Sodium conduction, determination

The energy of the bottom of the sodium conduction band, denoted by 2, is determined by imposing the bonding boundary condition across the Wigner-Seitz sphere of radius, Kws, namely... 

Capillary electrophoresis Capillary electrophoresis (CE) is used to analyze sodium, potassium, calcium, and magnesium in water samples. The detection is conducted by reverse absorbance measurements. Sufficient separation of the four cations is established with an electrolyte solution of 5 mM imidazole/6.5 mM a-hydroxyisobutyric acid/2 mM 18-crown-6 ether of pEI 4.1 [42]. CE with a contactless conductometric detector is used to determine small anions and cations in water samples from different sources. 2-(N-Morpholino)ethanesulfonic acid/histidine-based (Mes/Elis) electrolytes are used for direct conductivity detection of anions and cations, while ammonium acetate is used for indirect conductivity determination of alkylammonium salts. Eor the simultaneous separation procedure, involving dual-opposite end injection, an electrolyte consisting of 20 mM Mes/EIis, 1.5 mM 18-crown-6 and 20 mM cetyltri-methylammonium bromide provides baseline separation of 13 anions and cations in less than 6 min [43]. Also CE with a capacitively coupled... 

Figure 7. Estimates of the sodium-conductance activation relaxation time, rm, and inactivation relaxation time, rh, from fits of eqs 2, 3, and 5 YK(jf) = 0 to admittance determinations at various membrane voltages, similar to those shown in Figure 6. Filled triangles are from fits of the average (AVE) of the real and imaginary parts of eight separate, successive admittance determinations at each voltage. Open circles and squares are from fits of 1 standard deviation added to ( + SD) or subtracted from ( — SD) the real and imaginary parts of the AVE admittance. Axon 87-37 internally perfused with the perfusate described in text and externally perfused with ASW at 9 °C.

The importance of these studies lies in the determination of site density. If site density is known with accuracy, together with a knowledge of the maximal sodium conductance, then the conductance of individual ionic channels can be estimated. The first part of this review was concerned with the alternatives of carrier-mediated, or pore-mediated transfer of ions across artificial membranes. Direct estimates of channel conductances in biological membranes allow tentative conclusions to be drawn concerning mechanisms in biological membranea. 

It is frequently advisable in the routine examination of an ester, and before any derivatives are considered, to determine the saponification equivalent of the ester. In order to ensure that complete hydrolysis takes place in a comparatively short time, the quantitative saponi fication is conducted with a standardised alcoholic solution of caustic alkali—preferably potassium hydroxide since the potassium salts of organic acids are usuaUy more soluble than the sodium salts. A knowledge of the b.p. and the saponification equivalent of the unknown ester would provide the basis for a fairly accurate approximation of the size of the ester molecule. It must, however, be borne in mind that certain structures may effect the values of the equivalent thus aliphatic halo genated esters may consume alkali because of hydrolysis of part of the halogen during the determination, nitro esters may be reduced by the alkaline hydrolysis medium, etc. 

In this experiment phosphate is determined by singlecolumn, or nonsuppressed, ion chromatography using an anionic column and a conductivity detector. The mobile phase is a mixture of n-butanol, acetonitrile, and water (containing sodium gluconate, boric acid, and sodium tetraborate). 

Ash is a measure of residual sodium acetate. A simple method consists of dissolving the PVA in water, diluting to a known concentration of about 0.5 wt %, and measuring the electrical conductivity of the solution at 30°C. The amount of sodium acetate is estabUshed by comparing the result to a cahbration curve. A more lengthy method involves the extraction of the PVA with methanol using a Soxhlet extractor. The methanol is evaporated and water is added. The solution is titrated using hydrochloric acid in order to determine the amount of sodium acetate. 

Furthermore, the electrical conductivities of liquid Na-Sn alloys for the five compositions are determined with the Kubo-Greenwood scheme, using the trajectories from our ab initio MD simulations. The calculated values reproduce the measured strong variation of the conductivity with the Na (or Sn) concentration very well. The small (semimetallic) conductivity of the alloys with nearly equimolar composition can be explained by the position of the Fermi energy between the occupied sp-band of tin and the sp-band of sodium. 

Because sodium, which is liquid between about 100°C and 881°C, has excellent properties as a heat-transfer medium, with a viscosity comparable with that of water and superior heat conductivity , much attention has been paid to liquid sodium corrosion testing of metal and alloys. Indeed, ASTM have issued a Standard Practice which can be used for determination... 

The conductivity of sodium dodecyl sulfate in aqueous solution and in sodium chloride solutions was studied by Williams et al. [98] to determine the CMC. Goddard and Benson [146] studied the electrical conductivity of aqueous solutions of sodium octyl, decyl, and dodecyl sulfates over concentration ranges about the respective CMC and at temperatures from 10°C to 55°C. Figure 14 shows the results obtained by Goddard and Benson for the specific conductivity of sodium dodecyl sulfate and Table 25 shows the coefficients a and p of the linear equation of the specific conductivity, in mho/cm, vs. the molality of the solution at 25°C. Micellization parameters have been studied in detail from conductivity data in a recent work of Shanks and Franses [147]. 

Free-radical copolymerization of vinyl acetate with various vinyl siloxane monomers was described 345). Reactions were conducted in benzene at 60 °C using AIBN as the initiator. Reactivity ratios were determined. Selective hydrolysis of the vinyl acetate units in the copolymer backbone was achieved using an aqueous sodium hy-droxide/THF mixture. The siloxane content and degree of hydrolysis were determined by H-NMR. 

The ionic conductivity of complexes of the polymer VIII n=3 with potassium, sodium and cesium thiocyanates were also determined. The conductivity of the polymer complexed with CsSCN is in the order of 10" S cm" at 30 °C, and lO- Scm-i at 90 °C [616]. 

Next, a series of runs was conducted to determine the effect of various alkali metal hydroxide additions along with the sponge nickel catalyst. The 50 wt. % sodium hydroxide and 50 wt. % potassium hydroxide caustic solution used in the initial test was replaced with an aqueous solution of the alkali metal hydroxide at the level indicated in Table 2. After the reaction number of cycles indicated in Table 2, a sample was removed for analysis. The conditions and results are shown in Table 2. The results reported in Table 2 show the level of 2° Amine in the product from the final cycle. The level of NPA in all of the mns was comparable to the level observed in the initial test. No significant levels of other impurities were detected. 

To establish the well drainage boundaries and fluid flow patterns within the TFSA-waterflood pilot, an interwell chemical tracer study was conducted. Sodium thiocyanate was selected as the tracer on the basis of its low adsorption characteristics on reservoir rocks (36-38), its low and constant background concentration (0.9 mg/kg) in produced fluids and its ease and accuracy of analysis(39). On July 8, 1986, 500 lb (227 kg) of sodium thiocyanate dissolved in 500 gal (1.89 m3> of injection brine (76700 mg/kg of thiocyanate ion) were injected into Well TU-120. For the next five months, samples of produced fluids were obtained three times per week from each production well. The thiocyanate concentration in the produced brine samples were analyzed in duplicate by the standard ferric nitrate method(39) and in all cases, the precision of the thiocyanate determinations were within 0.3 mg/kg. The concentration of the ion in the produced brine returned to background levels when the sampling and analysis was concluded. 

Favaro and Fiorani [34] used an electrode, prepared by doping conductive C cement with 5% cobalt phthalocyanine, in LC systems to detect the pharmaceutical thiols, captopril, thiopronine, and penicillamine. FIA determinations were performed with pH 2 phosphate buffer as the carrier stream (1 mL/min), an injection volume of 20 pL, and an applied potential of 0.6 V versus Ag/AgCl (stainless steel counter electrode). Calibration curves were developed for 5-100 pM of each analyte, and the dynamic linear range was up to approximately 20 pM. The detection limits were 76, 73, and 88 nM for captopril, thiopronine, and penicillamine, respectively. LC determinations were performed using a 5-pm Bio-Sil C18 HL 90-5S column (15 cm x 4.6 mm i.d.) with 1 mM sodium 1-octanesulfonate in 0.01 M phosphate buffer/acetonitrile as the mobile phase (1 mL/min) and gradient elution from 9 1 (held for 5 min) to 7 3 (held for 10 min) in 5 min. The working electrode was maintained at 0.6 V versus Ag/AgCl, and the injection volume was 20 pL. For thiopronine, penicillamine, and captopril, the retention times were 3.1, 5.0, and 11.3 min, and the detection limits were 0.71, 1.0, and 2.5 pM, respectively. 

---