Electrical safety hazards

Occupational Safety and Health Administration, OSHA Quick Facts Laboratory Safety Electrical Hazards, https //www.osha.gov/ Publications/laboratory/OSHAquickfacts-lab-safety-electrical-hazards. pdf, (accessed Dec 2014). 

Capp, B. and Widginton, D.W., "The Intrinsic Safety of Resistive Circuits", 2nd International Conference on Electrical Safety in Hazardous Environments, 9-11 Dec 1975, pages 43-47 Electrical Equipment for Hazardous Locations, Underwriters Laboratories, Inc., Northbrook, IL... 

Redding, R.J., "The Use of Solid State Circuitry Within Hazardous Areas", 3rd International Conference on Electrical Safety in Hazardous Environments, 1-3 Dec 1982, pages 219-233 Weatherhead, D., "Intrinsic Safety", Measurement and Control, Vol 10 No. 9, Sept 1977, pages 341-349... 

The overall intent of electrical area classification is to provide for safety of personnel and equipment. This is achieved by the elimination of electrical ignition sources near combustible gases or vapors that could explode or bum. The specific reasons for classifying facilities into electrical hazardous areas typically are ... 

Magision, E. C. Calder, W., Electrical Safety in Hazardous Locations. Instrument Society of America (ISA), Durham, NC, 1993. 

Underwriters Laboratories Inc. (UL), UL 674, Safety Electric Motors and Generators for Use in Division 1 Hazardous (Classified) Locations, Third Edition, UL, Northbrook, IL, 1994. 

A written safety program that includes the following topics new employee safety orientation, safety training, hazard communication, emergency action plan, fall protection, scaffolding, heat stress, personal protective equipment, electrical, first aid, and bloodborne pathogens. 

Chemical safety is inherently linked to other safety issues including laboratory procedures, personal protectives, equipment, electrical safety, and hazardous waste disposal. 

Chemical safety is inherently linked to other safety issues, including laboratory procedures, personal protective equipment, electrical safety, fire safety, and hazardous waste disposal. Specific chemical substances, uses, and possible health effects are discussed in different chapters of this book. The responsibility of workers as well... 

Electric heating elements can be sealed within aluminum blocks to provide a more uniform heat distribution and a protective measure of safety in hazardous, explosive environments. Cooling channels can also be designed into the aluminum blocks to provide external cooling for the vessel. 

A motivational look at the non-chemical hazards often encountered by hazardous waste workers. Recognizing dangerous situations, avoiding safety hazards (slips, trips, falls, electrical hazards, natural hazards, oxygen deficiency, heat stress), and special precautions for limited mobility and communication when wearing personal protective equipment. Pari of eight-volume series, Working in the Hazard Zone. ... 

P. A. Stewart and F. Latham, Seeing to do the right thing. Electrical safety in hazardous environments. lEE Conference 1 to 3 December 1982. Conference Publication No. 218, pages 80 to 86. IEEE Savoy Place, London, WC2 OBL ISBN 0 852-96267-3... 

General safety hazards, such as but not limited to, electrical hazards, powered equipment hazards, motor vehicle hazards, walking- and working-surface hazards, excavation hazards, and hazards associated with working in hot and cold temperature extremes. 

Electrical Hazard, U.S. Department of the Interior, National Mine Health and Safety Academy Safety Manual No. 9. 

Electrical safety is not limited only to products covered by the Low-Voltage Directive (LVD). According to the Machinery Directive, machine designers must also be aware of electrical safety since machines pose electrical hazards and they utilize numerous electrical components and subassemblies. The Low-Voltage Directive, General Product Safety Directive, and Machinery Directive mandate a product s conformity with the relevant electrical, mechanical, component, and other safety standards. To ensure that machinery electrical hazards are addressed by machine manufacturers, EN 60204-1/IEC 204-1 (Electrical Equipment of Machines) was published in both the Low-Voltage and Machinery directives, and, therefore, electrical requirements must also be applied to machinery. EN 60204-1 is a generic safety standard (type B) used in conjunction with the relevant machine safety standards (type C). 

Voltage and Shock Hazards. Inside the cell room, it is a practical necessity for operators to come into contact with live parts. Since some of the usual safety measures against electrical hazards do not apply, special codes of practice have been formulated. 

The practices described in Chapter 8 are designed to overcome electrical hazards. Air being an excellent insulator, clearances between live equipment and potential grounds provide safety. 

At construction sites the most common electrical hazard is the grovmd fault electrical shock. A ground fault occurs when a hot electrical wire contacts a grounded enclosvu-e. In most situations, the fault will trip a circuit breaker or blow a fuse. However, if a break in the ground wire occurs, the worker would no longer be protected, unless a secondary safety measure is available. 

---