Steel atmospheric corrosion

In atmospheric exposure 18% Ni maraging steel corrodes in a uniform manner , and becomes completely rust covered. Pit depths tend to be more shallow than for the low-alloy high-strength steels. Atmospheric corrosion rates in industrial (Bayonne, New Jersey) and marine (Kute Beach, North Carolina) atmospheres are compared with those for low-alloy steel in Figs. 3.29, 3.30 and 3.31. The corrosion rates drop substantially after the first year or two and in all cases the rates for maraging steel are about half the corrosion rate for HY80 and AISI 4340 steels. 

Tin—Nickel. AHoy deposits having 65% fin have been commercially plated siace about 1951 (135). The 65% fin alloy exhibits good resistance to chemical attack, staining, and atmospheric corrosion, especially when plated copper or bron2e undercoats are used. This alloy has a low coefficient of friction. Deposits are solderable, hard (650—710 HV ), act as etch resists, and find use ia pfinted circuit boards, watch parts, and as a substitute for chromium ia some apphcafions. The rose-pink color of 65% fin is attractive. In marine exposure, tin—nickel is about equal to nickel—chromium deposits, but has been found to be superior ia some iadustfial exposure sites. Chromium topcoats iacrease the protection further. Tia-nickel deposits are bfitde and difficult to strip from steel. Temperature of deposits should be kept below 300°C. 

It is agreed generally that the characteristics of the rust films that form on steels determine their resistance to atmospheric corrosion. The rust films that form on low-aUoy steels are more protec tive than those that form on unalloyed steel. 

With some important exceptions, gray-iron castings generally have corrosion resistance similar to that of carbon steel. They do resist atmospheric corrosion as well as attack by natural or neutral waters and neutral soils. However, dilute acids and acid-salt solutions will attack this material. 

Mild steel, also low-alloy irons and steels 0 3 0 3 < 400 1 < 750 Wronglit, cast Good Good 67 6.7 Higli strengths obtainable by alloying, also improved atmospheric corrosion resistance. See ASTM specifications for particular grade... 

Zinc diffusion is used for protection against atmospheric corrosion. Aluminum diffusion is used to improve the oxidation resistance of low-carbon steels. 

BS2569 Sprayed Metal Coatings. Part 1 Protection of Iron and Steel by Aluminum and Zinc Against Atmospheric Corrosion. ... 

However, the object of this section is to outline the principles which govern atmospheric corrosion, and the emphasis is placed on metals whose atmospheric corrosion is of economic importance. These include iron and steel, zinc, copper, lead, aluminium and chromium. 

However, in this section emphasis is placed upon damp and wet atmospheric corrosion which are characterised by the presence of a thin, invisible film of electrolyte solution on the metal surface (damp type) or by visible deposits of dew, rain, sea-spray, etc. (wet type). In these categories may be placed the rusting of iron and steel (both types involved), white rusting of zinc (wet type) and the formation of patinae on copper and its alloys (both types). 

Sulphur oxides These (SO2 is the most frequently encountered oxide) are powerful stimulators of atmospheric corrosion, and for steel and particularly zinc the correlation between the level of SO2 pollution and corrosion rates is good However, in severe marine environments, notably in the case of zinc, the chloride contamination may have a higher correlation coefficient than SO2. 

Table 3.4 Effect of the surface condition at the time of exposure on the atmospheric corrosion of mild steel (BISRA) (5 years outdoor exposure at Sheffield)...

It should be made clear that all the rates of rusting in the atmosphere just quoted, relate to average general penetration and take no account of pitting. Serious pitting of steel exposed to atmospheric corrosion is uncomm.on on simple test plates, but it may be necessary to allow for this in some practical cases, where local attack may be occasioned by faulty design and other factors. 

Table 3.31 Resistance of Fe-36 Ni and mild steel to corrosion in marine atmospheres ...

The reason for the use of zinc as a power-impressed rather than a sacrificial anode is that the high concrete resistivity limits the current output, and a higher driving voltage than that provided by the e.m.f. between zinc and steel in concrete is used to provide the necessary current output. No cementitious overlay is required, although it may be advisable to paint the top surface of the sprayed zinc to prevent atmospheric corrosion of the zinc anode. 

In principle, cathodic protection can be used for a variety of applications where a metal is immersed in an aqueous solution of an electrolyte, which can range from relatively pure water to soils and to dilute solutions of acids. Whether the method is applicable will depend on many factors and, in particular, economics — protection of steel immersed in a highly acid solution is theoretically feasible but too costly to be practicable. It should be emphasised that as the method is electrochemical both the structure to be protected and the anode used for protection must be in both metallic and electrolytic contact. Cathodic protection cannot therefore be applied for controlling atmospheric corrosion, since it is not feasible to immerse an anode in a thin condensed film of moisture or in droplets of rain water. 

Fig. 12.9 Corrosion resistance of tin-nickel electrodeposit impaired by pseudomorphic porosity originating on cold-rolled steel surface (left). Panel on right has had the shattered grain surface removed by chemical polishing (0-125 iim removed). Coating thickness 15 iim-, panels exposed 6 months to marine atmospheric corrosion (Hayling Island)...

Paint for structural steelwork is required mainly to prevent corrosion in the presence of moisture. In an industrial atmosphere this moisture may carry acids and in a marine atmosphere this moisture may carry chlorides. Paint is therefore required to prevent contact between steel and corrosive electrolytes, and to stifle corrosion, should it arise as a result of mechanical damage or breakdown of the coating through age and exposure. 

The relative susceptibility of metals to atmospheric corrosion varies widely with the type of contaminant, e.g. zinc and cadmium, two metals that are used for the protection of steel in exposed environments, are both rapidly attacked by organic acidson the other hand, aluminium alloys resist attack by organic acids but may be rapidly corroded by chlorides, especially at crevices or areas of contact. 

Copson has described in considerable detail the several factors that require attention in studying atmospheric corrosion, particularly of steels. 

Practice for making and using U-bend stress corrosion test specimens Recommended practice for laboratory immersion corrosion testing of metals Method for vibratory cavitation erosion test Practice for recording data from atmospheric corrosion tests of metallic-coated steel specimens... 

Guide for estimating the atmospheric corrosion resistance of low-alloy steels Practice for calculation of corrosion rates and related information from electrochemical measurements... 

A wide range of paints and other organic coatings is used for the protection of mild steel structures. Paints are used mainly for protection from atmospheric corrosion. Special chemically resistant paints have been developed for use on chemical process equipment. Chlorinated rubber paints and epoxy-based paints are used. In the application of paints and other coatings, good surface preparation is essential to ensure good adhesion of the paint film or coating. 

---