Damping types

However, in this section emphasis is placed upon damp and wet atmospheric corrosion which are characterised by the presence of a thin, invisible film of electrolyte solution on the metal surface (damp type) or by visible deposits of dew, rain, sea-spray, etc. (wet type). In these categories may be placed the rusting of iron and steel (both types involved), white rusting of zinc (wet type) and the formation of patinae on copper and its alloys (both types). 

Tliere is another type of application where the damping effect of plastic structures can be used to advantage. It has a long although not obvious history. The early airplanes used doped fabric as the covering for wings and other aerodynamic surfaces. The dope was cellulose nitrate and later cellulose acetate that is a damping type of plastic. Conse-... 

Unless I is exceptionally large, or the power density is exceptionally high, jS/2Z > Q, and the motion possesses no oscillatory character. For reactors of this strongly over-damped type, the frequency Q becomes meaningless, and its appearance in the equations is only a disguise for the parameter... 

The wash primer is a special type of vinyl coating. This material contains a poly(vinyl butyral) resin, zinc chromate, and phosphoric acid in an alcohol-water solvent. The coating is so thin it is HteraUy washed onto a freshly blasted steel surface, where it passivates the metal surface by converting it to a thin iron phosphate-chromate coating. The alcohol solvent makes it possible to apply the coating over damp surfaces. The coating forms the first coat of... 

Butyl-type polymers exhibit high damping, and the viscous part of the dynamic modulus is uniquely broad as a function of frequency or temperature. Molded mbber parts for damping and shock absorption find wide appHcation in automotive suspension bumpers, auto exhaust hangers, and body mounts. 

Undei damped behavior. Measurement devices with mechanical components often have a natural harmonic and can exhibit underdamped behavior. The displacer type of level measurement device is capable of such behavior. 

The large variety of displacement-type flmd-transport devices makes it difficult to list characteristics common to each. However, for most types it is correct to state that (1) they are adaptable to high-pressure operation, (2) the flow rate through the pump is variable (auxiliary damping systems may be employed to reduce the magnitude of pressure pulsation and flow variation), (3) mechanical considerations limit maximum throughputs, and (4) the devices are capable of efficient performance at extremely low-volume throughput rates. 

Equipment should be supported in such a way that it will not rest in pools of hquid or on damp insulating material. Porous insulation should be weatherproofed or otherwise protected from moisture and spills to avoid contact of the wet material with the equipment. Specifications should be sufficiently comprehensive to ensure that the desired composition or type of material will be used and the right condition of heat treatment and surface finish will be provided. Inspection during fabrication and prior to acceptance is desirable. 

An object can acquire the following four types of damping characteristics ... 

Since discrete quantities are trapped and transferred, the delivery pressure and flow varies, as shown in Figure 32.21, which also illustrates how increasing the number of cylinders in a reciprocating pump reduces fluctuations. In the case of lobe and gear pumps the fluctuations are minimized by speed of rotation and increasing tooth number, but where, for control or process reasons, the ripple in pressure is still excessive, means of damping pulsations has to be fitted. Often a damper to cope with this and pressure pulses due to valve closure is fitted, and two types are shown in Figure 32.22. 

Determining if two or more compressors should have separate or single foundations depends on the compressor type. A combined foundation is recommended for reciprocating units since the forces from one unit usually will partially balance out the forces from the others. In addition, the greater mass and surface area in contact with the ground damps foundation movement and provides greater stability. 

Light, sandy, well-drained soil of high electrical resistivity is low in corrosivity and coated steel or bare stainless steels can be employed. It is unlikely that the whole pipe run would be in the same type of soil. In heavier or damp soils, or where the quality of back filling cannot be guaranteed, there are two major corrosion risks. Steel, copper alloys and most stainless steels are susceptible to sulfide attack brought about by the action of sulfate-reducing bacteria in the soil. SRB are ubiquitous but thrive particularly well in the anaerobic conditions which persist in compacted soil, especially clay. The mechanism of corrosion where SRB are involved is described in Section... 

Tannin-containing woods also darken with ammonia, a process which is usefully employed in darkening oak furniture by fuming . Ammonia stains can originate from animal glue, amino-type adhesives and concrete additive sources, particularly where damp conditions exist. 

---