Speed-current tests

Speed-torqtte and speed-current tests may be carried out by the following methods ... 

It is therefore necessary to take precautions during the test to avoid a excessive temperature rise and consequent damage to the windings. For wound rotor motors, speed-torque and speed-current tests may be taken between synchronous speed and the speed at which the maximum torque occurs. 

Test for speed-torque and speed-current curves 11/257... 

From a practical point of view, there are several additional criteria that the ideal test should meet. Alternatives to current in vivo test systems basically should be designed to evaluate the observed toxic response in a manner as closely predictive of the outcome of interest in humans as possible. In addition, the test should be fast enough so that the turnaround time for a given test chemical is reasonable for the intended purpose (very rapid for a screen and timely for a definitive test). The speed of the test and the ability to conduct tests on several chemicals simultaneously will determine the overall productivity. The test should be inexpensive so that it is economically competitive with current testing practices. Finally, the technology should be easily transferred from one laboratory to another without excessive capital investment (relative to the value of the test performed) or the need for special skills for test implementation. 

Tests were done on real data containing approx. 32(XX) nontrivial images. Of these approx. 25% were classified by the rule-based system and another 25% by the CBR system. The reliability was high - of 330 defects present in the data only two were classified as non-defects. We are currently working on further improving the recognition ratio and increasing the speed of the system. 

The Nametre Rotary B rotational viscometer measures torque in terms of the current needed to drive the d-c motor at a given speed while a material is under test. The standard sensors are coaxial cylinders or Brookfield disk-type spindles, but a cone—plate system is also available. The viscosity range for the coaxial cylinder sensors is 5 to 5 x 1(T mPa-s, and the maximum shear rate is 200. ... 

Because of its high toughness and good thermal shock resistance, test results indicate the possibility of using square-, triangular-, and diamond-shaped tools of SiAlON for machining superaHoys in the intermediate speed range (ca 150 m /min) where only round tools are used currently with other ceramics. 

The results processor computes the test results from the raw data furnished by the AP and coUates these results together with the demographic patient data into test reports. Test results falling outside normal limits are flagged on the report to speed up the diagnosis process. These data managers can also store thousands of patient reports in their current memory. Some of the more sophisticated systems also store the actual reaction curves used to determine the test results. 

This is a very useful nomogram to determine the performance of a motor with the help of only no-load and short-circuit test results. In slip-ring motors, it also helps to determine the external resistance required in the rotor circuit to control the speed of the motor and achieve the desired operating performance. Slip-ring motors are discussed in Chapter 5. The concept behind this nomogram is that the locus of the rotor and the stator currents is a circle. Consider the equivalent circuit of an induction motor as shown in Figure 1.15, where... 

When enrichment episodes occur in the real world, but not in the laboratory under federal certification tests, real-world emissions are significantly higher than predicted. Further complicating emissions prediction is that aggressive driver behavior and complex traffic flow characteristics play a large role in enrichment occurrence. Current vehicle activity simulation models can predict average speeds and traffic volumes very well, but poorly predict the hard-accel-eration events that lead to enrichment. 

Eng used the galvanostatic deposition of monodisperse polystyrene particles onto a RCE from an acidic copper sulfate to test her theoretical predictions. The particle deposition was found to increase with current density. The increase was greatest at a rotation speed of 615 rpm, and lower at higher and lower rotation speeds. The effect of current density on particle deposition is predicted using her MEIPET boundary conditions but the effect of the rotation speed cannot be explained. 

The only in vitro studies fully validated and included in the EU test methods (a.2) are for skin corrosivity and phototoxicity, but efforts are underway to speed up validation for other endpoints. An original aim was that there would be no animal studies for the basic level of registration, but as there is currently no suitable in vitro test for skin sensitisation, the mouse local lymph node assay is included in Annex V of the Regulation (Table 9). The in vitro tests for skin and eye irritation are not fully validated, so as a compromise they are accepted for registration at up to 10 tonnes per annum (i.e., they are in Annex V), but if the results are negative they have to be confirmed by a standard animal test at 10 tonnes per annum (i.e., the Annex VI data, as shown in Table 10). 

---