Pressure Classifications

Fans are classified according to the discharge pressure. Reprinted per written permission from the Air Movement and Control Association International, Inc., the AMCA Standard 99-1401-66 from Standards Handbook 99-56 1986, the total static pressure classification for operating limits for central station units is as follows ... 

All ducts identify materials of construction, insulation type, and pressure classification. 

The application areas of bimodal polyethylenes are the same as for corresponding uni-modal resins. However, improved product property combinations, such as stiffness-impact balance, result in products with higher performance. For example, without bimodal polyethylene and control over the MWD and comonomer incorporation, development of HDPE pipe materials with higher pressure classification would not have been possible [15, 16]. Another new opportunity is material reduction (source reduction) without compromising the properties of the ready-made plastic products. Depending on the end use, e.g. in film application a thickness reduction of 10-30% is possible. 

The Seventh Report of the Joint National Committee on Prevention, Detection, Evalution, and Treatment of High Blood Pressure (JNC 7 National Institutes of Health, 2004) is a definitive publication concerning the treatment of hypertension. It provides the following blood pressure classifications for adult blood pressures ... 

The TEMA standards specify the manufacturing tolerances for various mechanical classes, the range of tube sizes and pitches, baffling and support plates, pressure classification, tubesheet thickness formulas, and so on, and must be consulted for all these details. 

The principles referred to so far are common to all New Approach directives. The individual directives obviously need to be specific on topics such as the scope, the essential requirements, the classification of the products and on the use of modules for conformity assessment. The pressure equipment directive includes some additional sector specific dispositions which relate to recognised third party organisations , the European approval for materials , a committee for pressure equipment and the user inspectorates . 

The directive entitles the Commission to take, for safety reasons, any appropriate measures with respect to classification of pressure equipment or assemblies. In that task, the Commission is assisted by a standing committee on pressure equipment which is composed of representatives appointed by the Member States and chaired by a representative of tbe Commission. 

The basis of the classification is that each of the size ranges corresponds to characteristic adsorption effects as manifested in the isotherm. In micropores, the interaction potential is significantly higher than in wider pores owing to the proximity of the walls, and the amount adsorbed (at a given relative pressure) is correspondingly enhanced. In mesopores, capillary condensation, with its characteristic hysteresis loop, takes place. In the macropore range the pores are so wide that it is virtually impossible to map out the isotherm in detail because the relative pressures are so close to unity. 

The hysteresis loops to be found in the literature are of various shapes. The classification originally put forward by de Boer S in 1958 has proved useful, but subsequent experience has shown that his Types C and D hardly ever occur in practice. Moreover in Type B the closure of the loop is never characterized by the vertical branch at saturation pressure, shown in the de Boer diagrams. In the revised classification presented in Fig. 3.5, therefore. Types C and D have been omitted and Type B redrawn at the high-pressure end. The designation E is so well established in the literature that it is retained here, despite the interruption in the sequence of lettering. 

A new classification of hysteresis loops, as recommended in the lUPAC manual, consists of the four types shown in the Figure below. To avoid confusion with the original de Boer classification (p. 117), the characteristic types are now designated HI, H2, H3 and H4 but it is evident that the first three types correspond to types A, E and B, respectively, in the original classification. It will be noted that HI and H4 represent extreme types in the former the adsorption and desorption branches are almost vertical and nearly parallel over an appreciable range of gas uptake, whereas in the latter they are nearly horizontal and parallel over a wide range of relative pressure. Types H2 and H3 may be regarded as intermediate between the two extremes. 

These simple examples serve to show that instinctive ideas about symmetry are not going to get us very far. We must put symmetry classification on a much firmer footing if it is to be useful. In order to do this we need to define only five types of elements of symmetry - and one of these is almost trivial. In discussing these we refer only to the free molecule, realized in the gas phase at low pressure, and not, for example, to crystals which have additional elements of symmetry relating the positions of different molecules within the unit cell. We shall use, therefore, the Schdnflies notation rather than the Hermann-Mauguin notation favoured in crystallography. 

When constmction is complete, the pipeline must be tested for leaks and strength before being put into service industry code specifies the test procedures. Water is the test fluid of choice for natural gas pipelines, and hydrostatic testing is often carried out beyond the yield strength in order to reHeve secondary stresses added during constmction or to ensure that all defects are found. Industry code limits on the hoop stress control the test pressures, which are also limited by location classification based on population. Hoop stress is calculated from the formula, S = PD/2t, where S is the hoop stress in kPa (psig) P is the internal pressure in kPa (psig), and D and T are the outside pipe diameter and nominal wall thickness, respectively, in mm (in.). 

In 1991, the European fabric softener market took a sharp turn. Producers in Germany, the Netherlands, and later in Austria and Switzerland voluntarily gave up the use of DHTDMAC (238) because of pressure from local environmental authorities, who gave an environmentally hazardous classification to DHTDMAC. A number of esterquats were developed as candidates to become successors to DHTDMAC (see Fig. 1). The ester group facihtates biodegradation. 

Glassification of Phase Boundaries for Binary Systems. Six classes of binary diagrams have been identified. These are shown schematically in Figure 6. Classifications are typically based on pressure—temperature (P T) projections of mixture critical curves and three-phase equiHbria lines (1,5,22,23). Experimental data are usually obtained by a simple synthetic method in which the pressure and temperature of a homogeneous solution of known concentration are manipulated to precipitate a visually observed phase. 

There are many ways to classify a tank. Although there is no universal method, a classification commonly employed is based on the tank s internal pressure. 

To a large exteat, the vapor pressure of the substance stored determines the shape and, consequently, the type of tank used. The roof shape of a tank may be used to classify the type of tank. This classification is self-explanatory to tank fabricators and erectors. Also important is the tank bottom. 

FIG. 20-71 Classification of agglomeration processes by agitation intensity and compaction pressure. Relative density is with respect to primary particle density and equals (1 — e) where e is the solid volume fraction. Reprinted from Granulation and Coating Technologies for High-Value-Added Industties, Ennis and Litster (1996) with permission of E G Associates. All rights reserved. 

Ignition of flammable Provide safe separation distances release resulting in fire. Develop appropriate area electrical or explosion. classification Provide ignition source control Place ignition sources in positive pressure enclosure and buildings Provide adequate ventilation API RP500 BS 5345 BS 5958 NFPA-70 NFPA-77... 

---