Reactor porous

Porous metallic structures have been used for electrocatalysis (Chen and Lasia, 1991 Kallenberg et al., 2007). Porous electrodes are made with conductive materials that can degrade under high temperatures at high anodic potential conditions. This last problem is of less importance for fuel cell anodes, which operate at relatively low potentials, but it can be of importance for electrochemical reactors. Porous column electrodes prepared by packing a conductive material (carbon fiber, metal shot) forming a bar are frequently used. Continuous-flow column electrolytic procedures can provide high efficiencies for electrosynthesis or removal of pollutants in industrial situations. Theoretical analysis for the electrodeposition of metals on porous solids has been provided by Masliy et al. (2008). 

Catalytic gas-phase reactions play an important role in many bulk chemical processes, such as in the production of methanol, ammonia, sulfuric acid, and nitric acid. In most processes, the effective area of the catalyst is critically important. Since these reactions take place at surfaces through processes of adsorption and desorption, any alteration of surface area naturally causes a change in the rate of reaction. Industrial catalysts are usually supported on porous materials, since this results in a much larger active area per unit of reactor volume. 

Caustic Soda. Diaphragm cell caustic is commercially purified by the DH process or the ammonia extraction method offered by PPG and OxyTech (see Fig. 38), essentially involving Hquid—Hquid extraction to reduce the salt and sodium chlorate content (86). Thus 50% caustic comes in contact with ammonia in a countercurrent fashion at 60°C and up to 2500 kPa (25 atm) pressure, the Hquid NH absorbing salt, chlorate, carbonate, water, and some caustic. The overflow from the reactor is stripped of NH, which is then concentrated and returned to the extraction process. The product, about 62% NaOH and devoid of impurities, is stripped free of NH, which is concentrated and recirculated. MetaUic impurities can be reduced to low concentrations by electrolysis employing porous cathodes. The caustic is then freed of Fe, Ni, Pb, and Cu ions, which are deposited on the cathode. 

The problems of monomer recovery, reaction medium viscosity, and control of reaction heat are effectively dealt with by the process design of Montedison Fibre (53). This process produces polymer of exceptionally high density, so although the polymer is stiU swollen with monomer, the medium viscosity remains low because the amount of monomer absorbed in the porous areas of the polymer particles is greatly reduced. The process is carried out in a CSTR with a residence time, such that the product k jd x. Q is greater than or equal to 1. is the initiator decomposition rate constant. This condition controls the autocatalytic nature of the reaction because the catalyst and residence time combination assures that the catalyst is almost totally expended in the reactor. 

The prepolymer is separated from the water by spray drying and then formed into cylindrical pellets of uniform size (159). At this point additives can be added to the porous pellets from solution or suspension. These pellets are then placed in a soHd-phase condensation reactor where they are heated to 260°C for up to 4 h under nitrogen, with a small amount of water added. The pressure is maintained close to atmospheric pressure. At the end, x > n. 

Among continuous reactors, the dominant system used to produce parasubstituted alkylphenols is a fixed-bed reactor holding a soHd acid catalyst. Figure 3 shows an example of this type of reactor. The phenol and alkene are premixed and heated or cooled to the desired feed temperature. This mix is fed to the reactor where it contacts the porous soHd, acid-impregnated catalyst. A key design consideration for this type of reactor is the removal of the heat of reaction. 

Hydrides. Zirconium hydride [7704-99-6] in powder form was produced by the reduction of zirconium oxide with calcium hydride in a bomb reactor. However, the workup was hazardous and many fires and explosions occurred when the calcium oxide was dissolved with hydrochloric acid to recover the hydride powder. With the ready availabiHty of zirconium metal via the KroU process, zirconium hydride can be obtained by exothermic absorption of hydrogen by pure zirconium, usually highly porous sponge. The heat of formation is 167.4 J / mol (40 kcal/mol) hydrogen absorbed. 

Bosch and co-workers devised laboratory reactors to operate at high pressure and temperature in a recycle mode. These test reactors had the essential characteristics of potential industrial reactors and were used by Mittasch and co-workers to screen some 20,000 samples as candidate catalysts. The results led to the identification of an iron-containing mineral that is similar to today s industrial catalysts. The researchers recognized the need for porous catalytic materials and materials with more than one component, today identified as the support, the catalyticaHy active component, and the promoter. Today s technology for catalyst testing has become more efficient because much of the test equipment is automated, and the analysis of products and catalysts is much faster and more accurate. 

Oxychlorination of Ethylene to Dichloroethane. Ethylene (qv) is converted to dichloroethane in very high yield in fixed-bed, multitubular reactors and fluid-bed reactors by reaction with oxygen and hydrogen chloride over potassium-promoted copper(II) chloride supported on high surface area, porous alumina (84) ... 

Another version of a fluidized-bed reactor has been introduced by Vogelbusch (Austria). This reactor has an internal recirculation loop set up by means of a high flow impeller. The system utilises porous glass beads for immobilizing the cells. However, glass beads may not work with all types of cells. 

Methane, chlorine, and recycled chloromethanes are fed to a tubular reactor at a reactor temperature of 490—530°C to yield all four chlorinated methane derivatives (14). Similarly, chlorination of ethane produces ethyl chloride and higher chlorinated ethanes. The process is employed commercially to produce l,l,l-trichloroethane. l,l,l-Trichloroethane is also produced via chlorination of 1,1-dichloroethane with l,l,2-trichloroethane as a coproduct (15). Hexachlorocyclopentadiene is formed by a complex series of chlorination, cyclization, and dechlorination reactions. First, substitutive chlorination of pentanes is carried out by either photochemical or thermal methods to give a product with 6—7 atoms of chlorine per mole of pentane. The polychloropentane product mixed with excess chlorine is then passed through a porous bed of Fuller s earth or silica at 350—500°C to give hexachlorocyclopentadiene. Cyclopentadiene is another possible feedstock for the production of hexachlorocyclopentadiene. 

Catalytic A catalytic-membrane reactor is a combination heterogeneous catalyst and permselective membrane that promotes a reaction, allowing one component to permeate. Many of the reactions studied involve H9. Membranes are metal (Pd, Ag), nonporous metal oxides, and porous structures of ceran iic and glass. Falconer, Noble, and Speriy [in Noble and Stern (eds.), op. cit., pp. 669-709] review status and potential developments. 

An industrial chemical reacdor is a complex device in which heat transfer, mass transfer, diffusion, and friction may occur along with chemical reaction, and it must be safe and controllable. In large vessels, questions of mixing of reactants, flow distribution, residence time distribution, and efficient utilization of the surface of porous catalysts also arise. A particular process can be dominated by one of these factors or by several of them for example, a reactor may on occasion be predominantly a heat exchanger or a mass-transfer device. A successful commercial unit is an economic balance of all these factors. 

Normally when a small change is made in the condition of a reactor, only a comparatively small change in the response occurs. Such a system is uniquely stable. In some cases, a small positive perturbation can result in an abrupt change to one steady state, and a small negative perturbation to a different steady condition. Such multiplicities occur most commonly in variable temperature CSTRs. Also, there are cases where a process occurring in a porous catalyst may have more than one effectiveness at the same Thiele number and thermal balance. Some isothermal systems likewise can have multiplicities, for instance, CSTRs with rate equations that have a maximum, as in Example (d) following. 

These reactors for hquids and liquids plus gases employ small particles in the range of 0.05 to 1.0 mm (0.0020 to 0.039 in), the minimum size hmited by filterability. Small diameters are used to provide as large an interface as possible since the internal surface of porous pellets is poorly accessible to the hquid phase. Solids concentrations up to 10 percent by volume can be handled. In hydrogenation of oils with Ni catalyst, however, the sohds content is about 0.5 percent, and in the manufacture of hydroxylamine phosphate with Pd-C it is 0.05 percent. Fischer-Tropsch slurry reac tors have been tested with concentrations of 10 to 950 g catalyst/L (0.624 to 59.3 IbiTi/fF) (Satterfield and Huff, Chem. Eng. Sci., 35, 195 [1980]). 

In many important cases of reactions involving gas, hquid, and solid phases, the solid phase is a porous catalyst. It may be in a fixed bed or it may be suspended in the fluid mixture. In general, the reaction occurs either in the liquid phase or at the liquid/solid interface. In fixed-bed reactors the particles have diameters of about 3 mm (0.12 in) and occupy about 50 percent of the vessel volume. Diameters of suspended particles are hmited to O.I to 0.2 mm (0.004 to 0.008 in) minimum by requirements of filterability and occupy I to 10 percent of the volume in stirred vessels. 

Pore diffusion limitation was studied on a very porous catalyst at the operating conditions of a commercial reactor. The aim of the experiments was to measure the effective diffiisivity in the porous catalyst and the mass transfer coefficient at operating conditions. Few experimental results were published before 1970, but some important mathematical analyses had already been presented. Publications of Clements and Schnelle (1963) and Turner (1967) gave some advice. 

A tubular reactor is to be designed for the synthesis of methanol from a stoichiometric mixture of CO and Hj. The reaction occurs in the vapor phase using a solid catalyst in the form of porous spheres CO + 2H2 = CH3OH. The average mixture physical and thermodynamic data at 500 K and 10 Mpa are... 

Catalytic processes frequently require more than a single chemical function, and these bifunctional or polyfunctional materials innst be prepared in away to assure effective communication among the various constitnents. For example, naphtha reforming requires both an acidic function for isomerization and alkylation and a hydrogenation function for aromati-zation and saturation. The acidic function is often a promoted porous metal oxide (e.g., alumina) with a noble metal (e.g., platinum) deposited on its surface to provide the hydrogenation sites. To avoid separation problems, it is not unusual to attach homogeneous catalysts and even enzymes to solid surfaces for use in flow reactors. Although this technique works well in some environmental catalytic systems, such attachment sometimes modifies the catalytic specifici-... 

The values of the Michaelis-Menten kinetic parameters, Vj3 and C,PP characterise the kinetic expression for the micro-environment within the porous structure. Kinetic analyses of the immobilised lipase in the membrane reactor were performed because the kinetic parameters cannot be assumed to be the same values as for die native enzymes. 

---