants are as good as the Cronak process, although none is superior. 

---