Polymers, carbanionic

Successive addition of monomers to the end of macromolecular initiator is the usual technique for the synthesis of tailored blockcopolymers. Anionic polymerization of pivalolactone, a-pyrrolidone— and the NCA of T-methyl-D-glutamate -2 was started from the end group of a prepolymer consisting carboxylate group or acyl lactam group or amino group. Living polymer of C-capro-lactone was expected to be formed by the initiated polymerization from polymer carbanion under kinetic controlled condition. 

Ionic mechanisms for the preparation of block copolymers are a very important tool of the synthetic polymer chemist. A feature of many homogeneous anionic polymerizations in solution is that termination can be avoided by careful control of experimental conditions. In fact, an infinite life of the active chain end is theoretically possible, and this has led to the term living polymers. Polymer carbanions can resume growth after the further addition of monomer. By changing the monomer composition, block copolymerization is readily initiated, and this process can be repeated. A major advantage of this... 

The polymer carbanion can also be used as an anionic initiator for polymerizing a conventional organic monomer to generate a poly-phosphazene-co-organic polymer (Fig. 3.50). The polystyrene graft copolymer prepared as shown above is actually separated into the individual polystyrene and polyphosphazene phases. This is found by the detection of two separate Tg s at +100 °C and +37 °C. 

A fairly narrow MWD results from this polymerization. The living nature of polymerization allows control of branching and the production of rubbers with broadened MWDs, as shown in Fig. 8, for the case of post-reaction of reactive polymer carbanion chain ends with DVB. These branched polymers are easily oil-extended and exhibit lower cold flow than their hnear counterparts. 

The nature of the chain ends of HTBR has been further investigated by using a radiochemical method to determine the number of active polymer carbanions formed with the Ba/Mg/Al catalyst. The basis of this method is the quantitative reaction of metal-polymer bonds with tritium atoms of tritiated alcohol, as shown below ... 

Polymer carbanion (P ) cyc/o-[SiMc20]3 P—SiMc20 Cyclopolysiloxanes (polymerization) 125... 

Polymer carbanion (P ) 1. MgBr2 2. Br2 3. AgC104 P+C104 Tetrahydrofuran (polymerization) 129... 

M. Szwarc, Carbanions, Pining Polymers andPlectron Transfer Processes, Wiley-Interscience, New York, 1968. 

M. S2ware, Carbanions, Firing Polymers, andElectron Transfer Processes, Interscience PubUshers, New York, 1968. 

Anionic polymerization offers fast polymerization rates on account of the long life-time of polystyryl carbanions. Early studies have focused on this attribute, most of which were conducted at short reactor residence times (< 1 h), at relatively low temperatures (10—50°C), and in low chain-transfer solvents (typically benzene) to ensure that premature termination did not take place. Also, relatively low degrees of polymerization (DP) were typically studied. Continuous commercial free-radical solution polymerization processes to make PS, on the other hand, operate at relatively high temperatures (>100° C), at long residence times (>1.5 h), utilize a chain-transfer solvent (ethylbenzene), and produce polymer in the range of 1000—1500 DP. 

Solvent for Displacement Reactions. As the most polar of the common aprotic solvents, DMSO is a favored solvent for displacement reactions because of its high dielectric constant and because anions are less solvated in it (87). Rates for these reactions are sometimes a thousand times faster in DMSO than in alcohols. Suitable nucleophiles include acetyUde ion, alkoxide ion, hydroxide ion, azide ion, carbanions, carboxylate ions, cyanide ion, hahde ions, mercaptide ions, phenoxide ions, nitrite ions, and thiocyanate ions (31). Rates of displacement by amides or amines are also greater in DMSO than in alcohol or aqueous solutions. Dimethyl sulfoxide is used as the reaction solvent in the manufacture of high performance, polyaryl ether polymers by reaction of bis(4,4 -chlorophenyl) sulfone with the disodium salts of dihydroxyphenols, eg, bisphenol A or 4,4 -sulfonylbisphenol (88). These and related reactions are made more economical by efficient recycling of DMSO (89). Nucleophilic displacement of activated aromatic nitro groups with aryloxy anion in DMSO is a versatile and useful reaction for the synthesis of aromatic ethers and polyethers (90). 

The dimer behaves simultaneously as a radical and as a carban-ion, and thus the radical end might grow by a radical mechanism, anionic polymerization proceeding from the carbanion end. This behavior is particularly interesting when two monomers are present in the system, one polymerizable by a radical but not by an anionic mechanism, the other behaving in the opposite sense. In such a hypothetical case the resulting product would be a block polymer, -A—A. . . A—B—B. . . B-. 

Addition of styrene to a green solution of naphthalene" Na+ in tetrahydrofuran leads to an instantaneous change of color from green to red. Styrene polymerizes rapidly and quantitatively within a few seconds, and when the reaction is completed, addition of water converts the red solution of polystyryl carbanions into colorless solution of polystyrene. After precipitation of the polymer it was shown spectroscopically25 that the residual solution contains an amount of naphthalene equal to that used in the preparation of the initiating catalyst. This observation confirms the proposed mechanism of initiation of the polymerization. 

Formation of block polymers is not limited to hydrocarbon monomers only. For example, living polystyrene initiates polymerization of methyl methacrylate and a block polymer of polystyrene and of polymethyl methacrylate results.34 However, methyl methacrylate represents a class of monomers which may be named a suicide monomer. Its polymerization can be initiated by carbanions or by an electron transfer process, the propagation reaction is rapid but eventually termination takes place. Presumably, the reactive carbanion interacts with the methyl group of the ester according to the following reaction... 

Platinum-cobalt alloy, enthalpy of formation, 144 Polarizability, of carbon, 75 of hydrogen molecule, 65, 75 and ionization potential data, 70 Polyamide, 181 Poly butadiene, 170, 181 Polydispersed systems, 183 Polyfunctional polymer, 178 Polymerization, of butadiene, 163 of solid acetaldehyde, 163 of vinyl monomers, 154 Polymers, star-shaped, 183 Polymethyl methacrylate, 180 Polystyrene, 172 Polystyril carbanions, 154 Potential barriers of internal rotation, 368, 374... 

Table 1. Some imide ions and carbanions used in salts to enhance polymer electrolyte conductivity and reduce crystallinity...

Szwarc, M. Carbanions, living polymers and electron transfer process. New York Inter-science 1968... 

Polymerization of t-butyl methacrylate initiated by lithium compounds in toluene yields 100% isotactic polymers 64,65), and significantly, of a nearly uniform molecular-weight, while the isotactic polymethyl methacrylate formed under these conditions has a bimodal distribution. Significantly, the propagation of the lithium pairs of the t-Bu ester carbanion, is faster in toluene than in THF. In hydrocarbon solvents the monomers seem to interact strongly with the Li+ cations in the transition state of the addition, while the conventional direct monomer interaction with carbanions, that requires partial dissociation of ion-pair in the transition state of propagation, governs the addition in ethereal solvents. 

The observation of Tsuji et al. 148) concerned with copolymerization of 1- or 2-phenyl butadiene with styrene or butadiene illustrates again the importance of the distinction between the classic, direct monomer addition to the carbanion, and the addition involving coordination with Li4. The living polymer of 1- or 2-phenyl butadiene initiated by sec-butyl lithium forms a block polymer on subsequent addition of styrene or butadiene provided that the reaction proceeds in toluene. However, these block polymers are not formed when the reaction takes place in THF. The relatively unreactive anions derived from phenyl butadienes do not add styrene or butadiene, while the addition eventually takes place in hydrocarbons on coordination of the monomers with Li4. The addition through the coordination route is more facile than the classic one. 

Shima M, Smid J, Szwarc M (1964) J. Polymer Sci. Polym. Lett. 2 735 Szwarc M (1968) Carbanions, Living Polymers and Electron Transfer Processes. Wiley Publ. 

Interest in anionic polymerizations arises in part from the reactivity of the living carbanionic sites4 7) Access can be provided to polymers with a functional chain end. Such species are difficult to obtain by other methods. Polycondensations yield ro-functional polymers but they provide neither accurate molecular weight control nor low polydispersity. Recently Kennedy51) developed the inifer technique which is based upon selective transfer to fit vinylic polymers obtained cationically with functions at chain end. Also some cationic ring-opening polymerizations52) without spontaneous termination can yield re-functional polymers upon induced deactivation. Anionic polymerization remains however the most versatile and widely used method to synthesize tailor made re-functional macromolecules. 

Poly (alkyl methacrylate) macromonomers are formed by reaction of the living polymer with VBC. This method was shown to be free of side reactions and quantitative, in spite of the low nucleophilicity of the carbanionic site involved 72,75). 

The synthesis of comb-like polymers with regular branching (in contrast to random branching) has been performed in the following way 91) A linear polystyrene precursor fitted with carbanionic sites at both ends is reacted first with 1,1-diphenylethylene (to decrease the nucleophilicity of the sites) and then with a calculated amount of triallyloxytriazine to get chain extension. Each triazine residue still carries one allyloxy... 

---