Quantitative analysis procedures

Independently of the method used for evaluating the integrated intensity, the quantitative phase analysis of a given sample can be achieved through several methods. 

---

The quantitative analysis procedure involves benz extr of TNT, water extr of AN, and taking of the A1 content as insol residue. Moisture content is detd by the Karl Fischer method described in ASTM Method E203-62, except that 8 to lOg samples are added to methanol. Specific gravity is detd by water displacement, and workmanship by visual examination... 

The quantitative analysis procedure involves gravimetric detn of the HMX on a moisture-free basis after benzene extraction of, and differential detn of TNT. Moisture content is detd by conductometric titration of sample in an acetic-sulfuric acid suspension. Acetone insoluble matter is determined gravimetrically... 

Quantitative analysis procedures using infrared spectrometry utilize Beer s law. Thus only sampling cells with a constant pathlength can be used. Once the percent transmittance or absorbance measurements are made, the data reduction procedures are identical with those outlined in Chapter 7 (preparation of standard curve, etc.). 

When performing a quantitative analysis procedure using fluorometry, what parameter is measured by the instrument and plotted vs. concentration ... 

The actual soil content (level of pesticide contamination) of the fabrics was determined by quantitative analysis procedures. In this approach, the amount of soil actually present In the fabrics before and after laundering Is measured. The analysis procedure In this study Involved the separation of the soil (pesticide residues) from the fabrics by solvent extraction and analysis of the extracts by gas chromotography. 

Marecek and colleagues developed a new electrochemical method for the rapid quantitative analysis of the antibiotic monensin in the fermentation vats used during its production. The standard method for the analysis, which is based on a test for microbiological activity, is both difficult and time-consuming. As part of the study, samples taken at different times from a fermentation production vat were analyzed for the concentration of monensin using both the electrochemical and microbiological procedures. The results, in parts per thousand (ppt), are reported in the following table. 

Commercial washing soda contains approximately 30-40% w/w Na2C03. One procedure for the quantitative analysis of washing soda contains the following instructions ... 

A quantitative analysis for vitamin Bi was carried out using this procedure. When a solution of 100.0 ppm Bi and 100.0 ppm o-ethoxybenzamide was analyzed, the peak area for vitamin Bi was 71 % of that for the internal standard. The analysis of a 0.125-g vitamin B complex tablet gave a peak area for vitamin Bi that was 1.82 times as great as that for the internal standard. How many milligrams of vitamin Bi are in the tablet ... 

The earliest examples of analytical methods based on chemical kinetics, which date from the late nineteenth century, took advantage of the catalytic activity of enzymes. Typically, the enzyme was added to a solution containing a suitable substrate, and the reaction between the two was monitored for a fixed time. The enzyme s activity was determined by measuring the amount of substrate that had reacted. Enzymes also were used in procedures for the quantitative analysis of hydrogen peroxide and carbohydrates. The application of catalytic reactions continued in the first half of the twentieth century, and developments included the use of nonenzymatic catalysts, noncatalytic reactions, and differences in reaction rates when analyzing samples with several analytes. 

A bulk sample is the last choice and the least desirable. It should be submitted "for laboratory use only" if there is a possibility of contamination by other matter. The type of bulk sample submitted to the laboratory should be cross-referenced to the appropriate air samples. A reported bulk sample analysis for quartz (or cristobalite) will be semi-quantitative in nature because (1) The XRD analysis procedure requires a thin layer deposition for an accurate analysis. (2) The error for bulk samples analyzed by XRD is unknown because the particle size of nonrespirable bulk samples varies from sample to sample. 

In a modern industrialised society the analytical chemist has a very important role to play. Thus most manufacturing industries rely upon both qualitative and quantitative chemical analysis to ensure that the raw materials used meet certain specifications, and also to check the quality of the final product. The examination of raw materials is carried out to ensure that there are no unusual substances present which might be deleterious to the manufacturing process or appear as a harmful impurity in the final product. Further, since the value of the raw material may be governed by the amount of the required ingredient which it contains, a quantitative analysis is performed to establish the proportion of the essential component this procedure is often referred to as assaying. The final manufactured product is subject to quality control to ensure that its essential components are present within a pre-determined range of composition, whilst impurities do not exceed certain specified limits. The semiconductor industry is an example of an industry whose very existence is dependent upon very accurate determination of substances present in extremely minute quantities. 

The function of the analyst is to obtain a result as near to the true value as possible by the correct application of the analytical procedure employed. The level of confidence that the analyst may enjoy in his results will be very small unless he has knowledge of the accuracy and precision of the method used as well as being aware of the sources of error which may be introduced. Quantitative analysis is not simply a case of taking a sample, carrying out a single determination and then claiming that the value obtained is irrefutable. It also requires a sound knowledge of the chemistry involved, of the possibilities of interferences from other ions, elements and compounds as well as of the statistical distribution of values. The purpose of this chapter is to explain some of the terms employed and to outline the statistical procedures which may be applied to the analytical results. 

High performance liquid chromatography is used for the separation and quantitative analysis of a wide variety of mixtures, especially those in which the components are insufficiently volatile and/or thermally stable to be separated by gas chromatography. This is illustrated by the following method which may be used for the quantitative determination of aspirin and caffeine in the common analgesic tablets, using phenacetin as internal standard where APC tablets are available the phenacetin can also be determined by this procedure. 

Impact Sensitivity Determinations of Explosive Compounds Tested During the Period from 1 January to 1 November 1950", NOL NAVORD 1589, (1 Nov 1950), Table V 22) J.M. Rosen, Procedure for the Quantitative Analysis of Nitroform and Bis(trinitroethyl)urea Using Tetra-phenylarsonium Chloride , NOL NAVORD 1729 20 Dec 1950) 23) N.L. Drake et al, U of Md... 

The reactions described in this section are used for the quantitative analysis of sulphones. Extreme, forcing, oxidizing conditions are used for these procedures. Sulphox-ides and sulphides may also be analysed in the same way and so the discussion also applies to these types of compounds. 

Quantitative estimates of the mass of a particular solute present in a sample are obtained from either peak height or peak area measurements. The values obtained are then compared with the peak height or area of a reference solute present in the sample at a known concentration or mass. In this chapter quantitative analysis by LC will be discussed but the procedures described should not be considered as entirely appropriate for other types of chromatographic analysis. Those interested in general quantitative chromatographic analysis including GC and TLC are referred to the book by Katz (4). 

There are two basic methods used in quantitative analysis one uses a reference standard with which the peak areas (peak heights) of the other solutes in the sample are compared the other is a normalization procedure where the area (height) of any one peak is expressed as a percentage of the total area (heights) of all the peaks. There are certain circumstances where each method is advantageous, and providing they are used carefully and appropriately all give approximately the same accuracy and precision. 

In contrast to the well-established methods for identifying and quantifying naturally occurring chlorophylls, very few reports concern quantitative analysis of chlorophyllin copper complexes in color additives and in foodstuffs. Analytical methods proposed are based on spectral properties, elemental analysis, chromatographic separation, and molecular structure elucidation or a combination of these procedures. 

Spectrophotometric determinations aim at evaluation of actual versus permitted concentrations of synthetic colorants. Quantitative analysis of colorants resulting from these procedures can be performed by various techniques. Spectrophotometry allows individual or simultaneous quantitative analyses of colorant mixtures having similar absorption spectra. " ... 

---